GE Ultraguard Program – CMS Tech Help

Enter Program	1. Open and remove panel door, set PROGRAM/RUN switch down 2. Enter Installer Code (by default there is no Installer Code)
Exit Program	Set PROGRAM/RUN switch to UP
Default Panel	1. Turn Power Switch OFF then ON 2. Hold MEMORY CLEAR button on upper left, system says “Memory Goodbye”

Add Sensor

1. Press BYPASS or STATUS until LEARN SENSOR is displayed
2. Press COMMAND, keypad will display GROUP __ __
3. Enter GROUP <00 to 29, 32> + COMMAND button

Click HERE for complete list of Sensor Types

4. Keypad will show SENSOR ##, enter sensor <01 to 76>
5. Press COMMAND, keypad will read TRIP – ##, trip sensor
6. Once sensor is learned system will move to next sensor or activate Tamper
7. Press FIRE to exit
(Do not use SAW sensors on this system, use only older Learn Mode Sensors!)

Delete Sensor

1. Press BYPASS or STATUS until DELETE SENSOR is displayed
2. Press COMMAND button, Enter sensor to delete (01 to 76)
3. Press COMMAND button, keypad will show DEL ## OK
4. Press FIRE to exit

Add Touchpad

1. Press BYPASS or STATUS until LEARN TOUCHPADS is displayed
2. Press COMMAND button to display PRESS BYP TP-1
3. Press BYPASS on wireless touchpads and display will read One OK
4. Press FIRE to exit

Locations

BYPASS	scrolls forward
STATUS	scrolls back
COMMAND	enters Location and saves settings
FIRE	exits Location

– Delete Text

– Program Sensor Text

– Learn Sensors

– Delete sensors

– Upper Sensors

(Zones 77 and above)

– F Options

(Functions, see bottom of page)

– Learn Touchpads

(Learns wireless keypads)

– Phone Number

(18 digits, press Police Panic for 1 second pause)

– Phone Format

(ITI Format, 4/2 1400hz, 4/2 2300hz supported)

– Siren Time-out

(01 to 30 minutes)

– Install Code

(Default is blank)

– Account Number

(5 digits, A to F only programmed by CS-4000)

– Entry Delay

(008 to 120 seconds)

– Extended Delay (Exit)

(affects Group 11 sensors, 01 to 8 minutes)

– Exit Delay

(008 to 184 seconds)

– Activity Time-out

(01 to 24 hours)

– House Code

(001 (A) to 255 (P) Default = 001)

– Freeze Temperature

(40 to 90 degrees)

– Set Temperature

(32 to 99 degrees)

– Touchpad Options

– AVM Mode (Interrogator 2000)

01	– 1 ring callback mode
02	– 1 ring silent callback mode
03	– Instant Activation mode
09	– 1 Ring, Fire siren Shutdown
10	– One Ring Silent Fire Shutdown
11	– Instant Activation, Fire Siren Shutdown

– AVM Time-out (activation time)

(030 to 300 seconds in 2 second increments)

– AVM Code

(Blank/0001 to 9998, do not program this)

– HOM Setup

– Time Zone

05	– Eastern Time
06	– Central Time
07	– Mountain Time
08	– Pacific Time
10	– Hawaii Time

Functions

(can be enabled at keypad or by CS-4000, normally not needed)

F00	ON = Remote Phone Access Enabled after 12 rings	OFF = Remote Access Disabled
F01	ON = Ring/Hang/Ring enabled (download or phone)	OFF = Answers only after 12 rings
F02	ON = Exterior Siren sounds 15 seconds after alarm	OFF = Sounds immedately
F03	ON = Phone/Download access after 8 rings	OFF = Access after 12 rings
F04	ON = RF Low Battery reports once a week	OFF = Low Bat once per day
F05	ON = Sensor Supervisory reports once a week	OFF = Once per day
F06	ON = Dialer Aborts during alarm if disarmed	OFF = Reports even if disarmed
F07	ON = # is Phone Access key	OFF = * is Phone Access key
F11	ON = Hardwire interior siren sounds alarm	OFF = Sounds Alarm & Status
F12	ON = Alarm Restoral Reports enabled	OFF = Disabled
F13	ON = Low RF Battery Restoral Reports enabled	OFF = Disabled
F14	ON = Hourly Phone Test enabled (TLM)	OFF = Disabled
F15	ON = Alarm Verification (2 zones must trip for report)	OFF = Disabled
F16	ON = RF Trouble Beeps but allows Arming	OFF = Will not allow arming
F17	ON = Sensor Tamper causes Alarm	OFF = Disabled
F20	ON = AVM Interrogator Active	OFF = AVM is Disabled
F21	ON = Immediate Trouble Beeps	OFF = Trouble Beeps in 10 Hours
F22	ON = DTM Disaling enabled	OFF = Pulse Dialing Enabled
F23*	ON = Arm/Disarm & Time Change to Event Buffer	OFF = All Events saved to Event Buffer
F25	ON = Keyfob arms to level 3	OFF = Keyfob arms level 1, 2 then 3
F32	ON = Keyfob * arms no delay	OFF = Turns ESM On or Off
F33	ON = Downloader Access enabled	OFF = Disabled
F35	ON = Phone Panics enabled (7777, 8888, *9999)	OFF = Disabled
F36	ON = Local Phone Access enabled	OFF = Access disabled
F37	ON = Quick-Arm enabled	OFF = Quick-Arm disabled
F40*	ON = Fire Zone must trip twice for Alarm	OFF = Only trips once for Alarm
F41	ON = Interior Siren Trouble shows on Keypad	OFF = Interior Siren not Supervised
F42	ON = Sensor 70 to 80 Alarm tracking enabled	OFF = Disabled
F43*	ON = Demo Kit Enabled	OFF = Disabled
F44*	ON = Exterior Siren Latched when in Alarm	OFF = Disabled
F45*	ON = Zone 1 Keyswitch Arm/Disarm	OFF = Zone 1 Normal
F46*	ON = Daylight Savings Enabled	OFF = Disabled
F47	ON = 4-Hour Silence on Fire Troubles	OFF = Disabled

* = UltraGard v2 Only

Upper Sensor Numbers
77 = Touchpad Tamper
78 = Freeze Sensor
79 = No Activity
80 = Keypad Fire
81 = Keypad Police
82 = Keypad Medical/Aux
83 = Phone Test
84 = Opening Report
85 = Closing Report
86 = Duress Alarm
87 = Force Arm
88 = Energy Saver Enable
89 = RF Touchpad Supervisory or Low Battery
90 = AC Power Failure
91 = Low Panel Battery
92 = Panel Tamper
93 = Auto Phone Test
94 = Wireless Receiver Failure
95 = CPU Back in Service (AC Restoral)
96 = Phone Failure
98 = Events Report

CS-4000 Commands

ACCT or ACCOUNT

<XX-XX>

Account Number (0 as 1st digit if 4-digit account)

ACCESS

<4-digits>

Programs Master Code

ALARMQ

Views last 6 events of Alarm history

ANS

1 Connects CS-4000 to Panel

BATTLIFE

<1 to 30>

Battery Life? in Hours

BYPASS or BYP

(00 to 16)

Bypasses Sensors

CPUTIME

(SET/STATUS)

SET Sets panel time, STATUS reads panel time

DELETE or DEL

(00 to 16)

Deletes Sensors

DURESS

<00 to 99>

Hostage/Duress Code (usually 99)

ENTRY

<8 to 88>

Entry Delay (seconds)

EXIT

<8 to 88>

Exit Delay (seconds)

GROUP

Changes Zone type

Freeze	GROUP <zone> 01 L
Fire	GROUP <zone> 02 D
Delay	GROUP <zone> 04 L
Instant	GROUP <zone> 05 L
Interior Inst Follower	GROUP <zone> 06 L
Interior Follower	GROUP <zone> 06 I
Silent Police Panic	GROUP <zone> 12 A
Audible Medical Panic	GROUP <zone> 01 B

HOUSE

<1 to 255>

Views House Code

INIT

<00 to 16>

Initializes Sensors

MACCESS

<2 to 6> <4 digits>

Programs Secondary Codes
(Commander 8 only has 1 secondary Code)

PLOCK

???? %XXXXXXXX

Changes Installer Code
???? = Old Installer Code
XXXX = New Installer Code Twice

PFORMAT

<0 to 2>

Report Format (0=ITI, 1=4×2, 1400hz, 2=4/2, 2300hz)

PHONE

<7 to 4 digits>

Primary Receiver (D = Pause)

PHONE2

<7 to 4 digits>

Secondary Receiver (Commander 17 only)

PLEVEL

<1 to 3>

Changes Arming Level
PLEVEL 1 = Disarm
PLEVEL 2 = Arm Home
PLEVEL 3 = Arm Away

RECALL

Has panel disconnect then call back

REL

Releases Panel from CS-4000

SIREN

<1 to 9>

Siren Timeout in Minutes

STIME

<hh:mm>

Supervisory Report Time

UPD

Sends updated programming to panel

ZONES

Lists all Zones including Panics & Supervisory