Phone Number |
Up to 18 digits |
Phone Format |
ITI Format |
(BYPASS or STAY to toggle) |
Siren Time Out |
Enter 06 |
(01 to 15) minutes) |
Duress Code |
Enter 99 |
(Duress = 1st 2-digits of code + 99) |
Account Number |
Enter last 5 digits of Account |
(no letters) |
Entry Delay 1 |
Enter 2-digits in seconds |
(08 to 88 seconds) |
Entry Delay 2 |
Enter 2-digits in minutes |
(1 to 8 minutes) |
Exit Delay |
2-digit Exit Delay |
(08 to 88 seconds) |
Activity Timeout |
Normally do not program |
(01 to 24 hours) |
House Code |
Normally do not program |
(001 to 254) |
Freeze Temp |
Normally do not program |
(40 to 90 degrees) |
Loop IS Nc |
Normally do not program |
(Sets Keypad Zone NO or NC) |
Unit Number |
Normally do not program |
Touchpad Quiet |
Quiets Keypad Beeps |
(COMMAND toggles Yes/No) |
Chime Display |
Normally do not program |
(COMMAND toggles Yes/No) |
Send Test |
Normally do not program |
(Sends Zone Text to other keypads) |
Load Test |
Normally do not program |
(I have no idea what this does) |
Delete Text |
Normally do not program |
Program Sensor |
Text Normally do not program |
(See bottom of this page) |
Learn Sensors |
1. Press COMMAND to enter (Display shows “Learn Group _ _”)
2. Enter Group number (01-29, 32) then COMMAND again
Click HERE for complete list of Sensor Types
3. Display shows LEARN Sn01, to learn different Sensor press 01 to 32
4. If this is correct sensor press COMMAND, display reads “TRIP sn”
5. Trip tamper on sensor, speaker will say “SENSOR ONE OKAY, SENSOR TWO”
6. Learn another sensor within this group or FIRE to exit to “LEARN GROUP”
7. Press FIRE again to exit back to “LEARN SENSORS” display
|
Delete Sensors |
1. Press COMMAND to enter |
(Display shows “DELETE SnXX”) |
|
2. Enter sensor to delete (01-29, 32) |
|
3. Press COMMAND |
(Display shows “DEL SnXX OK”) |
|
4. Press FIRE again to exit back to “DELETE SENSORS” display |
|
Click HERE for complete list of Sensor Types |
Upper Sensors |
Normally do not program |
|
1. Press COMMAND to enter |
|
2. Press STATUS/BYPASS to move UP/DOWN Sensor numbers |
|
Press COMMAND to toggle ON/OFF
Upper Sensor Numbers |
77 = Touchpad Tamper |
78 = Freeze Sensor |
79 = No Activity |
80 = Keypad Fire |
81 = Keypad Police |
82 = Keypad Medical/Aux |
83 = Phone Test |
84 = Enable/Disable Openings |
85 = Enable/Disable Closings |
86 = Duress Alarm |
87 = Force Arming |
88 = Energy Saver Enable |
89 = RF Touchpad Supervisory or Low Battery |
90 = AC Power Failure |
91 = Low Panel Battery |
92 = Panel Tamper |
93 = Auto Phone Test |
94 = Wireless Receiver Failure |
95 = CPU Back in Service (AC Restoral) |
96 = Phone Failure |
|
Learn Touchpad |
1. Press COMMAND to enter |
(Display shows “Press TO01 BYP”) |
2. Press BYPASS on touchpad |
(Display shows “Press TP02 BYP”) |
3. Program next Touchpad or FIRE to exit to “LEARN TOUCHPAD” display
(Anytime this section is entered all existing learned touchpads are erased)
|
|