GE / ITI / UC Concord Program

Click HERE for Programming Keys
Must be programmed with 60-746 Alpha Keypad (Green backlight)
Enter Program 1. While powered up plug in Programmer Keypad
2. Enable Programmer Keypad by entering 8 + Installer Code + 02
3. 8 + Installer Code + 00, keypad says “SYSTEM PROGRAMMING”
(Do not power up with Programmer connected to avoid Bus Errors later)
Move to
Location
From any menu (like SECURITY or GLOBAL) enter 4 or 5 digit “Shortcut”
(you cannot do this while IN a location)
Exit Program 1. Press * until “SYSTEM PROGRAMMING” appears
2. Press A or B keys until Keypad shows “EXIT PROGRAMMING” press #
3. Remove Programmer Keypad from connector on circuit board
Enable
Downloading
1. Press 9 + Master Code   (“SYSTEM MENU” then “USER CODES”)
2. Press * + 40 + 2 + #   (“Display shows “DOWNLOADING ON”)
3. Press * + 7 + # to exit
Send to
Downloader
Press 8 + Master or Installer Code + 7 + 0
Rescan Bus 8 + Installer Code + 01

Learn Sensor 1. Use shortcuts to go to location 080 (LEARN SENSORS) then press #
2. At “Sensor Partition” enter 1 or 2 then #
3. At “SENSOR GROUP” enter 2-digit Zone type then press #
CLICK HERE FOR COMPLETE LIST OF SENSOR TYPES
4. At “TRIP SENSOR xx” either learn by below or enter new Zone number then below

Door Sensor Remove cover (hardwired contacts learn while open)
Glassbreaks Make a lot of noise (keys, clap etc)
Motions Remove cover, may require pressing button
Heat Sensor Rub hands until warm, place on sensor 30 seconds
Smoke Hold Test button 30 seconds until Panel beeps
Keyfobs H old LOCK and UNLOCK buttons 3 seconds
Encrypted Keyfob Unlock twice then HOLD until LED flashes, do this 3 times
Touchpads Press BYPASS button for 3 seconds
Hardwired Zones Open Zone (Any Hardwire Zone can be Zones 01 to 24)
4. If learned correctly keypad will say “Sensor OK” and go to next sensor
(Panel continues to learn same group, to change press ** then re-enter group)

Delete Sensor 1. Use shortcuts to go to location 082 (DELETE SENSORS) then press #
2. At “DELETE SENSOR xx” enter 2-digit sensor to delete press #
3. Display will show “DELETE SENSOR xx DONE” press * to exit

Address Keypad 1. Press and hold D and 6 at same time
2. Display should show DA xx (xx = current address)
3. Press #, enter new 3-digit address (000 to 015 then press #
4. Press * to exit, then rescan bus with 8 + Installer Code + 01

Delete Unit ID (If Programmer was learned into system by power-up)
1. Enter programming, at “System Programming” press #
2. Press B key to move to “Accessory Modules” press #
3. Display shows “Bus Devices” press #
4. Display shows “Unit Type”
Second line shows “00 – LTP” (for LED Keypad) or “00 – ATP” (Alpha Keypad)

LTP = LED Keypad
ATP = Alpha Keypad
ESM = Energy Saver Module
HIM = Hardwire Input Module
HOM = Hardwire Output Module
PIV = Phone Interface & Voice Module
RCVR = Wireless Receiver
5. Press B to move to “01 – ATP” (should be location for Alpha programmer)
6. Press D to delete then * to exit
(If not sure which device it is delete everything (00 to 15), power down & back up)

Below locations are NOT COMPLETE but enough to do basic programming

SECURITY
GLOBAL   (# saves, * exits)
Location   Description Values Use Instead
0000 Downloader Code 12345
0001 Installer Code 4321
0002 Dealer Code None

PARTITION 1   (# saves, * exits)
Location Description Values Use Instead
0010 Partition One Account Number
(Press and Hold 1 to 6 for A to F)
(up to 10 digits) 00000 4 or 5-digits
0011 Quick Arm (1=OFF 2=ON) OFF
0012 Keyswitch Arming (1=OFF 2=ON) ON
0013 Duress Code (4 digits) NONE

PARTITION 2   (# saves, * exits)
Location Description Values Use Instead
0020 Partition Two Account Number
(Press and Hold 1 to 6 for A to F)
(up to 10 digits) 00000 4 or 5-digits
0021 Quick Arm (1=OFF 2=ON) OFF
0022 Keyswitch Arming (1=OFF 2=ON) ON
0023 Duress Code (4 digits) NONE

PHONES
CS PHONE 1   (# saves, * exits)
Location Description Values Use Instead
0100 CS Phone Number (up to 24 digits) None
(Press C for 3 second pause, D deletes, hold 7 for *, hold 9 for # )
0101 High Level Reports (1=OFF 2=ON) ON
0102 Low Level Reports (1=OFF 2=ON) ON
0103 Exception Reports (1=OFF 2=ON) ON
0104 Opening/Closing Reports (1=OFF 2=ON) OFF
0105 Backup Reporting ( 1=OFF 2=ON) ON
0106 Report Format (1=SIA 2=CID) CID SIA

CS PHONE 2  (# saves, * exits)
Location Description Values Use Instead
0110 CS Phone Number (up to 24 digits) NONE
(Press C for 3 second pause, D deletes, hold 7 for *, hold 9 for # )
0111 High Level Reports (1=OFF 2=ON) ON
0112 Low Level Reports (1=OFF 2=ON) ON
0113 Open/Close Reports (1=OFF 2=ON) OFF
0114 Opening/Closing Reports (1=OFF 2=ON) OFF
0115 Backup Reporting (1=OFF 2=ON) ON
0116 Report Format (1=SIA 2=CID) CID SIA

CS PHONE 3   (# saves, * exits)
Location Description Values Use Instead
0120 CS Phone Number (up to 24 digits) NONE
(Press C for 3 second pause, D deletes, hold 7 for *, hold 9 for # )
0121 High Level Reports (1=OFF 2=ON) ON
0122 Low Level Reports (1=OFF 2=ON) ON
0123 Open/Close Reports (1=OFF 2=ON) OFF
0124 Opening/Closing Reports (1=OFF 2=ON) OFF
0125 Backup Reporting (1=OFF 2=ON) ON
0126 Report Format (1=SIA 2=CID) CID SIA

PAGER PHONE 1   (# saves, * exits)
Location Description Values Use Instead
0130 Phone Number (up to 24 digits) NONE
(Press C for 3 second pause, D deletes, hold 7 for *, hold 9 for # )
0131 High Level Reports (1=OFF 2=ON) OFF
0132 Low Level Reports (1=OFF 2=ON) OFF
0133 Exception Reports (1=OFF 2=ON) OFF
0134 Opening/Closing Reports (1=OFF 2=ON) OFF
0135 Latchkey Reports (1=OFF 2=ON) ON
0136 Streamlining (1=SIA 2=CID) ON
0137 Partition Assignment (1, 2 or 1 & 2) 1

PAGER PHONE 2   (# saves, * exits)
Location Description Values Use Instead
0140 Phone Number (up to 24 digits) NONE
(Press C for 3 second pause, D deletes, hold 7 for *, hold 9 for # )
0141 High Level Reports (1=OFF 2=ON) OFF
0142 Low Level Reports (1=OFF 2=ON) OFF
0143 Exception Reports (1=OFF 2=ON) OFF
0144 Opening/Closing Reports ( 1=OFF 2=ON) OFF
0145 Latchkey Reports (1=OFF 2=ON) ON
0146 Streamlining (1=SIA 2=CID) ON
0147 Partition Assignment (1, 2 or 1 & 2) 1

PAGER PHONE 3   (# saves, * exits)
Location Description Values Use Instead
0150 Phone Number (up to 24 digits) NONE
(Press C for 3 second pause, D deletes, hold 7 for *, hold 9 for # )
0151 High Level Reports (1=OFF 2=ON) OFF
0152 Low Level Reports (1=OFF 2=ON) OFF
0153 Exception Reports (1=OFF 2=ON) OFF
0154 Opening/Closing Reports (1=OFF 2=ON) OFF
0155 Latchkey Reports (1=OFF 2=ON) ON
0156 Streamlining (1=SIA 2=CID) ON
0157 Partition Assignment (1, 2 or 1 & 2) 1

PAGER PHONE 4   (# saves, * exits)
Location Description Values Use Instead
0160 Phone Number (up to 24 digits) NONE
(Press C for 3 second pause, D deletes, hold 7 for *, hold 9 for # )
0161 High Level Reports (1=OFF 2=ON) OFF
0162 Low Level Reports (1=OFF 2=ON) OFF
0163 Exception Reports (1=OFF 2=ON) OFF
0164 Opening/Closing Reports (1=OFF 2=ON) OFF
0165 Latchkey Reports (1=OFF 2=ON) ON
0166 Streamlining (1=SIA 2=CID) ON
0167 Partition Assignment (1, 2 or 1 & 2) 1

PAGER PHONE 5   (# saves, * exits)
Location Description Values Use Instead
0170 Phone Number (up to 24 digits) NONE
(Press C for 3 second pause, D deletes, hold 7 for *, hold 9 for # )
0171 High Level Reports (1=OFF 2=ON) OFF
0172 Low Level Reports (1=OFF 2=ON) OFF
0173 Exception Reports (1=OFF 2=ON) OFF
0174 Opening/Closing Reports (1=OFF 2=ON) OFF
0175 Latchkey Reports (1=OFF 2=ON) ON
0176 Streamlining (1=SIA 2=CID) ON
0177 Partition Assignment (1, 2 or 1 & 2) 1

DOWNLOADER PHONE   (# saves, * exits)
0180 Phone Number (up to 24 digits) NONE
(Press C for 3 second pause, D deletes, hold 7 for *, hold 9 for # )

PHONE OPTIONS
GLOBAL   (# saves, * exits)
Location Description Values Use Instead
0200 Phone Test (1=OFF 2=ON) ON
0201 Auto Phone Test (1=OFF 2=ON) OFF
0202 Comm Failure (1=OFF 2=ON) ON
0203 DTMF Dialing (1=OFF 2=ON) ON
0204 Dialer Abort (1=OFF 2=ON) ON
0205 Pager Delay (0 to 255 sec) 15

PARTITION 1   (# saves, * exits)
Location Description Values Use Instead
0210 Remote Access (1=OFF 2=ON) ON
0211 Ring/Hang/Ring (1=OFF 2=ON) ON
0212 Hourly Line Test (1=OFF 2=ON) OFF
0213 Toll Saver (1=OFF 2=ON) ON
0214 Phone Panic (1=OFF 2=ON) OFF
0215 Phone ACC (Access) Key (1 = * 2 = #) #

PARTITION 2   (# saves, * exits)
Location Description Values Use Instead
0220 Remote Access (1=OFF 2=ON) ON
0221 Ring/Hang/Ring (1=OFF 2=ON) ON
0223 Toll Saver (1=OFF 2=ON) ON
0224 Phone Panic (1=OFF 2=ON) OFF
0225 Phone ACC (Access) Key (# or *) #

TIMERS
GLOBAL   (# saves, * exits)
Location Description Values Use Instead
0300 Supervisory Time (00:00 to 23:99) 00:00
0301 RF Tx Timeout (2 to 24 Hours) 12
0302 Phone Test Frequency (01 to 255 Days) 07
0303 Next Phone Test (01 to 255 Days) 07
0304 Output Trip Time (01 to 12 sec) 04
0305 Activity Timeout (01 to 42 Hours) 24
0306 Daylight Savings (1=OFF 2=ON) ON

PARTITION 1   (# saves, * exits)
Location Description Values Use Instead
0310 Entry Delay (32 to 240 sec) 32
0311 Exit Delay (48 to 184 sec) 64
0312 Extended Delay (1 to 8 min) 4
0313 Siren Timeout (1 to 30 min) 4

PARTITION 2   (# saves, * exits)
Location Description Values Use Instead
0320 Entry Delay (32 to 240 sec) 32
0321 Exit Delay (48 to 184 sec) 64
0322 Extended Delay (1 to 8 min) 4
0323 Siren Timeout (1 to 30 min) 4

LIGHT CONTROL
PARTITION 1   (# saves, * exits)
Location Description Values Use Instead
0400 Entry Lights 23456789
0401 House Code 01-B

PARTITION 2   (# saves, * exits)
Location Description Values Use Instead
0410 Entry Lights 23456789
0411 House Code 01-B

TOUCHPAD OPTIONS
GLOBAL   (# saves, * exits)
Location Description Values Use Instead
0500 RFTP Supervision (1=OFF 2=ON) OFF

PARTITION 1   (# saves, * exits)
Location Description Values Use Instead
0510 Fire Panic (1=OFF 2=ON) ON
0511 Auxiliary Panic (1=OFF 2=ON) ON
0512 Police Panic (1=OFF 2=ON) ON
0513 Keychain Touchpad (1=OFF 2=ON) OFF
0514 Keychain Star is No Delay (1=OFF 2=ON) OFF

PARTITION 2  (# saves, * exits)
Location Description Values Use Instead
0520 Fire Panic (1=OFF 2=ON) ON
0521 Auxiliary Panic (1=OFF 2=ON) ON
0522 Police Panic (1=OFF 2=ON) ON
0523 Keychain Touchpad (1=OFF 2=ON) OFF
0524 Keychain Star is No Delay (1=OFF 2=ON) OFF

REPORTING
GLOBAL   (# saves, * exits)
Location Description Values Use Instead
06000 24 Hour Tamper (1=OFF 2=ON) OFF
06001 Buffer Control (1=OFF 2=ON) OFF
06002 AC Back in Service (1=OFF 2=ON) ON
06003 Low CPU Battery (1=OFF 2=ON) ON
06004 Battery Restoral (1=OFF 2=ON) OFF
06005 Buffer Full Report (1=OFF 2=ON) OFF
06006 Zone Restorals (1=OFF 2=ON) OFF (Only wireless smokes will send restores)
06007 AC Failure (1=OFF 2=ON) OFF
06008 Receiver Fail (1=OFF 2=ON) OFF
06009 RF Low Battery Report (OFF=Day ON=Week) ON

PARTITION 1   (# saves, * exits)
Location Description Values Use Instead
0610 Opening Reports (1=OFF 2=ON) OFF
0611 Closing Reports (1=OFF 2=ON) OFF
0612 No Activity (1=OFF 2=ON) OFF
0613 Duress Option (1=OFF 2=ON) OFF
0614 Force Armed (1=OFF 2=ON) OFF
0615 Latchkey (1=OFF 2=ON) OFF
0616 Freeze Alarm (1=OFF 2=ON) OFF
0617 Alarm Verify (1=OFF 2=ON) OFF
0618 System Tamper (1=OFF 2=ON) OFF

PARTITION 2   (# saves, * exits)
Location Description Values Use Instead
0620 Opening Reports (1=OFF 2=ON) OFF
0621 Closing Reports (1=OFF 2=ON) OFF
0622 No Activity (1=OFF 2=ON) OFF
0623 Duress Option (1=OFF 2=ON) OFF
0624 Force Armed (1=OFF 2=ON) OFF
0625 Latchkey (1=OFF 2=ON) OFF
0626 Freeze Alarm (1=OFF 2=ON) OFF
0627 Alarm Verify (1=OFF 2=ON) OFF
0628 Siren Tamper (1=OFF 2=ON) OFF

SIREN OPTIONS
GLOBAL   (# saves, * exits)
Location Description Values Use Instead
0700 Immediate Trouble Beeps (1=OFF 2=ON) OFF
0701 Disable Trouble Beeps (1=OFF 2=ON) OFF
0702 UL 98 Option (1=OFF 2=ON) OFF
0703 SWS Supervision Code (1 to 255) ON
(System House Code for Supervised Wireless Sirens)
0704 Global Fire Siren (1=OFF 2=ON) OFF

PARTITION 1   (# saves, * exits)
Location Description Values Use Instead
0710 Siren Verify (1=OFF 2=ON) OFF

SENSORS
Location Description
080 Learn Sensors
081 Sensor Text   Click HERE for all Alpha Zone List
Display shows Sn 01 ITEM 00
Enter 3-digit description from list or scroll list with B and A
Press # to save and move to next word or character (up to 16 total)
When finished press * to save and exit

082 Delete Sensor   (Enter sensor then # to delete, * to exit)
083 Edit Sensor Group (Enter sensor, edit sensor Group, # saves, * exits)

Learn Sensor
1. Use shortcuts to go to location 080 (LEARN SENSORS) then press #
2. At “Sensor Partition” enter 1 or 2 then #
3. At “SENSOR GROUP” enter 2-digit Zone type then press #
CLICK HERE FOR COMPLETE LIST OF SENSOR TYPES
4. At “TRIP SENSOR xx” either learn by below or enter new Zone number then below

Hardwired Zones Trip by opening or activating sensor
Door Sensor Remove cover (hardwired contacts learn while open)
Glassbreaks Make a lot of noise (keys, clap etc)
Motions Remove cover, may require pressing button
Heat Sensor Rub hands until warm, place on sensor 30 seconds
Smoke Hold Test button 30 seconds until Panel beeps
Keyfobs Hold LOCK and UNLOCK buttons 3 seconds
Encrypted Keyfob Unlock twice then HOLD until LED flashes, do this 3 times
Touchpads Press BYPASS button for 3 seconds
Hardwired Zones Open Zone (Any Hardwire Zone can be Zones 01 to 24)
4. If learned correctly keypad will say “Sensor OK” and go to next sensor
(Panel continues to learn same group, to change press ** then re-enter group)
Delete Sensor 1. Use shortcuts to go to location 082 (DELETE SENSORS) then press #
2. At “DELETE SENSOR xx” enter 2-digit sensor to delete press #
3. Display will show “DELETE SENSOR xx DONE” press * to exit
AUDIO VERIFICATION
PARTITION 1
Location Description Values
0900 Audio Verify (1=OFF 2=ON) Off
0901 Audio Mode (B selects) 01 01 = Instant
02 = Callback
03 = Silent Callback
0902 Fire Shutdown (1=OFF 2=ON) Off
0903 Silent Talkback (1=OFF 2=ON) Off
0904 Access Timeout (30 to 300 sec) 90
0905 Beep Delay (0 to 300 sec) 02
0906 AVM Callback Access Code (4 Digits) None

BUS DEVICES
DELETE UNIT ID   (If Programmer was learned into system by power-up)

1. Enter programming, at “System Programming” press #
2. Press B key to move to “Accessory Modules” press #
3. Display shows “Bus Devices” press #
4. Display shows “Unit Type”
Second line shows “00 – LTP” (for LED Keypad) or “00 – ATP” (Alpha Keypad)

LTP = LED Keypad
ATP = Alpha Keypad
ESM = Energy Saver Module
HIM = Hardwire Input Module
HOM = Hardwire Output Module
PIV = Phone Interface & Voice Module
RCVR = Wireless Receiver
5. Press B to move to “01 – ATP” (should be location for Alpha programmer)
6. Press D to delete then * to exit
(If not sure which device it is delete everything (00 to 15), power down & back up)
ONBOARD OPTIONS
INPUTS   (# saves, * exits)
Location Description Values Use Instead
1100 Smoke Verification (1=OFF 2=ON) OFF
1101 2-Wire Smoke Enable (1=OFF 2=ON) OFF
(If enabling 2-Wire Smoke this option must be enabled first before learning sensors!)

ACCESSORY MODULES
(If SuperBus Output Relay Module 60-770 is installed)
RELAY 1
Location Description Values Use Instead
00100 Config Number 00100

RELAY 2
Location Description Values Use Instead
00500 Config Number 00500

RELAY 3
Location Description Values Use Instead
00200 Config Number 00100

RELAY 4
Location Description Values Use Instead
00300 Config Number 00100