Linear DF-16 SSD Defiant Dialer Program

P-9 Battery 3-volt Lithium DL2430
1700 Dialer is also known as DF-17 Dialer (if ordering new ones)
Linear
SSD signals
01 = Fire/Smoke Detector
02 = Panic Button/Keyfob Panic
03 = All Wireless Burg Sensors
Remote
Connection
1. At first Password prompt type PASS then ENTER
2. At next password prompt type 01 then ENTER
3. Display shows “File maintenance” press ENTER
4. Arrow up to “modify”, press ENTER
5. Select file 1 (for 2-way Systems) or 2 (Standard Systems, no 2-way) then ENTER
6. at “1700 Master file?” press “Y”
7. At “Select Step” select 1 then press ENTER
8. Press ENTER until you get to “Phone Number 1” enter Receiver Number, press ENTER
9. At “Account Number” enter 3 or 4 digit Account Number (depends on format) then ENTER
10. Press ESC , at “Save?” press Y
11. Arrow up to “Remote Comm” then press ENTER
12. Arrow up to “Write Comm” then press ENTER
13. Type Customer phone number then press ENTER
14. Enter Access Code (try 3193, needed if Dialer locked out in previous programming)
15. Programmer will dial phone, ring twice, hang up and call again, panel should answer
16. At “Enter File Number” Enter 1 or 2 (depending on system to be programmed)
Download will start then show “Set Time & Date?” press ESC to disconnect
Local
Connection
1. Do above Remote Connection steps, instead of “Remote Com” use “Local Com”
2. Plug in RJ Cord from panel directly into back of P9 Programmer
3. Arrow up to “Write Comm” then press ENTER
4. Display will say “Press button on Dialer” press Red button on TOP of Dialer Main board
5. Display asks “1 – 8?” select template to download, Programmer will being downloading
6. Press ESC when “Set Time & Date” prompt to disconnect
(Locked out Dialers allow downloading if using Local Connection method)

1700 Program Steps (Use ↑ or ↓ to toggle some locations, press Y or N for others)
You can only choose what step you want to start at when display asks “Select Step”
Step Description Value
01 Enter MF Header (Just a description of system)                    

02 Enable Telephone Comm ( Y/N ) Y

03 Enter Phone 1 ??????
Cntrl STA Format for Ph 1 Radi Hex (most common)
Sescoa Standard (3×1 report, Account number from 000 to 999)
Sescoa Super Speed (4×3 report, Account number from 0000 to 3374)
Radionics Hex (3×1 report, Account number from 000 to FFE (A is not used)
SEIA (Not supported by 1700 Dialer)
Enter Account for Ph 1 3-digits (4 if using Sescoa Fast)

04 Enter Phone 2 Not Used
Cntrl STA Format for Ph 2 Doesn’t Matter
Enter Account for Ph 2 Doesn’t Matter

05 Enter Phone 3A Not Used

06 Enter Phone 3B Not Used
Cntrl Sta Format for Ph 3 Doesn’t Matter
Enter Account # for Ph 3 Doesn’t Matter

07 Use DTMF Dialing ( Y/N ) Y
DTMF Fast Rate Dialing ( Y/N ) Y

08 Is Ground Start Required ( Y/N ) N

09 Enter Number of Call Tries 10

10 Enter Sleep Cycles ( 0 – 14 ) 2

11 Enter Sleep Time ( Min ) 4

12 Enter Anti-Jam Time ( 15 – 255 ) 30

13 Enter Loop Restoral Code Not Used

14 Supervisory Reports? ( Y/N ) Y

15 Enter Primary Superv Phone 1 1

16 Enter Secondary Superv Phone 4

17 Report To Both Number? ( Y/N ) N

18 Open or Close Reports? ( Y/N ) N

19 Open Signal Polarity + ? ( Y/N ) Y

20 Enter Open (Disarm) Code 0

21 Enter Close (Arm) Code 0

22 Send Test Code? ( Y/N ) N

23 Enter Test/Cancel Code 0

24 Are Battery Rpts Required? ( Y/N ) N

25 Enter Low Battery Code 0

26 Enter Battery Restoral? ( Y/N ) Y

27 Enter Battery Restoral Code 0

28 Enter Battery Detect Time Doesn’t Matter

29 Is 24Hr Check-In Required? ( Y/N ) N

30 Enter Check-In Code 0

31 Enter Loop 1-8 Select 1
LO1 – Active Loop? ( Y/N ) Y
LO1 – Trigger Polarity +? ( Y/N ) Y
LO1 – Eliminate Swingers? ( Y/N ) Y
LO1 – Enter E.S. Count ( 1-8 ) 3
LO1 – Primary Phone #? ( 1-3 ) 1
LO1 – Secondary Phone #? ( 1-3 ) 4
LO1 – Report To Both #’s? ( Y/N ) N
LO1 – Report Loop Restoral? ( Y/N ) N
LO1 – Enter Alarm Code ( 0 – 99 ) 01
LO1 – Enter Loop Response 0
LO1 – Enter Loop Priority ( 1-7H ) 7
LO1 – Audio Loop? ( Y/N ) Y if using 2-way
LO1 – Audio Listen Only? ( Y/N ) N

LO2 – Active Loop? ( Y/N ) Y
LO2 – Trigger Polarity +? ( Y/N ) Y
LO2 – Eliminate Swingers? ( Y/N ) Y
LO2 – Enter E.S. Count ( 1-8 ) 3
LO2 – Primary Phone #? ( 1-3 ) 1
LO2 – Secondary Phone #? ( 1-3 ) 4 (Why? I don’t know)
LO2 – Report To Both #’s? ( Y/N ) N
LO2 – Report Loop Restoral? ( Y/N ) N
LO2 – Enter Alarm Code ( 0 – 99 ) 02
LO2 – Enter Loop Response 0
LO2 – Enter Loop Priority ( 1-7H ) 6
LO2 – Audio Loop? ( Y/N ) Y if using 2-way
LO2 – Audio Listen Only? ( Y/N ) N

LO3 – Active Loop? ( Y/N ) Y
LO3 – Trigger Polarity +? ( Y/N ) Y
LO3 – Eliminate Swingers? ( Y/N ) Y
LO3 – Enter E.S. Count ( 1-8 ) 3
LO3 – Primary Phone #? ( 1-3 ) 1
LO3 – Secondary Phone #? ( 1-3 ) 4 (Why? I don’t know)
LO3 – Report To Both #’s? ( Y/N ) N
LO3 – Report Loop Restoral? ( Y/N ) N
LO3 – Enter Alarm Code ( 0 – 99 ) 03
LO3 – Enter Loop Response 0
LO3 – Enter Loop Priority ( 1-7H ) 5
LO3 – Audio Loop? ( Y/N ) Y if using 2-way
LO3 – Audio Listen Only? ( Y/N ) N

LO4 – Active Loop? ( Y/N ) N
LO5 – Active Loop? ( Y/N ) N
LO6 – Active Loop? ( Y/N ) N
LO7 – Active Loop? ( Y/N ) N
LO8 – Active Loop? ( Y/N ) N

32 RCM Direction
(Remote Control Module) ( Y/N )
N

33 Enable Remote Access? ( Y/N ) Y

34 Lock Communicator? ( Y/N ) N