| To add a NEW remote |
METHOD #1
1. Disarm panel and Enter 78738 from keypad. System will arm in “HOME” mode
2. Press button #1 (largest button) until arm system disarms. It should take four presses
METHOD #2
1. PRESS and RELEASE Program button, LED will turn ON
2. Immediately press button 1 on new remote control 3 times
3. LED on receiver should go OFF, indicating remote learned
Note: If LED stays ON, remote not learned, remove & replace harness, wait 15 sec and try again
|
| Default Code Encryptor |
METHOD #1
Disarm panel, enter 76278 from keypad, Keypad will “beep” or lights turn off to confirm delete
METHOD #2
PRESS and HOLD program button, LED will turn ON for four seconds then OFF then ON again
|
LED Wiring – DO NOT CONNECT LED DIRECTLY TO GROUND!
LED is low voltage type and must run through Code Encryptor II
If you attempt to connect purple wire directly to ground (-) the LED will burn out
|
Channel 2 Outputs – (Every time button #2 is pressed, two outputs happen simultaneously.)
| Output #1 |
Momentary Contact Closure for Opening and Closing garage door |
| Output #2 |
500ma (-) output for 3 minutes, (See Channel 2 Timed Output) |
|
| Garage Door Interface |
All garage doors have wall mounted push button that activates the door via a two-wire connection
Make connection at push button switch or garage door motor where these two wires terminate
Attach Code Encryptor Red/White & White wires from to these two wires
Most garage doors use terminals 1 & 2. For MOM Crusader models, use terminals 2 and 3
| |
Red/White |
(Channel 2 Output) |
|
White |
(Channel 2 Common) |
|
| Channel 2 Timed Output |
|
Every time button 2 is pressed the Gray wire sends a 500ma (-) output for 3 minutes.
Application #1 – If you hardwire garage door use this output to trigger a 12VDC relay that energizes
when you open or close garage door extending entry/exit delay by 3 minutes, for security make
entry delay minimal so if thief enters through garage, entry delay will be short
Application #2 – You can use this output to drive entry/exit illumination
Every time customer enters or exits house this output can trigger a relay or X-10 Powerflash module
to interface with driveway, porch or Malibu lighting illuminating way as they leave and return home
The output activates automatically when you press button 2 on remote and will shut off after 3 minutes
|
| Channel 3 Applications |
Relay Output
Occasionally, you may want to use Channel 3 for control of optional accessories
Code Encryptor II provides the ability to reconfigure Channel 3 to a variety of outputs using
on-board jumpers. The output provided from Code Encryptor II is 5amp from C relay (Common, N/O, N/C)
| |
Jumper Configuration |
Channel 3 Output Type |
|
Both jumpers in (default) |
Momentary output |
|
Jumper closest to the harness removed |
Latching (on/off) output |
|
Jumper farthest from the harness removed |
75sec timed output |
|
Both jumpers out |
150sec timed output |
This output is a 5 amp Form C relay (Common, N/O/, N/C) to energize relay, press & release button 3
|
| Deactivating the Panic Feature |
In the event user does not want panic button, it can be de-activated from Codee Encryptor II
Step 1) Unplug the wire harness from the Code Encryptor II
Step 2) Press and HOLD the program button
Step 3) While HOLDING program button, plug harness in. LED will turn ON
Step 4) Wait until LED turns “OFF”
Step 5) Once LED has turned “OFF” release button
|
| Installation for Keyswitch Arming |
| Red |
Aux + |
| Black |
Aux – |
| Brown/White |
Zone programmed for keyswitch arming |
| Brown |
Common adjacent to zone |
|
| Specifications |
RECEIVER
12VDC Power Input
Channels 1 Data outputs
Channel 2 Relay N/O, Comm (10amp)
Channel 3 selectable: Form C Relay (N/O, N/C, Comm) 5amp
This output can be reconfigured from pulsed output to latching, 75 or 150 second timed output
Channel 3 – Keypad panic data output (Programmable On or OFF)
Frequency 303Mhz
Stand by Power Consumption 15ma
Temperature Range -5°F to 160°F (Indoor use only)
REMOTE CONTROL
Battery 12VDC Mini (Part #GP23A) Range 150+ feet
|
| Optional Reversible Outputs |
Channel 2 has two independent outputs that occur when button 2 is pressed
The first output is a momentary relay contact closure which is intended for the use of opening
and closing garage door. This is primary output and can not be changed or reconfigured.
The second output is a (-) 500ma transistor output to provide a zone bypass or illuminated entry/exit
If not using relay for Channel 3 you may choose to swap (-) transistor output for relay
In this instance you will then have two contact closures every time Button # 2 is pressed
The standard momentary contact closure and ALSO a Form C relay that energize for 3 minutes
every time garage door is opened or closed
|
| To Swap transistor and relay outputs |
| Step 1) |
While watching the LED on the CE II receiver press and HOLD button 1 and 3 simultaneously
on the remote control until LED on CE II receiver illuminates. (approx. 5 seconds)
|
| Step 2) |
To make channel 2 a relay press program button on CE II Receiver TWICE
to make it a transistor output press ONCE (Default setting)
|
| Step 3) |
Wait 10 seconds and CE II will automatically reconfigure the outputs |
|
| NOTE – Even if you swap outputs, Panic button will operate if you press and HOLD for three seconds |
