Moose Z1100 System II Program

Click HERE for Binary Programming
Move to
Location
3 digits + # * = Save Data # Moves to next Location
Enter Program 1. Press Program button then 9 + 98765 (All LED’s will flash)

OR (If Installer Code was changed)

1. Hold Program Button while powering up (All LED’s will flash)

Move to
Location
Enter 3-Digit location + #
Entering Data Enter 1 to 3 Digits in location + * to save + # to move to next location
Exit Program Press * twice
Default Panel 1. Hold Program Button while powering up (All LED’s will flash)
2. Press 156 + #
3. Press 1 + ** System exits programming
4. Power down and wait 5 seconds then power up again

001# User Code 1 I_2_I_4_I_5_I_ _I_ _I 1. Enter location 001 to 008 then #
(Default is 245)
002# User Code 2 I_ _I_ _I_ _I_ _I_ _I 2. Enter 1 to 5 digit code without * or #
003# User Code 3 I_ _I_ _I_ _I_ _I_ _I 3. System will give long tone and exit
004# User Code 4 I_ _I_ _I_ _I_ _I_ _I (Up to 5 Digits)
005# User Code 5 I_ _I_ _I_ _I_ _I_ _I (Up to 5 Digits)
006# User Code 6 I_ _I_ _I_ _I_ _I_ _I (Up to 5 Digits)
007# User Code 7 I_ _I_ _I_ _I_ _I_ _I (Up to 5 Digits)
008# User Code 8 I_ _I_ _I_ _I_ _I_ _I (Up to 5 Digits)
009# Temporary User Code 9 I_ _I_ _I_ _I_ _I_ _I (Up to 5 Digits)
010# User Program Code I_9_I_8_I_7_I_6_I_5_I (Up to 5 Digits)
011# Temporary User Code Count I_255*#_I (000 to 255, 255 = Unlimited)
012# Time Till Next Comm/Battery Test I_024*#_I (24 Hours)
013# Clear Alarm Memory (No Value Required)
014# Delete User Codes 1 to 9 (Example: 14 # + 5 will delete User Code 5)
015# Upload Data/Start Downloading (No Value Required)
016# Installer Program Code I_9_I_8_I_7_I_6_I_5_I (Enter 98765, not 9*#, 8*# etc)
017# Exit Delay I_060*#_I Even Numbers = Audible Exit Beeps
018# Entry Delay 1 I_030*#_I 001 to 255 seconds
019# Entry Delay 2 I_045*#_I 001 to 255 seconds
020# Access On Time I_005*#_I 001 to 255 Seconds, 000 = Toggle
021# Delay Burglar Alarm I_000*#_I 000 to 255 Seconds
022# Burglar Output Time in Minutes I_006*#_I 6 Minutes
023# Fire Output I_006*#_I 6 Minutes
024# Police Output I_006*#_I 6 Minutes
025# Medical Output I_006*#_I 6 Minutes
031# Automatic Interior Off I_000*#_I 000 = No, 001 = Motions Home/Away
038# Zone 1 Definition I_064*#_I (Below are typical Zone Types)
039# Zone 2 Definition I_072*#_I 064 = Delay
040# Zone 3 Definition I_081*#_I 065 = Instant
041# Zone 4 Definition I_065*#_I 066 = Fire
042# Zone 5 Definition I_065*#_I 072 = Delay 2
043# Zone 6 Definition I_065*#_I 081 = Interior Follower
044# Zone 7 Definition I_065*#_I 003 = Panic buttons
045# Zone 8 Definition I_065*#_I 002 = Medical Panic
046# Zone 1 Supervisory I_000*#_I 000 = Open, 001 = Short
047# Zone 2 Supervisory I_000*#_I 000 = Open, 001 = Short
048# Zone 3 Supervisory I_000*#_I 000 = Open, 001 = Short
049# Zone 4 Supervisory I_000*#_I 000 = Open, 001 = Short
050# Zone 5 Supervisory I_000*#_I 000 = Open, 001 = Short
051# Zone 6 Supervisory I_000*#_I 000 = Open, 001 = Short
052# Zone 7 Supervisory I_000*#_I 000 = Open, 001 = Short
053# Zone 8 Supervisory I_000*#_I (If Fire on Zone 8 program as 001)
054# User Code 1 Configuration I_003*#_I
055# User Code 2 Configuration I_003*#_I 003 = Normal User Code
056# User Code 3 Configuration I_003*#_I
057# User Code 4 Configuration I_003*#_I
058# User Code 5 Configuration I_003*#_I
059# User Code 6 Configuration I_003*#_I
060# User Code 7 Configuration I_003*#_I
061# User Code 8 Configuration I_003*#_I
062# User Code 9 Configuration I_009*#_I 009 = Hostage Code
063# Two Digit Arming I_000*#_I 000 = No, 001 = Yes
064# Command Keys 4 & 5 While Armed I_000*#_I 000 = No, 001 = Yes
066# Disable Keypad Fire I_000*#_I 000 = No, 001 = Yes
067# Disable Keypad Police I_000*#_I 000 = No, 001 = Yes
068# Disable Keypad Medical I_000*#_I 000 = No, 001 = Yes
069# Disable Keypad Shunting I_000*#_I 000 = No, 001 = Yes
070# Silent Keypad on Burglar Activation I_000*#_I 000 = No, 001 = Yes
071# Silent Keypad on Police Activation I_000*#_I 000 = No, 001 = Yes
072# Start Entry Delay 1 from Keypad I_000*#_I 000 = No, 001 = Yes
073# Disable Keypad Command 4 I_000*#_I 000 = No, 001 = Yes
074# Disable Keypad Command 5 I_000*#_I 000 = No, 001 = Yes
075# Disable Keypad Command 6 I_000*#_I 000 = No, 001 = Yes
076# Disable Keypad Command 7 I_000*#_I 000 = No, 001 = Yes
077# Disable Keypad Command 8 I_000*#_I 000 = No, 001 = Yes
078# Communicator Disable/Delay I_000*#_I 000 = Disable 001 to 255 Seconds Delay
079# Dial Attempts I_008*#_I (001 to 255 Attempts)
080# Communicator Alarm Abort I_000*#_I (000 = No, 001 = Yes)
081# Disable Dialer Test on Power Up I_000*#_I (000 = No, 001 = Yes)
082# Exception Opening/System Restore I_000*#_I (000 = No, 001 = Yes)
083# 1st Digit of Account Number I_00?*#_I (001 to 015) Account 1234 would
084# 2nd Digit of Account Number I_00?*#_I (000 to 015) be entered as
085# 3rd Digit of Account Number I_00?*#_I (000 to 015) 001# 002# 003# 004#
086# 4th Digit of Account Number I_00?*#_I (000 to 015) (if 0 in Account use 010)
087# Communicator Format I_002*#_I
000 = Autobaud (Auto selects handshake from Receiver)
001 = 1400 Hz Handshake, 1900 Hz Data 10 Baud (Osborne, Radionics, Silent Knight)
002 = 2300 Hz Handshake, 1800 Hz Data 20 Baud (DCI, FBII, Franklin, Sescoa)
003 = 1400 or 2300 Hz Handshake, 1800 Hz Data 40 Baud (Radionics Superfast)
004 = 1400 Hz Handshake, 1900 Hz Data, 15 Baud (Silent Knight Fast Format)
005 = 1400 Hz or 2300 Hz Handshake (Radionics BFSK)
088# Single Round Report I_000*#_I (000 = No, 001 = Yes)
089# 4/2 Format I_001*#_I (000 = No, 001 = Yes)
090# Standard/Extended I_000*#_I (000 = No, 001 = Yes)
091# Single Line Extended (Radionics) I_000*#_I (000 = No, 001 = Yes)
092# Parity Checksum (Radionics) I_000*#_I (000 = No, 001 = Yes)
093# Touchtone Dialing I_001*#_I (000 = No, 001 = Yes)
094# Zone 1 Report Code (Sends 31) I_003*#_I (000 = Disabled, 001 to 015)
095# Zone 2 Report Code (Sends 32) I_003*#_I (000 = Disabled, 001 to 015)
096# Zone 3 Report Code (Sends 33) I_003*#_I (000 = Disabled, 001 to 015)
097# Zone 4 Report Code (Sends 34) I_003*#_I (000 = Disabled, 001 to 015)
098# Zone 5 Report Code (Sends 35) I_003*#_I (000 = Disabled, 001 to 015)
099# Zone 6 Report Code (Sends 36) I_003*#_I (000 = Disabled, 001 to 015)
100# Zone 7 Report Code (Sends 37) I_003*#_I (000 = Disabled, 001 to 015)
101# Zone 8 Report Code (Sends 38) I_003*#_I (000 = Disabled, 001 to 015)
102# Fire Panic Report Code I_001*#_I (Sends 19, 2nd digit in 165)
103# Police Panic Report Code I_002*#_I (Sends 29, 2nd digit in 165)
104# Medical Panic Report Code I_004*#_I (Sends 49, 2nd digit in 165)
105# Duress Report Code I_002*#_I (Sends 29, 2nd digit is user number)
106# Open Report Code I_000*#_I (000 = Disabled, 001 to 015)
107# Close Report Code I_000*#_I (000 = Disabled, 001 to 015)
108# Bypass Report Code I_000*#_I (000 = Disabled, 001 to 015)
109# Cancel Report Code I_000*#_I (000 = Disabled, 001 to 015)
110# Restore Report Code I_000*#_I (000 = Disabled, 001 to 015)
111# Supervisory Report Code I_000*#_I (000 = Disabled, 001 to 015)
112# Low Battery/Fuse Report Code I_007*#_I (2nd Digit in 162, sends 78)
113# Low Battery/Fuse Restore Code I_000*#_I (2nd Digit in 162, Disabled)
114# AC Fail Report Code I_007*#_I (2nd Digit in 161, sends 79)
115# AC Fail Restore I_000*#_I (2nd Digit in 161, Disabled)
116# Memory Error Report Code I_000*#_I (2nd Digit in 163, Disabled)
117# Test Report Code I_000*#_I (2nd Digit in 164, Disabled)
118# to 153# is Telephone 2 Options Do not Program
154# Copy Telephone 1 Programming to 2 (No Value Required)
155# Copy Telephone 1 to Telephone 2 (No Value Required)
(Enter 154# then 155# as quick and dirty way to overwrite old Phone 2 Programming)
156# Default Panel I_000#_I (000 = No, 001 = Yes)
157# Listen In Telephone 1 I_000#_I (000 = No, 001 = Yes)
158# Listen In Telephone 2 I_000#_I (000 = No, 001 = Yes)
159# Line Seizure Hangup Time I_003#_I (000 to 255 Seconds)
160# Time Between Dial Attempts I_010#_I (000 to 255 Seconds)
161# Extended AC Report Code I_009#_I (1st Digit in 114, sends 79)
162# Extended Batt/Fuse Report Code I_008#_I (1st Digit in 112, sends 78)
163# Extended Memory Error I_000#_I (1st Digit in 116, Disabled)
164# Extended Test Code I_000#_I (1st Digit in 117, Disabled)
165# Extended Keypad Panic I_009#_I (1st Digit in 102 to 104)
166# Parity Checksum Formats 0, 1, 2) I_000#_I (000 = No, 001 = Yes)
167# Factory TouchTone Test Tones 0 to 9 000 (000 = No, 001 = Yes)
168# Telephone 1 Digit 1 I_001*#_I 011 = *
169# Telephone 1 Digit 2 I_008*#_I 012 = #
170# Telephone 1 Digit 3 I_000*#_I 013 = 3 Second Pause
171# Telephone 1 Digit 4 I_000*#_I 014 = Wait for Dial Tone
172# Telephone 1 Digit 5 I_00?*#_I 015 = Ends Number
173# Telephone 1 Digit 6 I_00?*#_I
174# Telephone 1 Digit 7 I_00?*#_I Use 000 for 0 in Phone Number
175# Telephone 1 Digit 8 I_00?*#_I
176# Telephone 1 Digit 9 I_00?*#_I
177# Telephone 1 Digit 10 I_00?*#_I
178# Telephone 1 Digit 11 I_00?*#_I
179# Telephone 1 Digit 12 I_015*#_I
180# Telephone 1 Digit 13 I_015*#_I
181# Telephone 1 Digit 14 I_015*#_I
182# Telephone 1 Digit 15 I_015*#_I
183# Telephone 1 Digit 16 I_015*#_I
184# Telephone 1 Digit 17 I_015*#_I
185# Telephone 1 Digit 18 I_015*#_I
186# Telephone 1 Digit 19 I_015*#_I
187# Telephone 1 Digit 20 I_015*#_I
188# Telephone 1 Digit 21 I_015*#_I
189# Telephone 1 Digit 22 I_015*#_I
190# Telephone 1 Digit 23 I_015*#_I
191# Telephone 1 Digit 24 I_015*#_I
192# Telephone 1 Digit 25 I_015*#_I
193# Telephone 1 Digit 26 I_015*#_I
194# Return to Run Mode (No Value Required)
195# Telephone 2 Digit 1 I_015*#_I 011 = *
196# Telephone 2 Digit 2 I_015*#_I 012 = #
197# Telephone 2 Digit 3 I_015*#_I 013 = 3 Second Pause
198# Telephone 2 Digit 4 I_015*#_I 014 = Wait for Dial Tone
199# Telephone 2 Digit 5 I_015*#_I 015 = Ends Number
200# Telephone 2 Digit 6 I_015*#_I
201# Telephone 2 Digit 7 I_015*#_I Use 000 for 0 in Phone Number
202# Telephone 2 Digit 8 I_015*#_I
203# Telephone 2 Digit 9 I_015*#_I
204# Telephone 2 Digit 10 I_015*#_I
205# Telephone 2 Digit 11 I_015*#_I
206# Telephone 2 Digit 12 I_015*#_I
207# Telephone 2 Digit 13 I_015*#_I
208# Telephone 2 Digit 14 I_015*#_I
209# Telephone 2 Digit 15 I_015*#_I
210# Telephone 2 Digit 16 I_015*#_I
211# Telephone 2 Digit 17 I_015*#_I
212# Telephone 2 Digit 18 I_015*#_I
213# Telephone 2 Digit 19 I_015*#_I
214# Telephone 2 Digit 20 I_015*#_I
215# Telephone 2 Digit 21 I_015*#_I
216# Telephone 2 Digit 22 I_015*#_I
217# Telephone 2 Digit 23 I_015*#_I
218# Telephone 2 Digit 24 I_015*#_I
219# Telephone 2 Digit 25 I_015*#_I
220# Telephone 2 Digit 26 I_015*#_I
Press * to exit