Security Pro 4000 Program

GE / ITI / UC Caretaker Plus Program

Frequency

319.5 MHZ Range 1000 Feet Open Air

Downloading

For Toolbox download add Download number as Receiver Number and do phone
test or call panel while tech doing phone test, or use CS-4000 with Phone Test

Format

ITI Format, 4/2 2300 Hz, 4/2 1400 Hz (always use ITI)

Enter Program

1. Open Main Panel Cover by removing 2 bottom screws
2. Move Tamper switch to NORMAL setting, keypad shows “Program Mode”
(Opening cover may be enough by itself to enter programming)

Program Options

BYPASS	moves down through Program Fields
STATUS	moves up through Program Fields
COMMAND	enters a Program Field Enter data desired then COMMAND to save (Keypad blinks “OK”)
FIRE	exits Program Field

Exit Program

Set Tamper Switch back to RUN or close Panel Cover

Defaul Panel

Press and hold MEMORY CLEAR in panel for 3 seconds (only as last resort!)

Signal Strength

User Code + STATUS + 9 (tests signal strength)

Program
Fields

BYPASS moves forward

STATUS moves back

COMMAND enters and saves

FIRE exits

Phone Number

Up to 18 digits

Phone Format

ITI Format

(BYPASS or STAY to toggle)

Siren Time Out

Enter 06

(01 to 15) minutes)

Duress Code

Enter 99

(Duress = 1st 2-digits of code + 99)

Account Number

Enter last 5 digits of Account

(no letters)

Entry Delay 1

Enter 2-digits in seconds

(08 to 88 seconds)

Entry Delay 2

Enter 2-digits in minutes

(1 to 8 minutes)

Exit Delay

2-digit Exit Delay

(08 to 88 seconds)

Activity Timeout

Normally do not program

(01 to 24 hours)

House Code

Normally do not program

(001 to 254)

Freeze Temp

Normally do not program

(40 to 90 degrees)

Loop IS Nc

Normally do not program

(Sets Keypad Zone NO or NC)

Unit Number

Normally do not program

Touchpad Quiet

Quiets Keypad Beeps

(COMMAND toggles Yes/No)

Chime Display

Normally do not program

(COMMAND toggles Yes/No)

Send Test

Normally do not program

(Sends Zone Text to other keypads)

Load Test

Normally do not program

(I have no idea what this does)

Delete Text

Normally do not program

Program Sensor

Text Normally do not program

(See bottom of this page)

Learn Sensors

1. Press COMMAND to enter (Display shows “Learn Group _ _”)
2. Enter Group number (01-29, 32) then COMMAND again

Click HERE for complete list of Sensor Types

3. Display shows LEARN Sn01, to learn different Sensor press 01 to 32
4. If this is correct sensor press COMMAND, display reads “TRIP sn”
5. Trip tamper on sensor, speaker will say “SENSOR ONE OKAY, SENSOR TWO”
6. Learn another sensor within this group or FIRE to exit to “LEARN GROUP”
7. Press FIRE again to exit back to “LEARN SENSORS” display

Delete Sensors

1. Press COMMAND to enter

(Display shows “DELETE SnXX”)

2. Enter sensor to delete (01-29, 32)

3. Press COMMAND

(Display shows “DEL SnXX OK”)

4. Press FIRE again to exit back to “DELETE SENSORS” display

Click HERE for complete list of Sensor Types

Upper Sensors

Normally do not program

1. Press COMMAND to enter

2. Press STATUS/BYPASS to move UP/DOWN Sensor numbers

Press COMMAND to toggle ON/OFF

Upper Sensor Numbers

77 = Touchpad Tamper

78 = Freeze Sensor

79 = No Activity

80 = Keypad Fire

81 = Keypad Police

82 = Keypad Medical/Aux

83 = Phone Test

84 = Enable/Disable Openings

85 = Enable/Disable Closings

86 = Duress Alarm

87 = Force Arming

88 = Energy Saver Enable

89 = RF Touchpad Supervisory or Low Battery

90 = AC Power Failure

91 = Low Panel Battery

92 = Panel Tamper

93 = Auto Phone Test

94 = Wireless Receiver Failure

95 = CPU Back in Service (AC Restoral)

96 = Phone Failure

Learn Touchpad

1. Press COMMAND to enter	(Display shows “Press TO01 BYP”)
2. Press BYPASS on touchpad	(Display shows “Press TP02 BYP”)
3. Program next Touchpad or FIRE to exit to “LEARN TOUCHPAD” display (Anytime this section is entered all existing learned touchpads are erased)

Functions

(can only be enabled by CS-4000 except F22, normally not needed)

Function	Description	Default
F00	ON = Remote Phone Access Enabled	ON
F01	ON = Ring twice/Hang/Ring enabled	ON
F02	ON = Exterior Siren sounds 15 seconds after alarm	OFF
F03	ON = Toll Saver	ON
F04	ON = Low Battery reports	ON
F05	ON = Sensor Supervisory reports	ON
F06	ON = Dialer Aborts during alarm if disarmed	ON
F07	ON = Access Key Type * (OFF), or # (ON)	OFF
F11	ON = Hardwire interior siren sounds alarm	OFF
F12	ON = Alarm Restoral Reports	OFF
F13	ON = Low RF Battery Restoral Reports	OFF
F14	ON = Hourly Phone Test	OFF
F15	ON = Alarm Verification (2 zones must trip b4 report)	OFF
F16	ON = Trouble Beeps	OFF
F17	ON = 24 Hr Sensor Tamper causes Alarm	OFF
F21	ON = Immediate Trouble Beeps	OFF
F22	ON = DTMF Dialing	OFF
(This can be done at keypad by entering *022
F25	ON = Keyfob Arming	OFF
F32	ON = Energy Saver/No Delay	OFF
F33	ON = Downloader Access enabled	OFF

ITI Caretaker+ Alpha Zone Description Programming

(Each zone description can be up to 10 words or characters)

1. Use Stay or BYPASS to move to “PROGRAM SENSOR TEXT”

2. Press COMMAND to enter

(Display shows “Sn _ _”)

3. Enter 2 digit zone (01-29, 32)

(Display shows current description)

4. Press COMMAND

(Display shows “A 00” (first word))

5. Enter 1st 2-digit word

(see below listl)

6. Press COMMAND to save

(Display shows “B 00” (second word)

7. Enter 2nd 2-digit word then COMMAND to save

(Display shows “C 00” (Third word)

7. Continue until finished, press FIRE and display shows new complete Zone Description

8. Press BYPASS to move to next zone or FIRE to exit to “PROGRAM SENSOR TEXT”

(Use 00 to delete word or character, 27 inserts Space)


Word >	Entry	Word >	Entry
Area	40	Library	70
Attic	41	Living	71
Basement	42	Main	72
Bathroom	43	Master	73
Bedroom	44	Mat	74
Bottom	45	Medical	75
Breezeway	46	Motion	76
Cabinet	47	North	77
Carpet	48	Office	78
Closet	49	Panic	79
Den	50	Patio	80
Desk	51	Police	81
Dining	52	Pool	82
Door	53	Porch	83
Drawer	54	Rear	84
East	55	Room	85
Entry	56	Safe	86
Family	57	Screen	87
Fire	58	Second	88
First	59	Sensor	89
Floor	60	Shock	90
Freeze	61	Side	91
Front	62	Sliding	92
Gallery	63	Smoke	93
Garage	64	Sound	94
Hall	65	South	95
Heat	66	Stairs	96
Kitchen	67	Top	97
Laundry	68	West	98
Level	69	Window	99
Character >	Entry	Character >	Entry
Null	00	U	21
A	01	V	22
B	02	W	23
C	03	X	24
D	04	Y	25
E	05	Z	26
F	06	(SPACE)	27
G	07	‘ (Apostophe)	28
H	08	– (Dash)	29
I	09	0	30
J	10	1	31
K	11	2	32
L	12	3	33
M	13	4	34
N	14	5	35
O	15	6	36
P	16	7	37
Q	17	8	38
R	18	9	39
S	19
T	20

CS-4000 Commands

ACCT or ACCOUNT

<XX-XX>

Account Number (0 as 1st digit if 4-digit account)

ACCESS

<4-digits>

Programs Master Code

ALARMQ

Views last 6 events of Alarm history

ANS 1

Connects CS-4000 to Panel

BATTLIFE

<1 to 30>

Battery Life? in Hours

BYPASS or BYP

(00 to 16)

Bypasses Sensors

DELETE or DEL

(00 to 16)

Deletes Sensors

DURESS

<00 to 99>

Hostage/Duress Code (usually 99)

ENTRY

<8 to 88>

Entry Delay (seconds)

EXIT

<8 to 88>

Exit Delay (seconds)

GROUP

Changes Zone type (Commander 17 2.6 only)

Freeze	GROUP	<zone>	01 L
Fire	GROUP	<zone>	02 D
Delay	GROUP	<zone>	04 L
Instant	GROUP	<zone>	05 L
Interior Inst Follower	GROUP	<zone>	06 L
Interior Follower	GROUP	<zone>	06 I
Silent Police Panic	GROUP	<zone>	12 A
Audible Medical Panic	GROUP	<zone>	01 B

HOUSE

<1 to 255>

Views House Code

INIT

<00 to 16>

Initializes Sensors

MACCESS

<2 to 6> <4 digits>

Programs Secondary Codes
(Commander 8 only has 1 secondary Code)

OPTION

<20 to 27> <ON or OFF>

Turns Functions ON/OFF (xx = 20 to 27)

F20 ON = Enable Interrogator	OFF = Disables
F21 ON = DC Power Monitored	OFF = Not Monitored
F22 ON = Dialing Format	OFF = Pulse
F23 ON = Retain O/C only	OFF = Retain All Events
F24 ON = Hardwire Loop NO	OFF = Normally Closed OFF
F26 ON = Quick Disarm Enabled	OFF = Disabled
F27 ON = Panel Alarm Mute	OFF = Alarm Output Normal
Note: F20 and F27 must be ON for Interrogator

PLOCK

???? %XXXXXXXX

Changes Installer Code
???? = Old Installer Code
XXXX = New Installer Code Twice

PFORMAT

<0 to 2>

Report Format (0=ITI, 1=4×2, 1400hz, 2=4/2, 2300hz)

PHONE

<7 to 4 digits>

Primary Receiver (D = Pause)

PHONE2

<7 to 4 digits>

Secondary Receiver (Commander 17 only)

PLEVEL

<1 to 3<

Changes Arming Level
PLEVEL 1 = Disarm
PLEVEL 2 = Arm Home
PLEVEL 3 = Arm Away

RECALL

Has panel disconnect then call back

REL

Releases Panel from CS-4000

SIREN

<1 to 9>

Siren Timeout in Minutes

STIME

<hh:mm>

Supervisory Report Time

UPD

Sends updated programming to panel

ZONES

Lists all Zones including Panics & Supervisory