Silent Knight 5207 Program

All Programming for this panel must be done through either the 5230 remote annunciator (touchpad),

5541 Download Software or a 5521 desktop programmer.

The Customer can’t do any programming from the main panel (ie. Code Change)

To Enter Programming:	You Can Enter Step Programming by pressing 2 + 7 +Enter + Zero Code. If after you enter this it says TRY AGAIN, then the zero code has been changed from the default 123456. Try the first two of the address and the last two of the account number as the zero code. This works 50% of the time.
To Exit Programming:	To Exit programming Enter STEP + STEP + CLEAR + CLEAR

How to use Step Programming
	1.	Selecting Options: Once the display reads “1 PWR UP CLR”, press ENTER to display the data for Step 1. The top line of the display will show a abbreviation of the option, the bottom line will show the data for that step.
	2.	SCROLL: For most options, you enter data the same way as if using a calculator. The digits appear on the right side and scroll to the left as you enter them.
	3.	TOGGLE: In some steps, pressing a key will cause the corresponding digit to appear and disappear on the display. When a digit appears, it indicates that the option has been selected. When there is a dash it indicates that that option hasn’t been selected.
	4.	ENTER NUMBERS GREATER THAN 9: Use the Shift key as shown below to enter numbers 10-15. Hexadecimal digits (in Parentheses) appear on the screen to represent these numbers.
		SHIFT 1 = 10(A) SHIFT 2 = 11(B) SHIFT 3 = 12(C) SHIFT 4 = 13(D) SHIFT 5 = 14(E) SHIFT 6 = 15(F)
	5.	ADVANCING TO THE NEXT OPTION: Press the ENTER key to advance to the next option. To skip more options keep pressing the ENTER key.
	6.	GOING DIRECTLY TO A STEP: Press STEP STEP and the LCD will show “1 PWR UP CLR”. Key in the desired step number and ENTER.
	7.	NOTE: Some steps have sub steps, to get to these enter the step number then STEP and the SUBSTEP number followed by ENTER.

Step #

Option

Default

1st digit:
Bell Test at Restore:
0 = No test
8 = Test

2nd digit:
Power up Mode Report:
0 = No report
1 = Report sent

Enable Devices:
0 = Dialer
1 = Printer

2-6 Unused
7 = 24V system

0 – – – – – – 7

↑ (Do not change factory programming.) ↑

Options:
0 = Cadenced pulsing
1 = Code required at panel
2 = Trouble alert tone for
pre-alarm sound
3 = Pulsing fire bells

4 = Sound smoke delay
5 = Report fast restores
6 = Do not de-select.
7 = Time displays in
military format

– – – – – – 6 –

1st digit:
(Display Rate)
0 = .5 sec
1 = 1 sec.
2 = 1.5 sec.
3 = 3 sec.

2nd digit:
0-7 = Max. number of
supervised touchpads
(0 means none.)

Misc. Options:
0 = Report walk tests
1 = Do NOT de-select
2 = Detect ground fault

3 = Sequential bell test
4 – 7 = Supervise bells 1-4

-1234567

6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10

Internal Zone Options (zones 1-8)
24-hour alarm (do not change default)
Select zones to be supervised for trouble
Unused (do not change default)
Zones will be Normally Open (do not change default)
Zone response speed 2 or 4
Zone response speed 3 or 4
Unused
Pre-alarm delay
Smoke verification delay
Number of zones that can be disabled

12345678
12345678
– – – – – – – –
12345678
12345678
– – – – – – – –
– – – – – – – –
– – – – – – – –
– – – – – – – –
12345678

7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10

External Zone Options (zones 9-16)
24-hour alarm (do not change default)
Select zones to be supervised for trouble
Unused (do not change default)
Zones will be Normally Open (do not change)
Zone response speed 2 or 4
Zone response speed 3 or 4
Unused
Pre-alarm delay
Smoke verification delay
Number of zones that can be disabled

90123456
90123456
– – – – – – – –
90123456
90123456
– – – – – – – –
– – – – – – – –
– – – – – – – –
– – – – – – – –
90123456

Total number of zones in system90847610 8

Dialer Options:
0 = Retry if fail
1 = Enable phone line 2
2 = Unused (do not select)
3 = Ground start (do not use
in UL installations)

4 = Enable TLM
5 = Answer ring detect
6 = Unused (do not select)

– 1 – – – 5 – 7

Total number of dialing attempts.

Number of dialing attempts before dialer fail.

Low AC hours (UL requires range of 6-12 hours.)

Number of rings to activate downloading.

Telephone # for reporting:

14.1

Report alarms to:
1 = Ph. #1
2 = Ph. #2
3 = Ph. #3
4 = Ph. #4

Report troubles to:
5 = Ph. #1
6 = Ph. #2
7 = Ph. #3
8 = Ph. #4

1 – – – 5 – – –

14.2

Report disabled zones to:
1 = Ph. #1
2 = Ph. #2
3 = Ph. #3
4 = Ph. #4

Report restores to:
5 = Ph. #1
6 = Ph. #2
7 = Ph. #3
8 = Ph. #4

1 – – – 5 – – –

14.3

Report open resets to:
1 = Ph. #1
2 = Ph. #2
3 = Ph. #3
4 = Ph. #4

5-8 = Not used.

1 – – – – – – – –

14.4

1-4 = Not used.

Report tests to:
5 = Ph. #1
6 = Ph. #2
7 = Ph. #3
8 = Ph. #4

– – – – 5 – – –

14.5

Must Report:
1 = Ph. #1
2 = Ph. #2
3 = Ph. #3
4 = Ph. #4

Select Options:
5 = Line 1 is Touch-Tone
6 = Line 1 is Touch-Tone
7 = Use Touch-Tone only
8 = Enable 16-zone reporting

1 – – – – – – –

Computer phone number for up/downloading.

[blank]

16.1
16.2
16.3
16.4

Central station phone numbers:
Phone number 1
Phone number 2
Phone number 3
Phone number 4

5551234567890
– – – – – – – –
– – – – – – – –
– – – – – – – –

17.1
17.2
17.3
17.4

Central station account numbers:
Account number 1
Account number 2
Account number 3
Account number 4

005207
– – – – – – – –
– – – – – – – –
– – – – – – – –

18.1
to
18.4

1st digit:
# of attempts before
switching to next account
for Accounts 1-4.

2nd digit:
Dialer frmt Accts. 1-4:

0 = SIA8	4 = BFSK23
1 = FSK1	5 = SIA20
2 = Not used	6 = SK4+2
3 = BFSK14

1 0

19.1
to
19.4

Phone opts for accts 1-4:
0 = Unused
1 = Use line 1 only
2 = Use line 2 only

3 = 9000 Direct (do not select)
4-9 = Unused (do not select)

– – – – – – – –

20.1
20.2
20.3
20.4
20.5
20.6

Duration of delays:
Bell shutdown time delay
Unused (Do not change)
Pre-alarm delay
Smoke verification delay
Smoke reset time
Unused (Do not change)

90
30
30
30
2
24

Test Time

000000

22.0
22.1
22.2
to
22.9

Secret Codes:
Installer’s code
Main user’s code
Other users (basicfunctions – can reset
alarms and disable zones).

123456
1111
[blank]

23.1
23.2
23.3
23.4
23.5
23.6

Relays (1-4) and bells (5-8) to activate for:
Pre-alarm conditions
Tamper alarms
Special (auxiliary) alarms
Fire alarms
Trouble conditions 1
No silence conditions

– – – – – – – –
– – – – – – – –
– – – – – – – –
– – – – 5678
– – – – – – –
– – – – – – – –

24.0
24.1
to
24.16

Alarm relay (1-4), bells (5-8) activate by zN.
Bells and relays Activate during a fire drill.
Bells and relays to activate for alarms in
zones 1-16.

– – – – – – – –
– – – – – – – –

25.1
to
25.16

1st digit: Audible signal
0 = Bells can shut down
2 = Cross alarm delay
4 = No manual bell sound
8 = No auto bell shutdown
A = Cross alarm and
no shutdown

2nd digit: Zone type
0 = Fire drill
1 = Fire
3 = Panic
5 = Tamper
6 = Sprinkler
7 = Undefined auxiliary
8 = Water
9 = Heat
A = Cold
B = Local
C = Unused

8 1

26.1
to
26.16

Zone location descriptions. (Click HERE for word list)
Press 1 to toggle words from first list and press
2 to toggle words from second list, ENTER to save.

WORDS

Length of temporal (pulsing) pattern

28.1
28.2
28.3
28.4

Cadence pattern (used with step 27)
First group of 8 bits
Second group of 8 bits
Third group of 8 bits )
Fourth group of 8 bits
(Each substep controls up to four seconds.

12345678
12345678
12345678
– – – – – – – –