1. Home
  2. GE ITI
  3. GE FoneSafe
  4. GE FoneSafe
 

GE / ITI / UC FoneSafe Program

V3 + systems are rare, have external AC transformer, can use standard ITI wireless
Most programing is done at house, communicator programming done by CS-4000 Receiver
Enter Program PROGRAM + INSTALLER CODE
Exit Program RESET
Exit Location RESET
Program Step 1 (With CS-4000 Receiver)

1. Call house while on CS-4000 Phone line
2. Have Tech press PROGRAM + INSTALLER CODE + 8 (Forces FonSafe online)
(If Installer Code is not known trip alarm)
3. Program Account Number then ENTER (ACCOUNT ??-???)
4. Program Receiver Number then ENTER (PHONE ??????????)
5. Program Installer Code then ENTER (IACCESS ????)
6. Program Master Code then ENTER (ACCESS ????)
7. Enable Installer Programming (INSTALLMODE ON)
8. Enter REL then ENTER (Releases FonSafe)
9. Call tech back, have him disconnect FonSafe from phone line
(You cannot program anything in panel if phone line is still connected)
Program Step 2 (Most of the below locations don’t need to be programmed)
1. Press PROGRAM + INSTALLER CODE to enter programming
2. Enter locations below (example, for Duress press 3 then 3 then 99)
Description Location Values
TIMES
Time (Clock) 1, 1 (4-Digit HH MM Press 1 for AM, 2 for PM)
Program Timed Lights 1, 2 (Only if X-10 is used)
Program Timed Options 1, 3 (Only if X-10 is used)
Entry/Exit Time 1, 4 (Enter 2-Digit Entry + 2-Digit Exit seconds)
Siren Timeout 1, 5 (10 to 20 minutes)
SENSOR PROGRAMMING
Learn New Sensor/Detector 2, 1, 1
Delete Sensor/Detector 2, 1, 2
Change Sensor Description 2, 1, 3
Change Sensor Arming Level 2, 1, 4
Change Sensor Delay 2, 1, 5
Change Sensor Siren Level ON 2, 1, 6, 1     (Makes it Audible)
Change Sensor Siren Level OFF 2, 1, 6, 2 (Makes it Silent)
Change Sensor Call Option ON 2, 1, 7, 1 (Reports to CS)
Change Sensor Call Option OFF 2, 1, 7, 2 (Sensor is Local Alarm only)
List all Sensor Programming 2, 1, #
LIGHTS/APPLIANCE MODULES
Program or Change Lights 2, 2, 1 (Only if X-10 is used)
Program or Change Options 2, 2, 2 (Changes Appliance Modules)
Delete Lights 2, 2, 3, 1
Retain Lights 2, 2, 3, 2
Delete Appliance Module 2, 2, 4, 1
Retain Appliance Module 2, 2, 4, 2
Change Lights House Code 2, 2, 5, 1 (2-Digits)
Change Appliance House Code 2, 2, 5, 2
Change Siren House Code 2, 2, 5, 3
List all House Codes 2, 2, 5, #
PASSWORDS/USER CODES
Master Code 3, 1 (4-Digits)
Secondary Code 3, 2 (4-Digits)
Duress Code 3, 3 (00 to 99)
Installer Code 3, 4 (4-Digits)
SYSTEM/PHONE OPTIONS
CS Phone 1 5, 1, 1
CS Phone 2 5, 1, 2
System Account Number 5, 2 (5-Digits #01 = A #14 = S etc)
Sensor Status Supervisory Time 5, 3 (Enter Wireless Supervisory in Hours)
Customer Home ID Code 5, 4 (I have no idea what this does)
DTMF Dialing ON 5, 5, 1
DTMF Dialing OFF 5, 5, 2
Motion Activity Timer Fail Time 5, 6, 1 (Time for Report if Motion not activated)
Phone Activity Monitoring ON 5, 6, 2, 1 (Resets Activity Timer if Phone off Hook)
Phone Activity Monitoring OFF 5, 6, 2, 2 (Disables)
Motion Monitors Activity ON 5, 6, 3, 1 (PIR trip resets Activity Timeout)
Motion Monitors Activity OFF 5, 6, 3, 2 (Motion trips are ignored)
Cancel Report Enabled 5, 7, 1
Cancel Report Disabled 5, 7, 2
Keypad Sensor Arm Option ON 5, 8, 1, 1 (Touchpad arms AWAY with NO DELAY)
Keypad Sensor Arm Option OFF 5, 8, 1, 2 (Touchpad first arms HOME then AWAY)
Sensor Front Open Option ON 5, 9, 1 (Enables Sensor Tampers)
Sensor Front Open Option OFF 5, 9, 2 (No Sensor Tamper Monitoring)
PROGRAM MCU OPTIONS
Local, No Phone Line Supervision 7, 1 (Local System, No Line Monitoring)
Monitored, no Phone Supervision 7, 2 (Monitored, Phone Monitoring)
Monitored, Phone Superv w/Status 7, 3 (Monitored, Phone Monitoring, Status Message)
Monitored, Phone Superv w/Alarm 7, 4 (Monitored, Phone Monitoring, Local Alarm)
Toggle Phone 2-Way Voice Support 7, 5 (Enables Interrogator Module)
Toggle RG Phone (Remote Answer) 7, 9 (Beats me what this is)
DOWNLOADING OPTIONS
Enable CS Download 8 (Connects to CS-4000)
PC Download 9 (Beats me)
Learn Sensor
1. Enter Programming with PROGRAM key + MASTER CODE
2. Press 2 to select “Program Sensor, Light or Option”
3. Press 1 to select “Program Sensor, press 1” press 1 again
4. System says “Trip Sensor 1” now trip sensor

Door/Window Sensors (Open zone)
Remote Keypad (Press 0)
Smoke Detector (Press TEST on Smoke until activation)
Motion Detector (Move in front of Motion)
5. System says “Sensor 1 learned OK” Press # to move to next step
6. System says “Please enter Sensor Code” enter from list below then #

1 = Door Sensor 5 = Freeze Detector
2 = Window Sensor 6 = Flood Sensor
3 = Motion Detector 7 = Glass Break Detector
4 = Heat/Smoke 8 = Utility
7. System says “Please enter Description Number” , enter Description Number then #

0 = No description 10 = Living Room 20 = Downstairs
1 = Bedroom 1 11 = Dining Room 21 = Hall
2 = Bedroom 2 12 = Guest Room 22 = Front Hall
3 = Bedroom 3 13 = Laundry Room 23 = Kitchen
4 = Bedroom 4 14 = Utility Room 24 = Office
5 = Master Bedroom 15 = Front Door 25 = Basement
6 = Child’s Bedroom 16 = Back Door 26 = Garage
7 = Guest Bedroom 17 = Garage Door 27 = Attic
8 = Bathroom 18 = Basement Door 28 = Closet
9 = Master Bathroom 19 = Upstairs 29 = Den
8. System says Enter Sensor Armed Level” enter lowest level sensor will Arm

OFF = Always Armed (Fire or 24 hour zones)
HOME = Arms in HOME and AWAY (Usually Perimeter only)
AWAY = Arms only in AWAY (Usually Motions only)
9. “For Sensor Delay press 1, For sensor Not Delay press 2” then press #

1 = Entry/Exit Zones
2   = Instant Zones
10. System speaks new Sensor Programming, trip next sensor or RESET to exit
Delete Sensor 1. Enter Programming with PROGRAM key + MASTER CODE
2. Press 2 to select “Program Sensor, Light or Option”
3. Press 1 to select “Learn Sensor, press 1” press 2 instead
4. Press 2 to select “Delete Sensor”
5. Press RESET twice to exit programming
Interrogator Programming
From Panel 1. Press PROGRAM + Master Code
2. Press 7 + 5 to enable Interrogator support (it should say ON I think)
3. Press RESET to exit FonSafe programming
Then
Remote (if you don’t get this right the 1st time you must wait 15 minutes)

1. Assume the tech has no Butt Set, its easier to program like this anyway
2. Call panel on regular phone, let ring twice
3. Hang up, wait 10 seconds and call back, FonSafe picks up on 2nd ring
4. Enter Master Code at prompt, panel will announce menu options
5. Press * * 0, Interrogator says Goodbye (if hangs up FonSafe isn’t setup right)
6. Press * (1 beep) to enter Programming
or go 2-way with Customer (1=Talk, 3=Listen, 99=Disconnect)
7. Press * + # + 10 + 1234 + # (Enters Interrogator Programming)
8. Press * + # + 39 + 2 + # (Adds Interrogator to Fonsafe)
9. Press * + # + 40 + 2 + 0 + # (2=ITI Trip, 0=Link Mode, 4=Callback)
10. Press 99 to exit and disconnect
OR
Locally 1. Connect butt-set to Program Post and Diode on Interrogator (See diagram)
2. Buttset must be clipped to loop of wire that extends from top of diode down to circuit board
3. Power up panel and Interrogator
4. Move programming jumpers to programming positions
  (Move vertical jumper down. Move horizontal jumper to left)
5. Enter Programming by * + # + 10 + 1234 + # (see program sheet on bottom of page)
6. Press 99 to exit then move vertical jumper Up, horizontal jumper Right
Program Sheet (Usually programming here is never needed, leave alone)
* + # + 10 + 1234 + # Enters Interrogator Programming
* + # + 11 + # + 0 or 1 Turn Aux Output OFF (0) or ON (1)
* + # + 12 + # Retreives Account Number in DTMF format (default 1234)
* + # + 30 + ???? + # Set Interrogator Login Password
* + # + 31 + 0 or 1 + # Set Dialing format for Pulse (0) or DTMF (1)
* + # + 32 + ??? + # Phone Number (up to 20 digits, for pause hold 7 for 5 seconds)
* + # + 33 + 0 or 1 + # Off site Accessing OFF (0) or ON (1)
* + # + 38 + ???? + # Interrogator 5-digit Account Number
* + # + 39 + ? + # Set Control panel type connected to Interrogator
1 = (Default) 2 = FonSafe
* + # + 40 + X + Y + #
Trip Input Trip Action
X = Trip Input Y = Trip Action
0 = Falling edge 0 = Instant ON, Activation Beeps
1 = Rising edge (SX-V) 1 = Instant ON, no Activation Beeps
2 = ITI Trip 2 = Callback, answer on 1st ring
(Caretaker Plus, Com 2000) 3 = Dial out after trip detect
4 = Callback, No On-site phone ring
* + # + 41 + > + # Interrogator Aux output option Disabled (0) or Enabled (1)
* + # + 42 + X + # Auxiliary Output Time/Recording Save Time

X = Aux Output Time 0 = 5 seconds
1 = 10 seconds
2 = 5 minutes
3 = 10 minutes
* + # + 44 + ? + # Switches hot-key assignments (0 or 1 default is 0)

Default is 0 = 0 Listen 4 Talk 7 Extend 9 Terminate
Switched is 1 = 1 Talk 3 Listen 7 Extend 9 Terminate
* + # + 49 + # Clears Memory, defaults Interrogator