Napco XP600 Program

Enter Program * + 8 + 4567, ARMED light turns ON, SYSTEM will flash
Exit Program # + * + 8 + Installer Code
Move to Location # + 2-digit location
Clear Location Press
Default Panel 1. Power system down, jumper terminal 15 (PGM) to terminal 3 (ZONE 1)
2. Power up after 10 seconds ARMED, READY SYSTEM flash
3. Power back down, return wiring back to normal then power up again
(If this does not work system is locked out)
Hex Digits A=* 1, B=* 2, C=* 3, D=* 4, E=* 5, F=* 6
#00 Entry/Exit Zones (Toggle Options ON/OFF)
Default
ON
OFF
OFF
OFF
OFF
OFF 		I_ON_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6 		ON = Zone is a Delay Entry/Exit Zone
OFF= Zone is not Delay Entry/Exit Zone
#01 Home/Away with Delay Zones (Auto-Bypasses Motion Zones)
Default
OFF
OFF
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6 		ON = Zone is Home/Away with Delay Zone
OFF= Zone is not Home/Away with Delay Zone
#02 Entry/Exit Follower Zones (Enable for any Motion Zones)
Default
OFF
OFF
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6 		ON = Zone is Entry/Exit Follower Zone
OFF= Zone is not Entry/Exit Follower Zone
#03 Auto Bypass Re-Entry Zones (Normally Leave all OFF)
Default
OFF
OFF
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6 		ON = Zone Fault allows Arming, Arms when Zone Restores
OFF= Zone Fault does not allow Arming
#04 24 Hour Zones (Fire/Panic) (Toggle 1 to 4 ON for Smoke/Panic Zones)
Default
OFF
OFF
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6 		ON = Zone is 24 Hour Zone
OFF= Zone is not 24 Hour Zone
#05 40 ms Loop Response (Normally turn all lights ON)
Default
OFF
OFF
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6 		ON = Zone Response 40 ms
OFF= Zone Response 750 ms
#06 Open Circuit Zones (Normally turn all lights ON)
Default
OFF
OFF
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6 		ON = Zone is Normally Open Zone
OFF= Zone is Normally Closed Zone
#07 Burglary Steady Output (Normally turn all lights ON)
Default
ON
ON
ON
ON
ON
ON 		I_ON_I
I_ON_I
I_ON_I
I_ON_I
I_ON_I
I_ON_I 		Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6 		ON = Zone Alarm activates Siren Output
OFF= Zone Alarm is Silent

(If Silent Panic or Holdup toggle zone light OFF)

#08 PGM Output (Normally turn all lights ON)
Default
ON
ON
ON
ON
ON
ON 		I_ON_I
I_ON_I
I_ON_I
I_ON_I
I_ON_I
I_ON_I 		Zone 1
‘
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6 		ON = PGM Activates on Zone Trip until Reset
OFF= PGM not Enabled on Zone Trip
#09 Selective Bypass << This section may not exist in older versions
Default
ON
ON
ON
ON
ON
ON 		I_ON_I
I_ON_I
I_ON_I
I_ON_I
I_ON_I
I_ON_I 		Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6 		ON = Zone Bypassing Allowed
OFF= Zone Bypassing Not Allowed
#10 Exit Delay I_0_I_6_I_0_I (001 to 255 Seconds)
#11 Entry Delay I_0_I_3_I_0_I (001 to 255 Seconds)
#12 Bell/Siren Timeout I_0_I_0_I_6_I (001 to 255 Minutes)
#13 Fire (Pulsed Timeout) I_0_I_0_I_0_I (000 to 255 Minutes, 000=Disabled)
#14 Test Timer Interval I_0_I_0_I_1_I (001 to 255 Days)
#15 Line Cut Time (Phone Monitor) I_0_I_0_I_0_I (010 to 255 Seconds 000=Disable)
#16 Wireless Supervisory Timer I_1_I_2_I (01 to 26 in Hours)
#17 Wireless Smoke Supervisory Timer I_8_I (01 to 8 in Hours)
#18 Test Timer Offset I_1_I_2_I (01 to 23 in Hours)
#20 Keypad Features 1 (Toggle Options ON/OFF)
Default
OFF
OFF
ON
OFF 		I_ON_I
I_ON_I
I_ON_I
I_ON_I 		Keypad Panic 2 Enabled (Can be Fire Panic I guess)
Keypad Medical Enabled
Keypad Police Panic Enabled
Ambush is 6th User Code
#21 Keypad Features 2 (Toggle Options ON/OFF)
Default
ON
OFF
ON
OFF 		I_ON_I
I_ON_I
I_ON_I
I_OFF_I 		Keypad Panic Audible
Entry/Entry Delay with Urgency Beeps
Display Bypass while Armed
Disable Keypad Keypress Beeps
#22 Miscellaneous Features 1 (Toggle Options ON/OFF)
Default
OFF
ON
ON
OFF 		I_OFF_I
I_ON_I
I_ON_I
I_ON_I 		Abort Delay
Easy Arm/Easy Exit (Quick Arm/Quick Exit)
Swinger Shutdown Enabled
Bell on Phone Line Cut if Armed
#23 PGM Features 1 (Toggle Options ON/OFF)
Default
OFF
ON
ON
OFF 		I_OFF_I
I_OFF_I
>
I_OFF_I
I_OFF_I 		Audio Verification (If using Variphone 2-way Board)
Access Output to PGM for 5 seconds with FUNCTION + 3
PGM Follows Keypad Sounder
Keyfob/Keyswitch Chirp (1 Chirp if Armed, 2 Chirps if Disarmed)
#24 PGM Features 2 (Toggle Options ON/OFF)
Default
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		Reserved (Leave OFF)
PGM Activates on AUX Alarm
PGM Activates on Panic Alarm
PGM Activates during Test Timer Report
#25 PGM Features 3 (Toggle Options ON/OFF)
Default
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		PGM Activates 15 Minutes after AC Fail
PGM Activates on Low Battery
PGM Activates on a Trouble Condition
PGM Activates if System Armed
#26 Miscellaneous Features 2 (Toggle Options ON/OFF)
Default
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		Momentary Keyswitch Arming on Zone
Reserved (Leave OFF)
Inhibit Fail to Communicate Display
Inhibit Low Battery Display
#30 Account 1 (Last 4 of Account) I_ _I_ _I_ _I_ _I
#31 Receiver Phone 1 (Up to 12 Digits) I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
erases Digits
4 Second Pause = D (* 4)
#32 Receiver Format
Default
4 I_6_I
0 = Disabled
1 = Ademco Slow
2 = Radionics Slow
3 = Silent Knight Fast 		4 = Universal High Speed
5 = Reserved
6 = Contact ID
7 = Pager
#33 Receiver 1 Options (Toggle Options ON/OFF)
Default
ON
OFF
OFF
OFF 		I_ON_I
I_OFF_I
I_OFF_I
I_OFF_I 		2300 Handshake/Kissoff
Sumcheck
Single Digit
No Handshake/Pager Enabled
#34 Zone Report Enable Phone 1 (Toggle Options ON/OFF)
Default
ON
ON
ON
ON
>
ON
ON 		I_ON_I
I_ON_I
I_ON_I
I_ON_I
I_ON_I
I_ON_I 		Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6 		ON = Zone Alarms sent to Phone 1
OFF= Zone Alarms not sent to Phone 1
#35 Zone Restore Phone 1 (Toggle Options ON/OFF)
Default
OFF
OFF
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6 		ON = Zone Restorals sent to Phone 1
OFF= Zone Restorals not sent to Phone 1
#36 System Reporting Phone 1 (Toggle Options ON/OFF)
Default
OFF
OFF
ON
OFF 		I_ON_I
I_ON_I
I_ON_I
I_OFF_I 		Keypad Fire Panic Report Enable
Keypad Medical Panic Report Enable
Keypad Police Panic Report Enable
Test Timer Report Enable
#37 System Reporting Phone 1 (Toggle Options ON/OFF)
Default
OFF
ON
OFF
ON 		I_ON_I
I_ON_I
I_ON_I
I_ON_I 		AC Fail Report Enable (15 Min Delay)
Low Battery Report Enable
Trouble Report Enable
Fire Report Enable
#38 System Restore Report Phone 1 (Toggle Options ON/OFF)
Default
OFF
OFF
OFF
OFF 		I_ON_I
I_OFF_I
I_OFF_I
I_ON_I 		AC Fail Restore Report Enable (15 Min Delay)
Low Battery Restore Report Enable
Trouble Restore Report Enable
Fire Restore Report Enable
#39 Open/Close Report Phone 1 (Toggle Options ON/OFF)
Default
OFF
OFF
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		User 1 Reporting
User 2 Reporting
User 3 Reporting
User 4 Reporting
User 5 Reporting
User 6 Reporting 		ON= Opening/Closings for this User Enabled
OFF= Opening/Closings for this User Disabled
#40 Account 2 I_ _I_ _I_ _I_ _I
#41 Receiver Phone 2 (12 Digits) I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
(Do not program Pager here, use Phone 3 instead)
#42 Receiver Format Phone 2 I_ _I
#43 Receiver 2 Options (Toggle Options ON/OFF)
Default
ON
OFF
OFF
OFF 		I_ON_I
I_OFF_I
I_OFF_I
I_OFF_I 		2300 Handshake/Kissoff
Sumcheck
Single Digit
No Handshake/Pager Enabled
#44 Dialing Prefix Phone 1, 2 & 3 I_ _I_ _I_ _I_ _I
Use if needing to dial 9, enter 9 +
#45 Communicator Features 1 (Toggle Options ON/OFF)
Default
ON
ON
OFF
OFF 		I_ON_I
I_ON_I
I_OFF_I
I_OFF_I 		Communicator Enabled
DTMF with Rotary Backup
DTMF Only
Backup to Telco 2
#46 Communicator Features 2 (Toggle Options ON/OFF)
Default
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		No Dial Tone Detection
2:1 Rotary Dialing
Backup if Less than 4 Attempts
Reserved
#47 Pager Leading Digits (30 Digits) I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
(this is extra info that can show up on the pager screen)
#48 Pager Trailing Digits (10 Digits) I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
(this is extra info that can show up on the pager screen)
#49 Pager Operation (Toggle Options ON/OFF)
Default
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		Skip Alarm Data (Only send Opening/Closings)
Reserved
Reserved
Reserved
#50 Account 3 I_ _I_ _I_ _I_ _I
#51 Receiver Phone 3 (12 Digits) I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
If using Pager add pauses (* 4) after number (3 should work)
#52 Receiver Format Phone 3 I_ _I
#53 Receiver 3 Options (Toggle Options ON/OFF)
Default
ON
OFF
OFF
OFF 		I_ON_I
I_OFF_I
I_OFF_I
I_ON_I 		2300 Handshake/Kissoff
Sumcheck
Single Digit
No Handshake/Pager Enabled
#54 Zone Report Phone 3 (Toggle Options ON/OFF)
Default
OFF
OFF
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6 		ON = Zone Alarms sent to Phone 3
OFF= Zone Alarms not sent to Phone 3
#55 Zone Restore Phone 3 (Toggle Options ON/OFF)
Default
OFF
OFF
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6 		ON = Zone Restorals sent to Phone 3
OFF= Zone Restorals not sent to Phone 3
#56 System Report Phone 3 (Toggle Options ON/OFF)
Default
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		Keypad Fire Panic Report Enable
Keypad Medical Panic Report Enable
Keypad Police Panic Report Enable
Test Timer Report Enable
#57 System Report Phone 3 (Toggle Options ON/OFF)
Default
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		AC Fail Report Enable (15 Min Delay)
Low Battery Report Enable
Trouble Report Enable
Fire Report Enable
#58 System Restore Phone 3 (Toggle Options ON/OFF)
Default
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		AC Fail Restoral Report Enable (15 Min Delay)
Low Battery Restoral Report Enable
Trouble Restoral Report Enable
Fire Restoral Report Enable
#59 Open/Close Reports Phone 3 (Toggle Options ON/OFF)
Default
OFF
OFF
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		User 1 Reporting Enable
User 2 Reporting Enable
User 3 Reporting Enable
User 4 Reporting Enable
User 5 Reporting Enable
User 6 Reporting Enable
#60 4/2 Zone Report Codes
Default
3
3
3
3
3
3 		I_3_I
I_3_I
I_3_I
I_3_I
I_3_I
I_3_I 		Zone 1 Alarm Report Code (This is 1st digit, 2nd digit sent automatically)
Zone 2 Alarm Report Code
Zone 3 Alarm Report Code
Zone 4 Alarm Report Code
Zone 5 Alarm Report Code
Zone 6 Alarm Report Code
#61 Contact ID Report Codes
Default
3
3
3
3
3
3 		I_3_I
I_3_I
I_3_I
I_3_I
I_3_I
I_3_I
Zone 1 Alarm Report Code
Zone 2 Alarm Report Code
Zone 3 Alarm Report Code
Zone 4 Alarm Report Code
Zone 5 Alarm Report Code
Zone 6 Alarm Report Code  
Contact ID Report Codes (1st digit, 2nd is Zone)
1 = Reserved
2 = Panic
3 = Burglary
4 = Holdup
5 = General Alarm 		6 = Reserved
7 = Gas Alarm
8 = Heat Alarm
9 = Reserved
A = Auxiliary
B = 24 Hr Alarm
#62 Zone Codes
Default
E
F 		I_0_I
I_0_I 		Zone 1, 2, 3, 4, 5 & 6 Restore Code
Zone 1, 2, 3, 4, 5 & 6 Trouble Code
#63 System Report Codes (Auto-reports regardless of report code if Contact ID is used)
Default
11
23
21
FF
F9
F8
F1
11 		I_1_I_1_I
I_2_I_3_I
I_2_I_1_I
I_F_I_F_I
I_F_I_9_I
I_F_I_8_I
I_F_I_1_I
I_1_I_1_I 		Keypad Fire Panic (7/F & *)
Keypad Aux Panic (8/A & *)
Keypad Police Panic (97P & *)
Test Timer
AC Failure
Low Battery
Trouble (Fire Trouble/Receiver Fail/Tamper/Wireless Low Bat)
Fire Zone
#64 System Restore Code
Default
E I_0_I (Receiver Fail/Tamper/Wireless Low Bat)
#65 Open/Close Code
Default
C
B 		I_0_I
I_0_I 		Closing Report Code
Opening Report Code
#66 Ambush/Duress Code
Default
22 I_2_I_2_I
#67 Enhanced Communication Phone 1 (Toggle Options ON/OFF)
Default
OFF
OFF
OFF
OFF 		I_ON_I
I_OFF_I
I_OFF_I
I_OFF_I 		Opening After Alarm (Enable Cancel)
Conditional Closing
Reserved
Reserved
#68 Enhanced Communication Phone 3 (Toggle Options ON/OFF)
Default
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		Opening After Alarm
Conditional Closing
Reserved
Reserved
Wireless Programming (Wireless AND Hardwired devices can occupy the same zone)
Sample Sensor
Serial Number Point
#71 Zone 1 Wireless Serial Number I_ _I_ _I_ _I_ _I_ _I_ _I : I_ _I I_ _I
Internal Reed = Point 1
Program sensor by entering 7-Digit Serial # + Point External Sensors = Point 2
Strap off External Terminals if using Internal Point Smoke Detector = Point 1
Motion Detector = Point 1
Glassbreaks = Point 1
#72 Zone 2 Wireless Serial Number I_ _I_ _I_ _I_ _I_ _I_ _I : I_ _I I_ _I
#73 Zone 3 Wireless Serial Number I_ _I_ _I_ _I_ _I_ _I_ _I : I_ _I I_ _I
#74 Zone 4 Wireless Serial Number I_ _I_ _I_ _I_ _I_ _I_ _I : I_ _I I_ _I
#75 Zone 5 Wireless Serial Number I_ _I_ _I_ _I_ _I_ _I_ _I : I_ _I I_ _I
#76 Zone 6 Wireless Serial Number I_ _I_ _I_ _I_ _I_ _I_ _I : I_ _I I_ _I
Aux
Serial Number 1 2
#81 Keyfob 1 Serial Number     I_ _I_ _I_ _I_ _I_ _I_ _I_ _I       I_ _I_ _I
#82 Keyfob 2 Serial Number I_ _I_ _I_ _I_ _I_ _I_ _I_ _I I_ _I_ _I
#83 Keyfob 3 Serial Number I_ _I_ _I_ _I_ _I_ _I_ _I_ _I I_ _I_ _I
#84 Keyfob 4 Serial Number I_ _I_ _I_ _I_ _I_ _I_ _I_ _I I_ _I_ _I
Top 2 buttons = ARM & DISARM, bottom 2 = AUX 1 & 2 can be programmed for several functions
1 = Police Panic
2 = Aux/Medical
3 = Bell ON
4 = PGM Output
5 = Access on PGM
7 = FULLY ARM (Use ON key + Selected AUX key programmed as 7
8 = STAY ARM (Use ON key + Selected AUX key programmed as 8
Serial Number Point
#85 Wireless Smoke 1 Serial Number     I_ _I_ _I_ _I_ _I_ _I_ _I : I_ _I       I_ _I
#86 Wireless Smoke 2 Serial Number I_ _I_ _I_ _I_ _I_ _I_ _I : I_ _I I_ _I
#87 Wireless Smoke 3 Serial Number I_ _I_ _I_ _I_ _I_ _I_ _I : I_ _I I_ _I
#88 Zone 5 Wireless Serial Number I_ _I_ _I_ _I_ _I_ _I_ _I : I_ _I I_ _I
#90 Download Phone Number     I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
(Press to Blank Out)
#91 Ring Count
Default
09 I_2_I_2_I (00 to 15)
#92 Downloading Features (Toggle Options ON/OFF)
Default
ON
OFF
OFF
OFF 		I_ON_I
I_ON_I
I_ON_I
I_OFF_I 		Ring Method (# of Rings)
Answering Machine Over-Ride
FUNCTION + 6 Download Enable
Wireless Signal Strength Test Mode
#93 Auto Download ID # (Do not Program)
Default
I_ _I_ _I
#94 Installer Code (Leave this Default Please)
Default
4567 I_4_I_5_I_6_I_7_I
#95 User 1 Master Code
Default
1234 I_ _I_ _I_ _I_ _I
#96 Dealer Options 1 (Toggle Options ON/OFF)
Default
OFF
ON
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		Dealer Code (Panel) Lockout Enable
User Code 1 Lockout
UL Household Fire
Fire Trouble on Fire LED
#97 Dealer Options 2 (Toggle Options ON/OFF)
Default
OFF
OFF
OFF
OFF 		I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I 		International Dialing Protocol
Invert Bell Output
System Trouble Auto Reset
User 1 Code Program Only
#98 Dial Attempts
Default
9 I_9_I (1 to F)