Moose Z900 Program

Click HERE for Binary Programming
Move to Location 3 digits + # * = Saves Data # Moves to next Location
There are 2 sections of programming, User and Installer sections
INSTALLER Program (Locations 034 to 271)

1. Hold 9 key 3 seconds until keypad beeps
2. Enter Installer Code (9 6 3 2 1) (Keypad should flash)
OR (If Installer Code was changed)
1. Power down then power up
2. Press and hold 3 and 9 keys for 3 seconds (Keypad should flash)
(Must exit Installer Program then enter User Program to add Codes, change Entry/Exit/Siren times)
USER Program (Locations 001 to 033)
1. Hold 9 key 3 seconds until keypad beeps
2. Enter Master Code (Keypad should flash)
Go to Location 1, 2 or 3 digit Location then #
Program Location After each digit entered press * to save then # to move to next location
(To program Account as 1224 press 057 # to go to location then enter 1* # 2* # 2* # 4* #)
Exit Program Press * twice
Default Panel Enter programming then press 2 5 4 + # + 1 + *

USER LEVEL PROGRAMMING
1# Master Code I_1_I_2_I_4_I_5_I 1. Enter location 1 to 6 then #
2. Enter new code without * or #
3. System will give long tone and exit
2# User 2 Code I_ _I_ _I_ _I_ _I
3# User 3 Code I_ _I_ _I_ _I_ _I
4# User 4 Code I_ _I_ _I_ _I_ _I
5# User 5 Code I_ _I_ _I_ _I_ _I
6# User 6 Code I_ _I_ _I_ _I_ _I (Usually Hostage Code)
>
Below locations require entering location then # + Value then #
>
7# Usage Count Code 6 I_255*#_I (1 to 255 uses, 255 = Unlimited)
8# Time Until Next Com Test I_0*#_I (no need to program)
9# Clear Alarm Memory (No value required)
10# Delete User Codes 1 to 6 (Press 2 – 6 + # to delete)
11# Entry Delay 1 Time I_30*#_I (1 to 255 seconds)
12# Entry Delay 2 Time I_45*#_I (1 to 255 seconds)
13# Exit Delay Time I_61*#_I (1 to 255 seconds)
(Even numbers in Exit Delay give exit beeps, odd numbers do not)
>
14# Access Output Time I_5*#_I (1 to 255 seconds, 0 = Switch with Code)
15# Delay Burg Output I_0*#_I (0 to 255 seconds)
16# Burg Cutoff Time I_6*#_I (1 to 255 minutes, 255 = Unlimited)
17# Aux A (Fire) Panic Cutoff Time I_6*#_I (1 to 255 minutes, 255 = Unlimited)
18# Aux B (Police) Panic Cutoff Time I_6*#_I (1 to 255 minutes, 255 = Unlimited)
19# Aux C (Medical) Panic Cutoff Time I_6*#_I (1 to 255 minutes, 255 = Unlimited)
20# Time between Communicator Test I_1*#_I (0 = Test every 12 Hours, 1 = 7 Days)
21# to 32# Exits to Programming Entry Mode
33# Begin Upload Data (Sends to Download Computer)
>
INSTALLER LEVEL PROGRAMMING
>
34# Configuration User Code 1 I_3*#_I (3 = Standard user Code)
35# Configuration User Code 2 I_3*#_I
36# Configuration User Code 3 I_3*#_I
37# Configuration User Code 4 I_3*#_I
38# Configuration User Code 5 I_3*#_I
39# Configuration User Code 6 I_9*#_I (9 = Duress Code)
>
Lights will all begin flashing, press 41 # to continue
>
41# Zone 1 Configuration I_64*#_I 64 = Delay 1
42# Zone 2 Configuration I_72*#_I 65 = Instant
43# Zone 3 Configuration I_81*#_I 66 = Fire
44# Zone 4 Configuration I_65*#_I 03 = Remote Panic
45# Zone 5 Configuration I_65*#_I 72 = Delay #2
46# Zone 6 Configuration I_65*#_I 81 = Interior Motion

>

47# Communicator Delay/Enable I_1*#_I (1 to 255 seconds, 0 = Dialer Disabled)
48# Dial Attempts Phone 1 I_8*#_I (1 to 15 attempts)
49# Dial Attempts Phone 2 I_8*#_I (1 to 15 attempts)
50# Dual Reporting of Alarms I_0*#_I (1 = Yes, 0 = No)
51# Dual Reporting of Non-Alarms I_0*#_I (1 = Yes, 0 = No)
52# Communicator On-Hook Time I_3*#_I (1 to 15 seconds)
53# Time between Dial Attempts I_10*#_I (1 to 255 seconds)
54# Abort Communicator on Disarming I_0*#_I (1 = Yes, 0 = No)
55# Disable Dialer Test on Power-Up I_0*#_I (1 = Yes, 0 = No)
56# Exception Open/Close Restore I_0*#_I (1 = Yes, 0 = No)
>
57# 1st Digit of Account Number I_?*#_I (Program 10 if Account contains a 0)
58# 2nd Digit of Account Number I_?*#_I A = 10, B = 11, C = 12, D = 13, E = 14, F = 15
59# 3rd Digit of Account Number I_?*#_I
60# 4th Digit of Account Number I_?*#_I
>
61# Transmission Format I_2*#_I
0 = Autobaud, Format selected based on receiver handshake
1 = 1400Hz Handshake, 1900Hz Data, 10 Baud
2 = 2300Hz Handshake, 1800Hz Data, 20 Baud
3 = 1400 or 2300Hz Handshake, 1800Hz Data, 40 Baud
4 = 1400Hz Handshake, 1900Hz Data, 15 Baud
5 = Radionics BFSK (1400 or 2300Hz Handshake)
6 = Sescoa Model 3000, Slow Format
7 = Sescoa Model 3000, Fast Format
>
62# Single Round Format I_0*#_I (1 = Yes, 0 = No)
63# 4/2 Format Enable I_1*#_I (1 = Yes, 0 = No)
64# Extended Standard I_0*#_I (1 = Yes, 0 = No)
65# Extended Single Line I_0*#_I (1 = Yes, 0 = No)
66# Parity Checksum I_0*#_I (1 = Yes, 0 = No)
67# Touchtone Dialing I_1*#_I (1 = Yes, 0 = No)
>
68# Zone 1 1st Digit Report Code I_3*#_I (Second digit is at 216, sends 31)
69# Zone 2 1st Digit Report Code I_3*#_I (Second digit is at 217, sends 32)
70# Zone 3 1st Digit Report Code I_3*#_I (Second digit is at 218, sends 33)
71# Zone 4 1st Digit Report Code I_3*#_I (Second digit is at 219, sends 34)
72# Zone 5 1st Digit Report Code I_3*#_I (Second digit is at 220, sends 35)
73# Zone 6 1st Digit Report Code I_3*#_I (Second digit is at 221, sends 36)
>
74# KP Fire 1st Digit Report Code I_2*#_I (Second digit is at 244, sends 23)
75# KP Police 1st Digit Report Code I_2*#_I (Second digit is at 245, sends 21)
76# KP Medical 1st Digit Report Code I_2*#_I (Second digit is at 246, sends 26)
>
77# Duress 1st Digit Report Code I_2*#_I (Second digit is in 214, sends 22)
78# Open 1st Digit Report Code I_0*#_I (Second digit is at 209)
79# Close 1st Digit Report Code I_0*#_I (Second digit is at 209)
80# Bypass 1st Digit Report Code I_0*#_I (Second digit is at 228 to 233)
81# Cancel 1st Digit Report Code I_0*#_I (Do not program, it doesn’t work like you think)
82# Zone Restore 1st Digit Report Code I_0*#_I (Second digit is at 222)
83# Supervisory 1st Digit Report Code I_7*#_I (Second digit is at 234 to 239)
84# Low Bat 1st Digit Report Code I_0*#_I (Second digit is at 241)
85# Bat Restore 1st Digit Report Code I_0*#_I (second digit is at 241)
86# AC Fail 1st Digit Report Code I_7*#_I (second digit is at 240)
87# AC Restore 1st Digit Report Code I_0*#_I (second digit is at 240, if needed use E)
88# Memory Error Report Code I_0*#_I (second digit is at 242)
89# Auto Test Report Code I_0*#_I (second digit is at 243)
>
90# to 105# Telephone 1 (16 digits) (Program each Digit + * + # + next digit etc)

I _1*#_ I _8*#_ I _?*#_ I _?*#_ I _?*#_ I _?*#_ I _?*#_ I _?*#_ I _?*#_ I _?*#_ I _?*#_ I _?*#_ I _?*#_ I _?*#_ I _?*#_ I _?*#_ I
90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105

11 = *
12 = #
13 = 3 Second Pause
14 = Wait for Dial Tone
15 = End Phone Number
>

106# Audio Listen-In Phone 1 I_0*#_I (1 = Yes, 0 = No)
108# Copy Telephone 1 Account to Telephone 2 (This is a quick way to over-write 2nd phone info)
109# Copy Telephone 1 Phone to Telephone 2 (This is a quick way to over-write 2nd phone info)
110# to 159# Second Phone Number & Reporting (Not Used)
160# Number of Rings before Answer I_10*#_I (1 to 15 Rings, 0 Disables)
161# to 176# Download Number (Leave Blank)

I _ _ I _ _ I _ _ I _ _ I _ _ I _ _ I _ _ I _ _ I _ _ I _ _ I _ _ I _ _ I _ _ I _ _ I _ _ I _ _ I
161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176

177# Two Digit Arming I_0*#_I (1 = Yes, 0 = No)
178# Enable Force Arming I_0*#_I (1 = Yes, 0 = No)
179# Permanent Force Arming I_0*#_I (1 = Yes, 0 = No)
180# Delay Burg Restorals Until Cutoff I_0*#_I (1 = Yes, 0 = No)
181# Alarm Reports Until Lockout I_3*#_I (1 to 15 Alarms before Lockout)
182# Pulsing Burg Siren Output I_0*#_I (1 = Yes, 0 = No)
183# Pulsing Fire Output I_0*#_I (1 = Yes, 0 = No)
184# Burg Loop Audible Lockout I_0*#_I (1 = Yes, 0 = No)
185# Keyswitch Mode Change I_0*#_I (1 = Yes, 0 = No)
186# Supervisory/Day Alert Latch I_0*#_I (1 = Yes, 0 = No)
187# Automatic Interior Off I_0*#_I (1 = Motion in Home/Away Mode, 0 = No)
188# Extend BA Loop Stabilization I_0*#_I (1 = Yes, 0 = No)
189# Disable Interior Follower I_0*#_I (1 = Yes, 0 = No)
190# Interior On/Off if Armed I_0*#_I (1 = Bypass (4) key active if armed, 0 = No)
191# Delay Off When Interior Off I_0*#_I (1 = Yes, 0 = No)
192# Siren Test on Arming I_0*#_I (1 = Yes, 0 = No)
193# Reset Test Timer on Kissoff I_0*#_I (1 = Yes, 0 = No)
194# Interior Default Upon Disarm I_0*#_I (1 = Yes, 0 = No)
>
195# Disable Keypad Bypassing I_0*#_I (1 = Yes, 0 = No)
196# Disable Key 4 Interior Bypass I_0*#_I (1 = Yes, 0 = No)
197# Disable Key 6 Chime I_0*#_I (1 = Yes, 0 = No)
198# Disable Key 7 Reset I_0*#_I (1 = Yes, 0 = No)
199# Disable Key 8 Walk Test I_0*#_I (1 = Yes, 0 = No)
200# Silent Keypad on Burg I_0*#_I (1 = Yes, 0 = No)
201# Silent Keypad for Police Panic I_0*#_I (1 = Yes, 0 = No)
202# Start Entry Delay on KP Entries I_0*#_I (1 = Yes, 0 = No)
>
203# Zone 1 Trouble on Open or Short I_0*#_I (1 = Yes, 0 = No)
204# Zone 2 Trouble on Open or Short I_0*#_I (1 = Yes, 0 = No)
205# Zone 3 Trouble on Open or Short I_0*#_I (1 = Yes, 0 = No)
206# Zone 4 Trouble on Open or Short I_0*#_I (1 = Yes, 0 = No)
207# Zone 5 Trouble on Open or Short I_0*#_I (1 = Yes, 0 = No)
208# Zone 6 Trouble on Open or Short I_0*#_I (1 = Yes, 0 = No)
>
209# Extended Reporting User 1 I_0*#_I
210# Extended Reporting User 2 I_0*#_I
211# Extended Reporting User 3 I_0*#_I
212# Extended Reporting User 4 I_0*#_I
213# Extended Reporting User 5 I_0*#_I
214# Extended Reporting User 6 I_2*#_I (2nd Digit of Hostage Code)
215# Extended Keyswitch Report Code I_0*#_I
>
216# Zone 1 2nd Digit Alarm Report Code I_1*#_I (first digit is at 068, sends 31)
217# Zone 2 2nd Digit Alarm Report Code I_2*#_I (first digit is at 069, sends 32)
218# Zone 3 2nd Digit Alarm Report Code I_3*#_I (first digit is at 070, sends 33)
219# Zone 4 2nd Digit Alarm Report Code I_4*#_I (first digit is at 071, sends 34)
220# Zone 5 2nd Digit Alarm Report Code I_5*#_I (first digit is at 072, sends 35)
221# Zone 6 2nd Digit Alarm Report Code I_6*#_I (first digit is at 073, sends 36)
>
222# Zone 1 2nd Digit Restore Report I_0*#_I (first digit is at 082)
223# Zone 2 2nd Digit Restore Report I_0*#_I
224# Zone 3 2nd Digit Restore Report I_0*#_I
225# Zone 4 2nd Digit Restore Report I_0*#_I
226# Zone 5 2nd Digit Restore Report I_0*#_I
227# Zone 6 2nd Digit Restore Report I_0*#_I
>
228# Zone 1 2nd Digit Bypass Report I_0*#_I (Program these as 0)
229# Zone 2 2nd Digit Bypass Report I_0*#_I
230# Zone 3 2nd Digit Bypass Report I_0*#_I
231# Zone 4 2nd Digit Bypass Report I_0*#_I
232# Zone 5 2nd Digit Bypass Report I_0*#_I
233# Zone 6 2nd Digit Bypass Report I_0*#_I
>
234# Zone 1 Supervisory Report Code I_0*#_I (first digit is at 083)
235# Zone 2 Supervisory Report Code I_0*#_I
236# Zone 3 Supervisory Report Code I_0*#_I
237# Zone 4 Supervisory Report Code I_0*#_I
238# Zone 5 Supervisory Report Code I_0*#_I
239# Zone 6 Supervisory Report Code I_0*#_I (Use 6 if Smoke Detector on Zone 6)
>
240# Extended AC Report Code I_9*#_I (first digit is at 086, sends 79)
241# Extended Battery Report Code I_0*#_I (first digit is at 084)
242# Extended Memory Error Report Code I_0*#_I (first digit is at 088)
243# Entended Test Code I_0*#_I (first digit is at 089)
>
244# Extended KP Fire Panic Code I_3*#_I (first digit is at 074, sends 23)
(If Z700 this is 2nd digit of whatever panic you program it as (see section 261))
245# Extended KP Police Panic Code I_1*#_I (first digit is at 075, sends 21)
246# Extended KP Medical Panic Code I_6*#_I (first digit is at 076, sends 26)
247# Extended Missing KP Report Code I_0*#_I
>
248# Eliminate Burg EOL Resistors I_0*#_I (1 = No EOL Resistors, 0 = EOL Resistors)
>
249# Exits to Programming Entry Mode
250# Default Master Code (No Value Required, Keypad beeps)
>
251# Fast Loop Response Time I_2*#_I (80ms)
252# Slow Loop Response Time I_6*#_I (320ms)
0 = 40 ms 1 = 40 ms 2 = 80 ms 3 = 120 ms 4 = 160 ms 5 = 200 ms
6 = 320 ms 7 = 480 ms 8 = 600ms 9 = 800 ms 10 = 1 sec 11 = 2 sec
12 = 4 sec 13 = 6 sec 14 = 8 sec 15 = 10 sec

253# Exits to Programming Entry Mode
254# Default Panel to Factory I_0*#_I (0 = Normal, 1 = Defaults)
(Enter 1 + * + * will default and exit programming)
>
255# Installer Code I_9_I_6_I_3_I_2_I_1_I
(Enter as 96321, not as 9*#, 8*# etc)
>
256# Assignable Output Definition I_1_I (+12 Volt Output Terminal 3)
0 = Alarm Condition by Panic Keys
1 = Switched Power Reset using 7 Key (Smoke Reset)
2 = Activation of Access Output
3 = Supervisory/Trouble Conditions
4 = Entrance Pre-Alarms and Chime
>
257# Burg Activates Assignable Output I_1*#_I (1 = + 12 Volts Activation, 0 = No)
258# Aux A (Fire) Activates Output I_1*#_I (1 = + 12 Volts Activation, 0 = No)
259# Aux B (Police) Activates Output I_1*#_I (1 = + 12 Volts Activation, 0 = No)
260# Aux C (Medical) Activates Output I_1*#_I (1 = + 12 Volts Activation, 0 = No)
>
261# Disable Keypad Fire Panic I_0*#_I (1 = Yes, 0 = No)
(If Z700 program 0 here to disable Panic or 1 = Burg Alarm, 2 = Fire, 3 = Police, 4 = Medical)

262# Disable Keypad Police Panic I_0*#_I (1 = Yes, 0 = No)
263# Disable Keypad Medical Panic I_0*#_I (1 = Yes, 0 = No)
>
264# Reseved for Future Use (Do not Program)
265# Tone Test Generation (Factory Use Only)
266# Factory ID (Factory Use Only)
>
267# Telephone 1 Download Complete I_0*#_I (Report Disabled)
268# Telephone 2 Download Complete I_0*#_I (Report Disabled)
269# Extended Download Complete I_0*#_I (Report Disabled)
270# Pulse Dialing 66/33 Make/Break Ratio I_0*#_I (Leave Alone)
271# KP Panic 3 sec Hold or Press Twice I_1*#_I (0 = Press Twice, 1 = 3 Second Hold)