Silent Knight 5204 Basics
| Function Name |
Explanation 5230 Annunciator |
Keystrokes | Built-in Touchpad |
| Clear |
Allows you to start again if you enter the wrong keystrokes. If you enter a function incorrectly on the 5230, the annunciators PZT buzzer will emit a long, high-pitched tone |
Clear | Clear |
| System Test |
Causes the system to test the 4180 outputs, the 7-segment LED display, bells, sirens, and communicator |
0 + Enter + installer or MC | 0 + Enter |
| Reset Alarms |
After a smoke alarm has been triggered, this function removes smoke detector power for the programmed length of time (SMOKE VER. TIME – step 25 in 5230 programming). This allows the smoke detector to sense new alarm conditions. |
1 + Enter + installer or MC | 1 + Enter + installer or MC |
| Clear Alarm Memory |
1. Clears all data out of the alarm memory 2. Resets the 4180 Status Display Module |
2 + Enter + installer or MC | 2 + Enter |
| Reset Dialer | Aborts an in-progress call to the central station | 3 + Enter + installer | 3 + Enter + installer |
| Display Alarm Memory |
Displays events currently saved in the alarm memory. It is recommended that you clear the alarm memory after displaying it (see CLEAR ALARM MEMORY.) |
5 + Enter + installer or MC | 5 + Enter |
| Display Troubles | Displays trouble conditions | 6 + Enter + installer or MC | 6 + Enter |
|
Silence trouble or alarm conditions |
Silences bells/horns that are in trouble or alarm. (On-board beeper and local annunciators continue to sound until serviced. See section 2.6 for more information.) |
Silence + installer or MC | Silence |
| Fire Drill |
Causes the system to sound an alarm and report a “FIRE TEST” |
2 + 0 + Enter + installer or MC | 2 + 0 + Enter + installer |
| To end fire drill | Silence + installer or MC | Silence | |
| Disable/Enable |
Disables a zone (prevents it from responding to an alarm condition) or reactivates a disabled zone. When you disable a zone, a trouble buzzer will sound. |
Enter the zone # (1-4) + Disable + installer or MC |
Enter the zone # (1-4) + Disable + installer or MC |
| Keystrokes for 5230 OR Built-in Touchpad | |||
| Walk Test |
Allows you to test the system. When you enter this mode, the LCD will indicate that you are in the WALK TEST mode. When a zone is violated the bell outputs will become active for approximately 6 seconds |
2 + 2 + Enter + installer To exit with 5230, press Step + Step + Clear + Clear To exit with Built-in, press Silence + Silence + Clear + Clear |
|
| Zone Trouble |
Allows you to locate and correct problems. The use of this mode is described in section 28.2 |
2 + 5 + installer To exit with 5230, press Step + Step + Clear + Clear To exit with Built-in, press Silence + Silence + Clear + Clear |
|
| Programming mode |
Allows you to program 5204 options stored on the EEPROM. Instructions for using mode 27 can be found in section 23. |
2 + 7 + installer To exit with 5230, press Step + Step + Clear + Clear To exit with Built-in, press Silence + Silence + Clear + Clear |
|
| Silencing the system |
To silence the on-board trouble tone, follow these steps Disable the zone by pressing the zone number + Shunt (Or disable) + installer or MC Reset the system by pressing 1 + Enter + installer or MC The zone is now in trouble because of the disabled zone and can be silenced in the normal way by pressing Silence |
||
| Set Time |
To set the time, follow this procedure: 1. Press 9 + Enter. the 7-segment display will show -9, indicating that you are in the SET TIME mode. 2. Enter installer code. The SET MODE LED will turn on. 3. Enter the time in military time, using a string of 4-digits. When you have pressed the fourth digit, the SET MODE LED will turn off. EXAMPLE: To set the time of 3:30PM, press the following digits after entering the SET TIME mode: 1530 |
||