GE / ITI / UC Concord Express Wiring
| These pannels cannot be remotely armed/disarmed via download. | |||||||||||||||||||||||
| It is easy to confuse this with original Concord, Main board as 55-750B printed on circuit board | |||||||||||||||||||||||
| Zones | 8 to 16 Hardwires, up to 8 Wireless (Now supports 16 Wireless Zones) | ||||||||||||||||||||||
| Transformer | Concord has 24 volt, Concord Express uses 16.5 volt | ||||||||||||||||||||||
| Batteries |
Note: Always have customer check what type of battery they have before having them buy a new one.
|
||||||||||||||||||||||
| Downloadable | Yes Note: Cannot be armed/disarmed through download | ||||||||||||||||||||||
|
Enable Downloading |
1. Press 9 + Master Code (“SYSTEM MENU” then “TIME/DATE”) 2. Press 2 + 0 3. Press 2 + # (“Display shows “DOWNLOADING ON”) 4. Press * + 4 + # |
||||||||||||||||||||||
| Panic Buttons |
A and 1 Police Panic B and 4 Medical Panic C and 7 Fire Panic |
||||||||||||||||||||||
| Away Arm | Press 3 (AWAY) + User Code | ||||||||||||||||||||||
| Stay Arm | 2 (STAY) + User Code | ||||||||||||||||||||||
| Instant Arm | Arm with 2 (STAY) or 3 (AWAY) + User Code then press 4 (NO DELAY) | ||||||||||||||||||||||
| Latchkey Arm | 2 (STAY) or 3 (AWAY) + User Code + 6 | ||||||||||||||||||||||
| Silent Arm | Press 5 then Arm with above steps for no beeps on keypad during Arming | ||||||||||||||||||||||
| Quick Exit | While Armed press D key to allow leaving without disarming for 2 minutes | ||||||||||||||||||||||
| Disarm | 1 + User Code | ||||||||||||||||||||||
| Silence Alarm | 1 + User Code, press * to view Alarm Memory | ||||||||||||||||||||||
| Reset Smoke | 1 + User Code twice | ||||||||||||||||||||||
| Check Status |
Press * key once for short status message, ** twice for Full Status (Short Status shows AC Power and Battery Status) |
||||||||||||||||||||||
| Bypass |
1. Arm system, press # + User Code (Keypad shows “ENTER Snsr”) 2. Enter Zone to bypass (01 to 24) (Keypad shows “Snsr XX BYPASSED”) |
||||||||||||||||||||||
| Force Bypass |
1. Open zone then arm system 2. Keypad will beep rapidly (Keypad shows “PROTEST”) 3. Press # (Keypad shows “Snsr XX BYPASSED”) 4. System will finish Arming |
||||||||||||||||||||||
| Set Time/Date |
1. Press 9 + Master Code + 0 0 (Keypad shows “SET TIME”) 2. Enter new 4-Digit Time (2PM = 1400, 4AM = 0400) 3. Press # to save, press B key (Keypad shows “SET DATE”) 4. Enter 6-digit Date (July 02 2000 would be 070200) 5. Press # to save, * + 4 + # to exit |
||||||||||||||||||||||
| Door Chimes | Press 7 + 1 to turn On or Off (Keypad shows “CHIME IS ON or OFF”) | ||||||||||||||||||||||
| Alarm Memory | Press 7 + 6, also an has Event Buffer but only viewed by downloading | ||||||||||||||||||||||
| Phone Test | 8 + Master Code + 2, press * after test finishes | ||||||||||||||||||||||
| Sensor Test |
1. Press 8 + Master Code + 3 2. Keypad shows “Armed to Sensor Test”, beeps every 60 seconds 3. Open Door or Window, move by motion 4. Press * to view any untested sensors 5. Press 1 + Master Code to end (Wireless motions require no movement for 4 minutes prior to testing) |
||||||||||||||||||||||
| Adjust Sounds |
1. Press and hold * and 0 until steady tone sounds 2. Press 1 to lower pitch, 2 to raise pitch 3. After 15 seconds tone will stop, keypad returns to normal |
||||||||||||||||||||||
| Adjust Display |
Press 9 + Master Code + 2 + 2 and enter below commands Press 0 + # to turn off keypad backlighting Press 1 + # for Low backlighting Press 2 + # for Medium backlighting Press 3 + # for Bright backlighting |
||||||||||||||||||||||
| Keyfob Buttons |
|
||||||||||||||||||||||
| Pager Signals |
Pagers sends Event Code + User or Sensor Number + Last 4-Digits of Account Example: If Account 1234 is Disarmed by Master Code pager sends 111 678 1234 |
||||||||||||||||||||||
| Event Codes |
|
||||||||||||||||||||||
| Sensor/Users |
|
||||||||||||||||||||||