Napco XP 400 Program – CMS Tech Help

Napco XP400 Keypad

Enter Program	* + 8 + 4567, ARMED light turns ON, SYSTEM will flash and keypad will beep 4 times.
Exit Program	# + * + 8 + Installer Code
Move to Location	# + 2-digit location
Clear Location	Press
Default Panel	1. Power system down, jumper terminal 15 (PGM) to terminal 3 (ZONE 1) 2. Power up after 10 seconds ARMED, READY SYSTEM flash 3. Power back down, return wiring back to normal then power up again (If this does not work system is locked out)
Hex Digits	A=* 1 B=* 2 C=* 3 D=* 4 E=* 5 F=* 6

#00	Entry/Exit Zones (Toggle Options ON/OFF)
	Default
	ON OFF OFF OFF	I_ON_I I_OFF_I I_OFF_I I_OFF_I	Zone 1 Zone 2 Zone 3 Zone 4	ON = Zone is a Delay Entry/Exit Zone OFF= Zoone is not Delay Entry/Exit Zone
#01	Home/Away with Delay Zones (Auto-Bypasses Motion Zones)
	Default
	OFF OFF OFF OFF	I_OFF_I I_OFF_I I_OFF_I I_OFF_I	Zone 1 Zone 2 Zone 3 Zone 4	ON = Zone is Home/Away with Delay OFF= Zone is not Home/Away with Delay
#02	Entry/Exit Follower Zones (Enable for any Motion Zones)
	Default
	OFF OFF OFF OFF	I_OFF_I I_OFF_I I_OFF_I I_OFF_I	Zone 1 Zone 2 Zone 3 Zone 4	ON = Zone is Entry/Exit Follower Zone OFF= Zone is not Entry/Exit Follower Zone
#03	Auto Bypass Re-Entry Zones (Normally turn all lights OFF)
	Default
	OFF OFF OFF OFF	I_OFF_I I_OFF_I I_OFF_I I_OFF_I	Zone 1 Zone 2 Zone 3 Zone 4	ON = Zone is Entry/Exit Follower Zone OFF= Zone is not Entry/Exit Follower Zone
#04	24 Hour Zones (Toggle 1 to 4 ON for Panic Zones)
	Default
	OFF OFF OFF OFF	I_OFF_I I_OFF_I I_OFF_I I_OFF_I	Zone 1 Zone 2 Zone 3 Zone 4	ON = Zone is 24 Hour Zones OFF= Zone is not 24 Hour Zones (This system does NOT support Smoke Detectors)
#05	40 ms Loop Response (Normally turn all lights OFF)
	Default
	OFF OFF OFF OFF	I_OFF_I I_OFF_I I_OFF_I I_OFF_I	Zone 1 Zone 2 Zone 3 Zone 4	ON = Zone has 40 ms Loop Response OFF= Zone has Normal Loop Response
#06	Open Circuit Zones (Normally turn all lights OFF)
	Default
	OFF OFF OFF OFF	I_OFF_I I_OFF_I I_OFF_I I_OFF_I	Zone 1 Zone 2 Zone 3 Zone 4	ON = Zone is a Normally Open Zone OFF= Zone is a Normally Closed Zone
#07	Burglary Steady Output (Normally turn all lights ON)
	Default
	ON ON ON ON	I_ON_I I_ON_I I_ON_I I_ON_I	Zone 1 Zone 2 Zone 3 Zone 4	ON = Zone Alarm is Steady Siren Output OFF= Alarm is Silent (If Silent Panic or Holdup toggle zone light OFF)
#08	PGM Output (Normally turn all lights ON)
	Default
	ON ON ON ON	I_ON_I I_ON_I I_ON_I I_ON_I	Zone 1 Zone 2 Zone 3 Zone 4	ON = PGM Enabled on Zone Trip until Reset OFF= PGM not Enabled on Zone Trip

#10	Exit Delay	I_0_I_6_I_0_I	(001 to 255 Seconds)
#11	Entry Delay	I_0_I_3_I_0_I	(001 to 255 Seconds)
#12	Bell/Siren Timeout	I_0_I_0_I_6_I	(001 to 255 Minutes)
#13	Reserved	Do Not Program
#14	Test Timer Interval	I_0_I_0_I_1_I	(001 to 255 Days)
#15	Line Cut Time (Phone Monitor)	I_0_I_0_I_0_I	(010 to 255 Seconds 000=Disable)
#16	Wireless Supervisory Timer	I_1_I_2_I	(01 to 26 in Hours)

#20	Keypad Features 1 (Toggle Options ON/OFF)
	Default
	OFF OFF ON OFF	I_ON_I I_ON_I I_ON_I I_ON_I	Keypad Panic 2 Enabled (Can be Fire Panic I guess) Keypad Medical Enabled Keypad Police Panic Enabled Ambush is 4th User Code
#21	Keypad Features 2 (Toggle Options ON/OFF)
	Default
	ON OFF ON OFF	I_ON_I I_ON_I I_ON_I I_OFF_I	Keypad Panic Audible Entry Delay with Urgency Beeps Display Bypass while Armed Disable Keypad Keypress Beeps
#22	Miscellaneous Features 1 (Toggle Options ON/OFF)
	Default
	OFF ON ON OFF	I_OFF_I I_ON_I I_ON_I I_ON_I	Abort Delay Easy Arm/Easy Exit (Quick Arm/Quick Exit) Swinger Shutdown Enabled Bell on Phone Line Cut if Armed
#23	PGM Features 1 (Toggle Options ON/OFF)
	Default
	OFF OFF OFF OFF	I_OFF_I I_OFF_I I_OFF_I I_OFF_I	Audio Verification (If using Variphone 2-way Board) Access Output to PGM for 5 seconds with FUNCTION + 3 PGM Follows Keypad Sounder Keyfob/Keyswitch Chirp (1 Chirp if Armed, 2 Chirps if Disarmed)
#24	PGM Features 2 (Toggle Options ON/OFF)
	Default
	OFF OFF OFF OFF	I_OFF_I I_OFF_I I_OFF_I I_OFF_I	Reserved (Leave OFF) PGM Activates on AUX Alarm PGM Activates on Panic Alarm PGM Activates during Test Timer Report
#25	PGM Features 3 (Toggle Options ON/OFF)
	Default
	OFF OFF OFF OFF	I_OFF_I I_OFF_I I_OFF_I I_OFF_I	PGM Activates 15 Minutes after AC Fail PGM Activates on Low Battery PGM Activates on a Trouble Condition PGM Activates if System Armed
#26	Miscellaneous Features 2 (Toggle Options ON/OFF)
	Default
	OFF OFF OFF OFF	I_OFF_I I_OFF_I I_OFF_I I_OFF_I	Momentary Keyswitch Arming on Zone Reserved (Leave OFF) Inhibit Fail to Communicate Display Inhibit Low Battery Display

#30	Account 1 (Last 4 of Account) I_ _I_ _I_ _I_ _I
#31	Receiver Phone 1 (Up to 12 Digits) I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I erases Digits 4 Second Pause = D (* 4)

#32

Receiver Format

Default

I_6_I

0 = Disabled	4 = Universal High Speed
1 = Ademco Slow	5 = Reserved
2 = Radionics Slow	6 = Contact ID
3 = Silent Knight Fast	7 = Pager

#33

Receiver 1 Options (Toggle Options ON/OFF)

Default

ON
OFF
OFF
OFF

I_ON_I
I_OFF_I
I_OFF_I
I_OFF_I

2300 Handshake/Kissoff
Sumcheck
Single Digit
No Handshake/Pager Enabled

#34

Zone Report Enable Phone 1 (Toggle Options ON/OFF)

Default

ON
ON
ON
ON

I_ON_I
I_ON_I
I_ON_I
I_ON_I

Zone 1
Zone 2
Zone 3
Zone 4

ON = Zone Alarms sent to Phone 1
OFF= Zone Alarms not sent to Phone 1

#35

Zone Restore Phone 1 (Toggle Options ON/OFF)

Default

OFF
OFF
OFF
OFF

I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I

Zone 1
Zone 2
Zone 3
Zone 4

ON = Zone Restorals sent to Phone 1
OFF= Zone Restorals not sent to Phone 1

#36

System Reporting Phone 1 (Toggle Options ON/OFF)

Default

OFF
OFF
ON
OFF

I_ON_I
I_ON_I
I_ON_I
I_OFF_I

Keypad Fire Panic Report Enable
Keypad Medical Panic Report Enable
Keypad Police Panic Report Enable
Test Timer Report Enable

#37

System Reporting Phone 1 (Toggle Options ON/OFF)

Default

OFF
ON
OFF
OFF

I_ON_I
I_ON_I
I_ON_I
I_OFF_I

AC Fail Report Enable (15 Min Delay)
Low Battery Report Enable
Trouble Report Enable
Reserved

#38

System Restore Report Phone 1 (Toggle Options ON/OFF)

Default

OFF
OFF
OFF
OFF

I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I

AC Fail Report Enable (15 Min Delay)
Low Battery Report Enable
Trouble Report Enable
Reserved

#39

Open/Close Report Phone 1 (Toggle Options ON/OFF)

Default

OFF
OFF
OFF
OFF

I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I

User 1 Reporting
User 2 Reporting
User 3 Reporting
User 4 Reporting

ON= Opening/Closings for this User Enabled
OFF= Opening/Closings for this User Disabled

#40	Account 2	I_ _I_ _I_ _I_ _I
#41	Receiver Phone 2 (12 Digits)	I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I Do not program Pager here, use Phone 3 instead
#42	Receiver Format Phone 2	I_ _I

#43	Receiver 2 Options (Toggle Options ON/OFF)
	Default
	ON OFF OFF OFF	I_ON_I I_OFF_I I_OFF_I I_OFF_I	2300 Handshake/Kissoff Sumcheck Single Digit No Handshake/Pager Enabled

#44

Dialing Prefix Phone 1, 2 & 3

I_ _I_ _I_ _I_ _I
Use if needing to dial 9, enter 9 +

#45	Communicator Features 1 (Toggle Options ON/OFF)
	Default
	ON ON OFF OFF	I_ON_I I_ON_I I_OFF_I I_OFF_I	Communicator Enabled DTMF with Rotary Backup DTMF Only Backup to Telco 2
#46	Communicator Features 2 (Toggle Options ON/OFF)
	Default
	OFF OFF OFF OFF	I_OFF_I I_OFF_I I_OFF_I I_OFF_I	No Dial Tone Detection 2:1 Rotary Dialing Backup if Less than 4 Attempts Reserved

#50	Account 3 (Do not Program)	I_ _I_ _I_ _I_ _I
#51	Receiver Phone 3 (Up to 12 digits) I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I Note: If using Pager add pauses (* 4) after phone number (at least 3 should work)
#52	Receiver Format Phone 3	I_ _I Enter 7 here if using Pager

#53

Receiver 3 Options (Toggle Options ON/OFF)

Default

ON
OFF
OFF
OFF

I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I

2300 Handshake/Kissoff
Sumcheck
Single Digit
No Handshake/Pager Enabled

#54

Zone Report Phone 3 (Toggle Options ON/OFF)

Default

OFF
OFF
OFF
OFF

I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I

Zone 1
Zone 2
Zone 3
Zone 4

ON = Zone Alarms sent to Phone 3
OFF= Zone Alarms not sent to Phone 3

#55

Zone Restore Phone 3 (Toggle Options ON/OFF)

Default

OFF
OFF
OFF
OFF

I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I

Zone 1
Zone 2
Zone 3
Zone 4

ON = Zone Restorals sent to Phone 3
OFF = Zone Restorals not sent to Phone 3

#56

System Report Phone 3 (Toggle Options ON/OFF)

Default

OFF
OFF
OFF
OFF

I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I

Keypad Fire Panic Report Enable
Keypad Medical Panic Report Enable
Keypad Police Panic Report Enable
Test Timer Report Enable

#57

System Report Phone 3 (Toggle Options ON/OFF)

Default

OFF
OFF
OFF
OFF

I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I

AC Fail Report Enable (15 Min Delay)
Low Battery Report Enable
Trouble Report Enable
Reserved

#58

System Restore Phone 3 (Toggle Options ON/OFF)

Default

OFF
OFF
OFF
OFF

I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I

AC Fail Report Enable (15 Min Delay)
Low Battery Report Enable
Trouble Report Enable
Reserved

#59

Open/Close Reports Phone 3 (Toggle Options ON/OFF)

Default

OFF
OFF
OFF
OFF

I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I

User 1 Reporting
User 2 Reporting (Turn this section ON for if using Pager)
User 3 Reporting
User 4 Reporting

#60

Zone Report Codes (Only used if 4/2 format is selected in section 32)

Default

3
3
3
3

I_3_I
I_3_I
I_3_I
I_3_I

Zone 1 Alarm Report Code (This is 1st digit, 2nd digit sent automatically)
Zone 2 Alarm Report Code
Zone 3 Alarm Report Code
Zone 4 Alarm Report Code

#61

Contact ID Report Codes (Only used if Contact ID is selected in section 32)

Default

3
3
3
3

I_3_I
I_3_I
I_3_I
I_3_I

Zone 1 Alarm Report Code
Zone 2 Alarm Report Code
Zone 3 Alarm Report Code
Zone 4 Alarm Report Code

Contact ID Report Codes (1st digit, 2nd is Zone)
1 = Reserved	6 = Reserved
2 = Panic	7 = Gas Alarm
3 = Burglary	8 = Heat Alarm
4 = Holdup	9 = Reserved
5 = General Alarm	A = Auxiliary
	B = 24 Hr Alarm

#62

Zone Restore/Trouble Codes

Default

E
F

I_0_I
I_0_I

Zone 1, 2, 3, 4 Restore Code
Zone 1, 2, 3, 4 Trouble Code

#63

System Report Codes (Auto-reports regardless of report code if Contact ID is used)

Default

11
23
21
FF
F9
F8
F1

I_1_I_1_I
I_2_I_3_I
I_2_I_1_I
I_0_I_0_I
I_F_I_9_I
I_F_I_8_I
I_F_I_1_I

Keypad Fire Panic (7/F & *)
Keypad Aux Panic (8/A & *)
Keypad Police Panic (97P & *
Test Timer
AC Failure
Low Battery
Trouble (Receiver Fail/Tamper/Wireless Low Bat)

#64

System Restore Code

Default

I_0_I

(Receiver Fail/Tamper/Wireless Low Bat)

#65

Open/Close Code

Default

C
B

I_0_I
I_0_I

Closing Report Code
Opening Report Code

#66

Ambush/Duress Code

Default

I_2_I_2_I

#67

Enhanced Communication Phone 1 (Toggle Options ON/OFF)

Default

OFF
OFF
OFF
OFF

I_ON_I
I_OFF_I
I_OFF_I
I_OFF_I

Opening After Alarm (Enable Cancel)
Conditional Closing
Reserved
Reserved

#68

Enhanced Communication Phone 3 (Toggle Options ON/OFF)

Default

OFF
OFF
OFF
OFF

I_OFF_I
I_OFF_I
I_OFF_I
I_OFF_I

Opening After Alarm
Conditional Closing
Reserved
Reserved

Wireless Programming (Wireless AND Hardwired devices can occupy the same zone)

Sample Sensor

Serial Number

Point

#71

Zone 1 Wireless Serial Number

I_ _I_ _I_ _I_ _I_ _I_ _I : I_ _I

I_ _I

	Internal Reed	= Point 1
Program sensor by entering 7-Digit Serial # + Point	External Sensors	= Point 2
Strap off External Sensor Terminals if using Internal Point	Smoke Detector	= Point 1
	Motion Detector	= Point 1
	Glassbreaks	= Point 1

#72

Zone 2 Wireless Serial Number

I_ _I_ _I_ _I_ _I_ _I_ _I : I_ _I

I_ _I

#73

Zone 3 Wireless Serial Number

I_ _I_ _I_ _I_ _I_ _I_ _I : I_ _I

I_ _I

#74

Zone 4 Wireless Serial Number

I_ _I_ _I_ _I_ _I_ _I_ _I : I_ _I

I_ _I

			Aux
		Serial Number	1	2
#81	Keyfob 1 Serial Number	I_ _I_ _I_ _I_ _I_ _I_ _I_ _I	I_ _I_ _I
#82	Keyfob 2 Serial Number	I_ _I_ _I_ _I_ _I_ _I_ _I_ _I	I_ _I_ _I
#83	Keyfob 3 Serial Number	I_ _I_ _I_ _I_ _I_ _I_ _I_ _I	I_ _I_ _I
#84	Keyfob 4 Serial Number	I_ _I_ _I_ _I_ _I_ _I_ _I_ _I	I_ _I_ _I

Top 2 buttons = ARM & DISARM, bottom 2 = AUX 1 & 2 can be programmed for several functions
1 = Police Panic
2 = Aux/Medical
3 = Bell ON
4 = PGM Output
5 = Access on PGM
7 = FULLY ARM (Use ON key + Selected AUX key programmed as 7
8 = STAY ARM (Use ON key + Selected AUX key programmed as 8

#90

Download Phone Number

I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
(Press

to Blank Out)

#91	Ring Count
	Default
	09	I_0_I_9_I (00 to 15)
#92	Downloading Features (Toggle Options ON/OFF)
	Default
	ON OFF OFF OFF	I_ON_I I_ON_I I_ON_I I_OFF_I	Ring Method (# of Rings) Answering Machine Over-Ride FUNCTION + 6 Download Enable Reserved
#93	Auto Download ID # (Do not Program)
	I_ _I_ _I
#94	Installer Code (Leave this Default Please)
	Default
	4567	I_4_I_5_I_6_I_7_I
#95	User 1 Master Code
	Default
	1234	I_1_I_2_I_3_I_4_I
#96	Dealer Options 1 (Toggle Options ON/OFF)
	Default
	OFF ON OFF OFF	I_OFF_I I_OFF_I I_OFF_I I_OFF_I	Dealer Code (Panel) Lockout Enable User Code 1 Lockout Reserved Reserved
#97	Dealer Options 2 (Toggle Options ON/OFF)
	Default
	OFF OFF OFF OFF	I_OFF_I I_OFF_I I_OFF_I I_OFF_I	International Dialing Protocol Invert Bell Output System Trouble Auto Reset User 1 Code Program Only
#98	Dial Attempts
	Default
	9	I_9_I	(1 to F)