| Zones |
| Concord Hybrid |
= 8 Hardwired, Wireless added by external Receiver only |
| Concord Integrated |
= 8 Hardwired and 16 or 32 Wireless, up to 76 total |
| (Hybrid panels show 55-702E printed on main board, Integrated shows 55-7743) |
|
| AC Transformer |
24 volt |
| Batteries |
| Main Panel |
12 volt rechargeable Gel-Cell |
| Door/Window |
2 “AAA” Alkaline or 3.6 volt Lithium (LS14250) |
| Glassbreaks |
2 “AA” 3.6 volt Lithium or 1 3.6 Lithium (LS14250) |
| Keyfob |
12 Volt Alkaline |
| Motion |
1 or 2 “AA” Alkaline |
| Smoke |
2 9-volt Alkaline |
|
| Partitions |
2 |
| Downloadable |
Yes Note: Cannot be armed/disarmed through download |
Enable
Downloading
|
| 1. Press 9 + Master Code |
(“SYSTEM MENU” then “USER CODES”) |
| 2. Press * + 40 + 2 + # |
(“Display shows “DOWNLOADING ON”) |
| 3. Press * + 00 + # to exit |
|
| Panic Buttons |
| A and 1 |
Police Panic |
| B and 4 |
Medical Panic |
| C and 7 |
Police Panic |
|
| Away Arm |
Press 3 (AWAY) + User Code |
| Stay Arm |
2 (STAY) + User Code |
| Instant Arm |
Arm with 2 (STAY) or 3 (AWAY) + User Code then press 4 (NO DELAY) |
| Quick Exit |
While Armed press D key to allow leaving without disarming for 2 minutes |
| Silent Arm |
Press 5 then Arm with above steps for no beeps on keypad during Arming |
| Disarm |
1 + User Code |
| Silence Alarm |
1 + User Code, press * to view Alarm Memory |
| Reset Smoke |
1 + User Code twice |
| Check Status |
Press * key once for short status message, ** twice for Full Status
(Full Status shows AC Power and Battery Status)
|
Move to other
Partition
|
1. Press 8 + User Code + 6
2. Press 1 to move to Partition 1, 2 for Partition 2
3. Arm, Disarm normally, keypad moves back to original partition
if no key is pressed in 10 seconds
|
| Bypass |
| 1. Arm system, press # + User Code |
(Keypad shows “ENTER Snsr”) |
| 2. Enter Zone to bypass (01 to 76) |
(Keypad shows “Snsr XX BYPASSED”) |
|
| Force Bypass |
| 1. Open zone then arm system |
| 2. Keypad will beep rapidly |
(Keypad shows “PROTEST”) |
| 3. Press # |
(Keypad shows “Snsr XX BYPASSED”) |
| 4. System will finish Arming |
|
| Set Time/Date |
| 1. Press 9 + Master Code |
| 2. Press * + 20 + 4-Digit Military Time + # |
(1:30PM = 13:30) |
| 3. Press * + 21 + 6-Digit Date + # |
(July 2nd 2001 = 070201) |
| 4. Press * + 00 + # to exit |
|
| Door Chimes |
Press 7 + 1 to turn On or Off (Keypad shows “CHIME IS ON or OFF”) |
| Voice Chime |
Press * + 044 + 1 ON or 2 OFF + # (Not available if system doesn’t talk) |
| Alarm Memory |
Press 7 + 6 (Entire Event Buffer viewed by downloading) |
| Energy Saver |
Press 7 + 2 |
| Output Control |
Press 7 + 7 + (1 to 6) |
| Phone Test 8 |
(SYSTEM) + Master Code + 2, press * after test finishes |
| Sensor Test |
1. Press 8 + Master Code + 3
2. Keypad shows “Armed to Sensor Test”, beeps every 60 seconds
3. Open Door or Window, move by motion
4. Press * to view any untested sensors
5. Press 1 + Master Code to end
(Wireless motions require no movement for 4 minutes prior to testing)
|
Disable/Enable
Arming Beeps
|
| 1. Press 9 + Master Code |
(“SYSTEM MENU” then “USER CODES”) |
| 2. Press * + 41 |
(“Display shows “SILENT ARMING”) |
| 3. Press 1 to turn Beeps ON or 2 for OFF |
| 4. Press # to save, * + 00 + # to exit |
|
Keypad
Brightness
|
| 1. Press 9 + Master Code |
(“SYSTEM MENU” then “USER CODES”) |
| 2. Press * + 42 |
(“Display shows “TOUCHPAD BRIGHTNESS”) |
| 3. Press 1# for Dim 2# for Medium 3# for Brightest |
| 4. Press * + 00 + # to exit |
|
| Keypad Volume |
1. Press * and 0 until steady tone
2. Press and hold 1 to lower pitch
or press and hold 2 to lower pitch
3. When desired tone sounds release
4. Keypad returns to normal in 15 seconds
|
| Remote Access |
1. Call house and let phone ring 1 time
2. Hang up and wait 20 seconds then call again
3. Panel should answer by saying “System Hello”
4. Press # and enter User Code, panel should say “System is OK”
(If it doesn’t then User Code’s access level isn’t high enough)
| # |
Check Status |
| # + ** |
Check Detailed Status |
| # + 1 + User Code |
Disarms system |
| # + 2 + User Code |
Arm Doors/Windows only (STAY) |
| # + 2 + User Code + 4 |
Arm Doors/Windows only (STAY+ INSTANT) |
| # + 2 + User Code + 6 |
Arm Doors/Windows to LATCHKEY |
| # + 3 + User Code |
Arm entire system (AWAY) |
| # + 3 + User Code + 4 |
Arm entire system (AWAY + INSTANT) |
| # + 3 + User Code + 6 |
Arm entire system to LATCHKEY |
| # + # + User Code + 01 to 76 |
Bypasses Sensor 01 to 76 |
| # + 1 + User Code |
Cancels an alarm |
| # + 7 + 1 |
Turn Door Chimes ON/OFF |
| # + 7 + 2 |
Turn Energy Saver ON/OFF |
| # + 7 + 6 |
Check Alarm Memory |
| * * * * * * |
Sends Police Panic |
|
| Pager Signals |
Pagers sends Event Code + User or Sensor Number + Last 4-Digits of Account
Example: If Account 1234 is Disarmed by Master Code pager sends 111 678 1234
| Event Codes |
| 000 |
= System Event Code (Test?) |
| 009 |
= Zone Restore |
| 001 to 024 |
= Sensor 01 to 24 Alarm or Trouble |
| 111 |
= System has been Disarmed |
| 118 |
= System Trouble has Restored |
| 119 |
= Alarm Cancelled |
| 222 |
= System was Armed to Level 2 (Stay) |
| 333 |
= System was Armed to Level 3 (Away) |
| 555 |
= System sent Phone Test |
| 888 |
= System has a Trouble |
| 999 |
= System is in Alarm |
|
| Sensor/Users |
| 601 to 659 |
= Regular User Codes 01 to 59 |
| 661 |
= Partition 1 Master Code |
| 662 |
= Partition 2 Master Code |
| 670 |
= Duress Code Partition 1 |
| 671 |
= Duress Code Partition 2 |
| 678 |
= System Master Code |
| 679 |
= Installer Code |
| 680 |
= Dealer Code |
| 681 |
= AVM 2-Way Module Used (?) |
| 697 |
= System was Quick Armed |
| 698 |
= Keyswitch Arming Number |
| 699 |
= System Armed itself after Service or Power-up |
| 128 |
= Keyfob Number |
| 129 to 204 |
= Differentiating Fobs (No idea what this is) |
| 205 to 213 |
= Keypad alarms |
|
|
