1. Home
  2. Linear
  3. Linear DVS
  4. Linear DVS
 

Linear DVS 2408 Program

Programming Keys
Formats Contact ID or 4/2 (Contact ID preferred)
Enter Program 1. Enter Master Code + TEST (1 Gong + 5 Beeps)
2. Enter Master Code Again + TEST (1 Gong + 5 Beeps, all active zones light)
Exit Program Press OFF for 3 seconds
Program Location Location + HOME + Enter new Value + AWAY (should hear 1 bing)
(To program 30 second Entry Delay press 25 + HOME + 30 + AWAY)
Delete Location Location + HOME + AWAY (should hear 1 bing)
Compatible
Wireless 		DXS-10 Wireless Keypad DXS-81 Bill Trap
DXS-31 Door/Window DXS-91 Glass Break
DXS-54 Motion Detector DXT-21 & DXT-23 Remotes
DXS-71 Smoke Detector DXT-41 & DXT-42 2 Keyfobs
DXS-72 Smoke Detector DXT-61 Remote Panic
Hardwire Zones (Hardware Zones can be any Zone Number)
301 + HOME + Zone (01 to 24) + AWAY (This Assigns Hardwire Loop 1 as Zone)
to
308 + HOME + Zone (01 to 24) + AWAY (This Assigns Hardwire Loop 8 as Zone)
(Once Hardwired Zone is enabled you don’t learn it in, just set Zone type)
Add Sensor Enter sensor number (01 to 24), zone light will flash, activate sensor
1 “Bing” = Program OK, 2 “Bings” = sensor already programmed in location
(If learning DX-10 keypad press and hold * and do not program a zone type)
Delete Sensor 1. Enter sensor to remove (01 to 24), zone light will flash
2. Press TEST, 1 “Bing” will sound and zone light will turn off
Set Zone Type 1. Enter Sensor Number (01 to 24) DVS1200 (01 to 12)
2. Press HOME + Sensor type (1 to 10) + AWAY (keypad sounds 1 “Bing”)
(do not program ANY zone type for DXS-10 keypad)
Supervisory Zone Number + HOME + (16 or 17) + AWAY

Non-Supervised 16 (Panic Buttons/Remote Keypads)
Supervised 17 (Doors, Smokes, Motions etc)

By default any wireless sensor added to system is supervised

Defaulting Panel While in programming press 999 + TEST + 999 + TEST wait 10 seconds
Note: After defaulting press * + New 4 to 5 Digit Master Code + OFF
Loc Description Possible Entries
01 Zone 01 Type I_ _I 1 = Home Automation
2 = Emergency
3 = Silent Panic
4 = Fire
5 = Perimeter
6 = Entry/Exit
7 = Interior Motion
8 = Chime (No Alarm)
9 = 2- Button Arm/Disarm
(Home Automation)
10 = 2-Button Arm/Disarm
(Use for Keyfob)
11 = Environmental
(Siren only, no Report)
02 Zone 02 Type I_ _I
03 Zone 03 Type I_ _I
04 Zone 04 Type I_ _I
05 Zone 05 Type I_ _I
06 Zone 06 Type I_ _I
07 Zone 07 Type I_ _I
08 Zone 08 Type I_ _I
09 Zone 09 Type I_ _I
10 Zone 10 Type I_ _I
11 Zone 11 Type I_ _I
12 Zone 12 Type I_ _I
13 Zone 13 Type I_ _I
14 Zone 14 Type I_ _I
15 Zone 15 Type I_ _I
16 Zone 16 Type I_ _I
17 Zone 17 Type I_ _I
18 Zone 18 Type I_ _I
19 Zone 19 Type I_ _I
20 Zone 20 Type I_ _I
21 Zone 21 Type I_ _I
22 Zone 22 Type I_ _I
23 Zone 23 Type I_ _I
24 Zone 24 Type I_ _I
25 Entry Delay I_30_I 1 to 255 seconds
26 Exit Delay I_60_I 1 to 255 seconds
30 Burg Siren Time I_5_I 1 to 30 minutes
31 Emergency Siren Time I_5_I 1 to 30 minutes
32 Fire Siren Time I_5_I 1 to 30 minutes
40 Automation Output Time I_5_I 0 to 2500 Seconds
0 = Toggle On/Off
50 Keyfob Arming Mode I_3_I 2 = Home Mode
3 = Away Mode
51 Keyfob Disarming Mode I_0_I 0 = OFF Mode
1=Chime Mode
61 Entry Delay Beeps I_1_I 0 = OFF
1 = ON
62 Exit Delay Beeps I_1_I 0 = OFF
1 = ON
63 Burglary Alarm I_0_I 0 = Audible
1 = Silent
64 Emergency Alarm I_0_I 0 = Audible
1 = Silent
65 Quick Arming I_0_I 0 = OFF
1 = ON
66 Auto Restore I_0_I 0 = OFF
1 = ON
67 Auto Bypass of Open Zones I_0_I 0 = OFF
1 = ON
68 Automation Mode During Alarm
(Enabled by Function 72) 		I_0_I 0 = Flash
1 = Steady
69 Automation Bing Tone I_1_I 0 = NO
1 = Yes
70 Remote Arm/Disarm Chirp I_1_I 0 = No Chirps
1 = Chirps
71 Automation Flashes after Alarm I_0_I 0 = Standard
1 = Flashing after Alarm
72 Automation Active during Alarm I_0_I 0 = Standard
1 = Automation Active
73 Automation On while Armed I_0_I 0 = Standard
1 = On while Armed
74 Automation On during Entry/Exit I_0_I 0 = Standard
1 = ON during Entry/Exit
75 Automation Polarity I_1_I 0 = + when OFF
1 = + when ON
76 2-Way Audio
(must have VB2 – VB3 Installed) 		I_2_I 0 = None
1 = Listen
2 = 2-Way Manual
3 = 2-way Full Duplex
78 Voice Enabled
(must have VB2 – VB3 Installed) 		I_2_I 0 = Voice Response Disabled
1 = Voice Response Enabled
86 Call Routing I_1_I 0 = All to Primary or Secondary
1 = Alarms to Primary or Secondary
others to Supervisory Number
87 Remote Access Password I_9_I_8_I_7_I_6_I_5_I_4_I
88 Account Number (0 to 9 only) I_ _I_ _I_ _I_ _I
89 Primary Phone Number Up to 20 digits (A Key = 1 sec pause)
I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
90 Secondary Phone Number Up to 20 digits
I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
91 Supervisory Phone Number Up to 20 digits
I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
92 Duress Code I_ _I 1 to 5 digits
93 Secondary User Code 1 I_ _I 1 to 5 digits
94 Secondary User Code 2 I_ _I 1 to 5 digits
95 Secondary User Code 3 I_ _I 1 to 5 digits
96 Secondary User Code 4 I_ _I 1 to 5 digits
97 Secondary User Code 5 I_ _I 1 to 5 digits
98 Secondary User Code 6 I_ _I 1 to 5 digits
99 Installer Code I_ _I 1 to 5 digits
100 Remote Programming Lockout
(Downloading Enable) 		I_0_I 0 = Unlock (Enabled)
1 = Lock (Disabled)
101 Swinger Shutdown I_0_I 0 = OFF
1 = 5 Alarms until Swinger
103 Dialing Delay I_0_I 0 = No Delay
1 = 15 Second Delay
104 Dialing Method I_0_I 0 = Tone
1 = Pulse
105 Report Format I_1_I 0 = 4/2
1 = Ademco Contact ID
107 Communicator Enabled I_1_I 0 = Disabled
1 = Enabled
108 Report System Trouble I_1_I 0 = NO
1 = Yes
110 Report Force Arming I_0_I 0 = NO
1 = Yes
113 Point ID Reporting for 4/2 Format I_1_I 0 = NO
1 = Yes
Below are 4/2 format signals, normally leave alone, enter 00 to disable
201 General Fire Panic Report Code I_1_I 0 to 99
202 General Emergency Report Code I_2_I 0 to 99
203 General Silent Panic Report Code I_3_I 0 to 99
204 General Burglary Report Code I_4_I 0 to 99
205 General Trouble Report Code I_6_I 0 to 99
210 Sensor 1 Alarm Report Code I_11_I 0 to 99
211 Sensor 2 Alarm Report Code I_12_I 0 to 99
212 Sensor 3 Alarm Report Code I_13_I 0 to 99
213 Sensor 4 Alarm Report Code I_14_I 0 to 99
214 Sensor 5 Alarm Report Code I_15_I 0 to 99
215 Sensor 6 Alarm Report Code I_16_I 0 to 99
216 Sensor 7 Alarm Report Code I_17_I 0 to 99
217 Sensor 8 Alarm Report Code I_18_I 0 to 99
218 Sensor 9 Alarm Report Code I_19_I 0 to 99
219 Sensor 10 Alarm Report Code I_20_I 0 to 99
220 Sensor 11 Alarm Report Code I_21_I 0 to 99
221 Sensor 12 Alarm Report Code I_22_I 0 to 99
222 Sensor 13 Alarm Report Code I_23_I 0 to 99
223 Sensor 14 Alarm Report Code I_24_I 0 to 99
224 Sensor 15 Alarm Report Code I_25_I 0 to 99
225 Sensor 16 Alarm Report Code I_26_I 0 to 99
226 Sensor 17 Alarm Report Code I_27_I 0 to 99
227 Sensor 18 Alarm Report Code I_28_I 0 to 99
228 Sensor 19 Alarm Report Code I_29_I 0 to 99
229 Sensor 20 Alarm Report Code I_30_I 0 to 99
230 Sensor 21 Alarm Report Code I_31_I 0 to 99
231 Sensor 22 Alarm Report Code I_32_I 0 to 99
232 Sensor 23 Alarm Report Code I_33_I 0 to 99
233 Sensor 24 Alarm Report Code I_34_I 0 to 99
234 Sensor 1 Trouble Report Code I_41_I 0 to 99
235 Sensor 2 Trouble Report Code I_42_I 0 to 99
236 Sensor 3 Trouble Report Code I_43_I 0 to 99
237 Sensor 4 Trouble Report Code I_44_I 0 to 99
238 Sensor 5 Trouble Report Code I_45_I 0 to 99
239 Sensor 6 Trouble Report Code I_45_I 0 to 99
240 Sensor 7 Trouble Report Code I_47_I 0 to 99
241 Sensor 8 Trouble Report Code I_48_I 0 to 99
242 Sensor 9 Trouble Report Code I_49_I 0 to 99
243 Sensor 10 Trouble Report Code I_50_I 0 to 99
244 Sensor 11 Trouble Report Code I_51_I 0 to 99
245 Sensor 12 Trouble Report Code I_52_I 0 to 99
246 Sensor 13 Trouble Report Code I_53_I 0 to 99
247 Sensor 14 Trouble Report Code I_54_I 0 to 99
248 Sensor 15 Trouble Report Code I_55_I 0 to 99
249 Sensor 16 Trouble Report Code I_56_I 0 to 99
250 Sensor 17 Trouble Report Code I_57_I 0 to 99
251 Sensor 18 Trouble Report Code I_58_I 0 to 99
252 Sensor 19 Trouble Report Code I_59_I 0 to 99
253 Sensor 20 Trouble Report Code I_60_I 0 to 99
254 Sensor 21 Trouble Report Code I_61_I 0 to 99
255 Sensor 22 Trouble Report Code I_62_I 0 to 99
256 Sensor 23 Trouble Report Code I_63_I 0 to 99
257 Sensor 24 Trouble Report Code I_64_I 0 to 99
258 Force Arming Report Code I_65_I 0 to 99
259 Duress Report code I_66_I 0 to 99
261 KP Fire Report Code I_68_I 0 to 99
262 KP Emergency (Police) Report Code I_69_I 0 to 99
263 System Test/Cancel Report Code I_70_I 0 to 99
264 System Low Bat Restore Code I_71_I 0 to 99
266 System Low Bat Report Code I_73_I 0 to 99
Hardwired loops must be assigned a Zone from 01 to 24
301 Hardwire Zone 1 Assignment I_ _I 01 to 24
302 Hardwire Zone 2 Assignment I_ _I 01 to 24
303 Hardwire Zone 3 Assignment I_ _I 01 to 24
304 Hardwire Zone 4 Assignment I_ _I 01 to 24
305 Hardwire Zone 5 Assignment I_ _I 01 to 24
306 Hardwire Zone 6 Assignment I_ _I 01 to 24
307 Hardwire Zone 7 Assignment I_ _I 01 to 24
308 Hardwire Zone 8 Assignment I_ _I 01 to 24
999 Default System 999 + TEST + 999 + TEST