Bosch Radionics 9412GV4 Program

***IMPORTANT WARNING***

On the 9712GV4, you MUST assign point indexes to onboard zones 1-8, even if the point indexes are not being used.

If not, a trouble will show ‘Extra Point on zone 1, Extra Point on Zone 2 etc.’

Programming Info

	Programming done only by downloading, 5200 Programmer or 5100 “Wand” Programmer
	Plug programmer in and momentarily short Reset Pin to Terminal 27 to enable program mode
	If C1 to C6 use Modem II Format with 4-digit Account, if Virtual Receiver, use BFSK with 3-digit Account
	Command 43 will cause Panel to answer downloader call (if Command 43 is enabled)

How to use a 5200 programmer

		Press the ‘ON’ button
		Enter the password (or just press ‘Enter’) on the keyboard
		Screen should say ‘Product Handlers’ and give a list of which product handlers the 5200 has loaded
		Scroll through the different handlers using the up and down arrows
		*NOTE* The technician might not have the proper handler loaded on their 5200
		When you found the right one, press the ‘ENTER GROUP’ button
		Scroll down to the panel you would like, and then press the ‘ENTER GROUP’ button again
		You’ll now be in a menu that looks identical to what you would see in RPS
		Use the up and down arrows to scroll, and the ‘ENTER GROUP’ button to enter a submenu
		To back up one level, press the ‘EXIT GROUP’ button
		To exit programming, press the ‘EXIT GROUP’ button multiple times until you are back at the password screen
		The 5200 will power off on its own over a matter of few minutes
&nbsp

9412GV4 Compliance Verification

COMPLIANCE VERIFICATION	&nbsp	Entry
SIA CP-01 Verification	–	No

PANEL WIDE PARAMETERS

Phone and Phone Parameters

		PHONE and PHONE PARAMETERS		Entry		Options
		Phone1	–	D9D18881234567		&nbsp
&nbsp	&nbsp	Phone1Format	–	ModemIlla2	–	ContactID/ModemIlla2
		Phone2	–	D9D18881234567
		Phone2Format	–	ModemIlla2	–	ContactID/ModemIlla2
		Phone3	–	D9D18881234567
		Phone3Format	–	ModemIlla2	–	ContactID/ModemIlla2
		Phone4	–	D9D18881234567
		Phone4Format	–	ModemIlla2	–	ContactID/ModemIlla2
		Point/UserFlag	–	No	–	Yes/No
		DTMFDialing	–	Yes	–	Yes/No
		PhoneSupervisionTime	–	10	–	0-240
		AlarmOnFail	–	No	–	Yes/No
		BuzzOnFail	–	No	–	Yes/No
		TwoPhoneLines	–	Yes	–	Yes/No
		ExpandTestreport	–	Yes	–	Yes/No

Report Routing

Fire Reports

FIRE REPORTS	Route Group 1	Route Group 2	Route Group 3	Route Group 4	Options
Fire Alarm	Yes	Yes	Yes	Yes	Yes/No
Fire Restoral (After Alarm)	Yes	Yes	Yes	Yes	Yes/No
Fire Missing	Yes	Yes	Yes	Yes	Yes/No
Fire trouble	Yes	Yes	Yes	Yes	Yes/No
Fire Supervision	Yes	Yes	Yes	Yes	Yes/No
Fire Restoral (After trouble)	Yes	Yes	Yes	Yes	Yes/No
Fire Cancel	Yes	Yes	Yes	Yes	Yes/No
Fire Supervision Mission	Yes	Yes	Yes	Yes	Yes/No
Fire Supervision Restoral	Yes	Yes	Yes	Yes	Yes/No

Burglar Reports

BURGLAR REPORTS	Route Group 1	Route Group 2	Route Group 3	Route Group 4	Options
Alarm Report	Yes	Yes	Yes	Yes	Yes/No
Burg Restoral (After Restoral)	Yes	Yes	Yes	Yes	Yes/No
Duress	Yes	Yes	Yes	Yes	Yes/No
Missing Alarm	Yes	Yes	Yes	Yes	Yes/No
User Code Tamper	Yes	Yes	Yes	Yes	Yes/No
trouble Report	Yes	Yes	Yes	Yes	Yes/No
Missing trouble	Yes	Yes	Yes	Yes	Yes/No
Non-Fire Supervision	Yes	Yes	Yes	Yes	Yes/No
Point Bus Fail	Yes	Yes	Yes	Yes	Yes/No
Point Bus Restoral	Yes	Yes	Yes	Yes	Yes/No
Non-Fire Cancel	Yes	Yes	Yes	Yes	Yes/No
Alarm Restore	Yes	Yes	Yes	Yes	Yes/No
Supervision Missing	Yes	Yes	Yes	Yes	Yes/No
Unverified Event	Yes	Yes	Yes	Yes	Yes/No

User Reports

USER REPORTS	Route Group 1	Route Group 2	Route Group 3	Route Group 4	Options
Point/Command Bypass	Yes	Yes	Yes	Yes	Yes/No
Forced Point	Yes	Yes	Yes	Yes	Yes/No
Point Opening	Yes	Yes	Yes	Yes	Yes/No
Point Closing	Yes	Yes	Yes	Yes	Yes/No
Was Force Armed	Yes	Yes	Yes	Yes	Yes/No
Fail To Open	Yes	Yes	Yes	Yes	Yes/No
Fail to Close	Yes	Yes	Yes	Yes	Yes/No
Extend Close Time	Yes	Yes	Yes	Yes	Yes/No
Opening Report	Yes	Yes	Yes	Yes	Yes/No
Forced Close	Yes	No	No	No	Yes/No
Closing	Yes	No	No	No	Yes/No
Forced Close Perim Instant	Yes	No	No	No	Yes/No
Force Close Perim Instant	Yes	No	No	No	Yes/No
Perimeter Instant Armed	Yes	No	No	No	Yes/No
Perimeter Delay Armed	Yes	No	No	No	Yes/No
Send User Text	Yes	Yes	Yes	Yes	Yes/No

Test Reports

TEST REPORTS	Route Group 1	Route Group 2	Route Group 3	Route Group 4	Options
S: Alarm	Yes	Yes	Yes	Yes	Yes/No
S: trouble	Yes	Yes	Yes	Yes	Yes/No
S: Supervision	Yes	Yes	Yes	Yes	Yes/No
Status Report	Yes	Yes	Yes	Yes	Yes/No
S: Open	Yes	Yes	Yes	Yes	Yes/No
S: Close	Yes	Yes	Yes	Yes	Yes/No
Test Report	Yes	Yes	Yes	Yes	Yes/No
S: Perimeter Instant	Yes	Yes	Yes	Yes	Yes/No
S: Perimeter Delay	Yes	Yes	Yes	Yes	Yes/No
S: Fire Supervision	Yes	Yes	Yes	Yes	Yes/No
S: Fire Alarm	Yes	Yes	Yes	Yes	Yes/No
S: Fire trouble	Yes	Yes	Yes	Yes	Yes/No
S: Missing Fire (trouble)	Yes	Yes	Yes	Yes	Yes/No
S: Missing Burlgary (trouble)	Yes	Yes	Yes	Yes	Yes/No
S: Missing Burlgary (Alarm)	Yes	Yes	Yes	Yes	Yes/No
S: Fire Supv Missing	Yes	Yes	Yes	Yes	Yes/No
S: Burglary Supv Missing	Yes	Yes	Yes	Yes	Yes/No
S: Door Left Open	Yes	Yes	Yes	Yes	Yes/No

Diagnostic Reports

DIAGNOSTIC REPORTS	Route Group 1	Route Group 2	Route Group 3	Route Group 4	Options
SDI Device Failure	Yes	Yes	Yes	Yes	Yes/No
SDI Device Restoral	Yes	Yes	Yes	Yes	Yes/No
Watchdog Reset	Yes	Yes	Yes	Yes	Yes/No
Parameter Checksum Fail	Yes	Yes	Yes	Yes	Yes/No
Reboot	Yes	Yes	Yes	Yes	Yes/No
Phone Line Fail	Yes	Yes	Yes	Yes	Yes/No
Phone Line Restoral	Yes	Yes	Yes	Yes	Yes/No
AC Failure	Yes	Yes	Yes	Yes	Yes/No
AC Restoral	Yes	Yes	Yes	Yes	Yes/No
Battery Missing	Yes	Yes	Yes	Yes	Yes/No
Battery Low	Yes	Yes	Yes	Yes	Yes/No
Battery Restoral	Yes	Yes	Yes	Yes	Yes/No
Route Comm Fail	Yes	Yes	Yes	Yes	Yes/No
Checksum Fail	Yes	Yes	Yes	Yes	Yes/No
Network Fail	Yes	Yes	Yes	Yes	Yes/No
Network Restoral	Yes	Yes	Yes	Yes	Yes/No
Network Condition	Yes	Yes	Yes	Yes	Yes/No
RF Interference	Yes	Yes	Yes	Yes	Yes/No
RF Interference Restore	Yes	Yes	Yes	Yes	Yes/No
Equipment Fail	Yes	Yes	Yes	Yes	Yes/No
Equipment Fail Restore	Yes	Yes	Yes	Yes	Yes/No

Relay Reports

RELAY REPORTS	Route Group 1	Route Group 2	Route Group 3	Route Group 4	Options
Sensor Reset	Yes	Yes	Yes	Yes	Yes/No
Relay Set	Yes	Yes	Yes	Yes	Yes/No
Relay Reset	Yes	Yes	Yes	Yes	Yes/No

Auto Function Reports

AUTO FUNCTION REPORTS	Route Group 1	Route Group 2	Route Group 3	Route Group 4	Options
Sked Executed	Yes	Yes	Yes	Yes	Yes/No
Sked Changed	Yes	Yes	Yes	Yes	Yes/No
Fail to Execute	Yes	Yes	Yes	Yes	Yes/No

RPS Reports

RPS REPORTS	Route Group 1	Route Group 2	Route Group 3	Route Group 4	Options
Event Log Threshold	Yes	Yes	Yes	Yes	Yes/No
Event Log Overflow	Yes	Yes	Yes	Yes	Yes/No
Parameters Changed	Yes	Yes	Yes	Yes	Yes/No
RPS Access OK	Yes	Yes	Yes	Yes	Yes/No
RPS Access Fail	Yes	Yes	Yes	Yes	Yes/No
Remote Reset	Yes	Yes	Yes	Yes	Yes/No
Program Access OK	Yes	Yes	Yes	Yes	Yes/No
Program Access Fail	Yes	Yes	Yes	Yes	Yes/No

Point Reports

POINT REPORTS	Route Group 1	Route Group 2	Route Group 3	Route Group 4	Options
Service Start	Yes	Yes	Yes	Yes	Yes/No
Service End	Yes	Yes	Yes	Yes	Yes/No
Fire Walk Start	Yes	Yes	Yes	Yes	Yes/No
Fire Walk End	Yes	Yes	Yes	Yes	Yes/No
Walk Test Start	Yes	Yes	Yes	Yes	Yes/No
Walk Test End	Yes	Yes	Yes	Yes	Yes/No
Extra Point	Yes	Yes	Yes	Yes	Yes/No
Send Point Text	Yes	Yes	Yes	Yes	Yes/No
RF Low Battery	Yes	Yes	Yes	Yes	Yes/No
RF Battery Restore	Yes	Yes	Yes	Yes	Yes/No
Service Bypass	Yes	Yes	Yes	Yes	Yes/No
Service Bypass Restore	Yes	Yes	Yes	Yes	Yes/No

User Change Reports

USER CHANGE REPORTS	Route Group 1	Route Group 2	Route Group 3	Route Group 4	Options
Date Changed	Yes	Yes	Yes	Yes	Yes/No
Time Changed	Yes	Yes	Yes	Yes	Yes/No
Delete User	Yes	Yes	Yes	Yes	Yes/No
User Code Change	Yes	Yes	Yes	Yes	Yes/No
Area Watch	Yes	Yes	Yes	Yes	Yes/No
Card/key Fob Assigned	Yes	Yes	Yes	Yes	Yes/No
Key Fob Removed	Yes	Yes	Yes	Yes	Yes/No
Change Level	Yes	Yes	Yes	Yes	Yes/No

Access Reports

ACCESS REPORTS	Route Group 1	Route Group 2	Route Group 3	Route Group 4	Options
Access Granted	Yes	Yes	Yes	Yes	Yes/No
No Entry	Yes	Yes	Yes	Yes	Yes/No
Door Left Open	Yes	Yes	Yes	Yes	Yes/No
Cycle Door	Yes	Yes	Yes	Yes	Yes/No
Door Unlocked	Yes	Yes	Yes	Yes	Yes/No
Door Secure	Yes	Yes	Yes	Yes	Yes/No
Door Request	Yes	Yes	Yes	Yes	Yes/No
Door Locked	Yes	Yes	Yes	Yes	Yes/No

Communicator

Communicator	Route Group 1	Route Group 2	Route Group 3	Route Group 4	Options
Primary Path Device	Yes	Yes	Yes	Yes	No Device
Backup Path Device	Yes	Yes	Yes	Yes	Phone 1
RF Same Network Receiver	Yes	Yes	Yes	Yes	Phone 2
					Phone 3
					Phone 4
					SDI Address 88 Path 1
					SDI Address 88 Path 2
					SDI Address 88 Path 3
					SDI Address 88 Path 4
					SDI Address 92 Path 1
					SDI Address 92 Path 2
					SDI Address 92 Path 3
					SDI Address 92 Path 4
					SDI Address 1 Path 1
					SDI Address 1 Path 2
					SDI Address 1 Path 3
					SDI Address 1 Path 4
					SDI Address 2 Path 1
					SDI Address 2 Path 2
					SDI Address 2 Path 3
					SDI Address 2 Path 4

Enhanced Communication

ENHANCED COMMUNICATION	Route Group 1	Route Group 2	Route Group 3	Route Group 4	Options
	Yes	Yes	Yes	Yes	Yes/No
	Yes	Yes	Yes	Yes	Yes/No
	Yes	Yes	Yes	Yes	Yes/No
	Yes	Yes	Yes	Yes	Yes/No
	Yes	Yes	Yes	Yes	Yes/No
	Yes	Yes	Yes	Yes	Yes/No
	Yes	Yes	Yes	Yes	Yes/No
	Yes	Yes	Yes	Yes	Yes/No

SDI RPS/Enhanced Comm

			SDI RPS/ENHANCED COMM	Entry
			Enable Enhanced Communication?	No
			Answer RPS Over Network?	Yes
			RPS Address Verification	No
			RPS Network Address
			RPS Port Number	7750

Power Supervision

POWER SUPERVISION	Entry	Options
AC Fail Time	00:00	EMPTY
Resend AC Fail	No Report	EMPTY
AC Fail Display	60	EMPTY
AC Fail/Restoral Report	Yes	Yes/No
AC Tag Along	No	Yes/No
AC/Battery Buzz	No	Yes/No
Battery Fail/Restoral Report	Yes	Yes/No

AREA WIDE PARAMETERS

Area/Bell Parameters, Open/Close Options

Area 1-8

AREA 1-8	Area 1	Area 2	Area 3	Area 4	Area 5	Area 6	Area 7	Area 8
Area On	Yes	Yes	Yes	No	No	No	No	No
Account Number	9999	9999	9999	0000	0000	0000	0000	0000
Force Arm / Bypass Max	2	2	2	2	2	2	2	2
Delay Restorals	No	No	No	No	No	No	No	No
Exit Tone	Yes	Yes	Yes	Yes	Yes	Yes	Yes	Yes
Exit Delay Time	60	60	60	60	60	60	60	60
Auto Watch	No	No	No	No	No	No	No	No
Verify Time	60	60	60	60	60	60	60	60
Duress Enable	No	No	No	No	No	No	No	No
Area Type	Regular	Regular	Regular	Regular	Regular	Regular	Regular
Two Man Rule?	No	No	No	No	No	No	No	No
Early Ambush?	No	No	No	No	No	No	No	No
Fire Time	6	6	6	6	6	6	6	6
Fire Pattern	Pulsed	Pulsed	Pulsed	Pulsed	Pulsed	Pulsed	Pulsed	Pulsed
Burg Time	6	6	6	6	6	6	6	6
Burg Pattern	Steady	Steady	Steady	Steady	Steady	Steady	Steady	Steady
Single Ring	No	No	No	No	No	No	No	No
Bell Test	No	No	No	No	No	No	No	No
Account O/C	No	No	No	No	No	No	No	No
Area O/C	Yes	Yes	Yes	Yes	Yes	Yes	Yes	Yes
Disable O/C in Window	No	No	No	No	No	No	No	No
Auto Close	No	No	No	No	No	No	No	No
Fail to Open	No	No	No	No	No	No	No	No
Fail to Close	No	No	No	No	No	No	No	No

Area 9-16

AREA 9-16	Area 9	Area 10	Area 11	Area 12	Area 13	Area 14	Area 15	Area 16
Area On	No	No	No	No	No	No	No	No
Account Number	9999	9999	9999	0000	0000	0000	0000	0000
Force Arm / Bypass Max	2	2	2	2	2	2	2	2
Delay Restorals	No	No	No	No	No	No	No	No
Exit Tone	Yes	Yes	Yes	Yes	Yes	Yes	Yes	Yes
Exit Delay Time	60	60	60	60	60	60	60	60
Auto Watch	No	No	No	No	No	No	No	No
Verify Time	60	60	60	60	60	60	60	60
Duress Enable	No	No	No	No	No	No	No	No
Area Type	Regular	Regular	Regular	Regular	Regular	Regular	Regular
Two Man Rule?	No	No	No	No	No	No	No	No
Early Ambush?	No	No	No	No	No	No	No	No
Fire Time	6	6	6	6	6	6	6	6
Fire Pattern	Pulsed	Pulsed	Pulsed	Pulsed	Pulsed	Pulsed	Pulsed	Pulsed
Burg Time	6	6	6	6	6	6	6	6
Burg Pattern	Steady	Steady	Steady	Steady	Steady	Steady	Steady	Steady
Single Ring	No	No	No	No	No	No	No	No
Bell Test	No	No	No	No	No	No	No	No
Account O/C	No	No	No	No	No	No	No	No
Area O/C	Yes	Yes	Yes	Yes	Yes	Yes	Yes	Yes
Disable O/C in Window	No	No	No	No	No	No	No	No
Auto Close	No	No	No	No	No	No	No	No
Fail to Open	No	No	No	No	No	No	No	No
Fail to Close	No	No	No	No	No	No	No	No

Area 17-24

AREA 17-24	Area 17	Area 18	Area 19	Area 20	Area 21	Area 22	Area 23	Area 24
Area On	No	No	No	No	No	No	No	No
Account Number	9999	9999	9999	0000	0000	0000	0000	0000
Force Arm / Bypass Max	2	2	2	2	2	2	2	2
Delay Restorals	No	No	No	No	No	No	No	No
Exit Tone	Yes	Yes	Yes	Yes	Yes	Yes	Yes	Yes
Exit Delay Time	60	60	60	60	60	60	60	60
Auto Watch	No	No	No	No	No	No	No	No
Verify Time	60	60	60	60	60	60	60	60
Duress Enable	No	No	No	No	No	No	No	No
Area Type	Regular	Regular	Regular	Regular	Regular	Regular	Regular
Two Man Rule?	No	No	No	No	No	No	No	No
Early Ambush?	No	No	No	No	No	No	No	No
Fire Time	6	6	6	6	6	6	6	6
Fire Pattern	Pulsed	Pulsed	Pulsed	Pulsed	Pulsed	Pulsed	Pulsed	Pulsed
Burg Time	6	6	6	6	6	6	6	6
Burg Pattern	Steady	Steady	Steady	Steady	Steady	Steady	Steady	Steady
Single Ring	No	No	No	No	No	No	No	No
Bell Test	No	No	No	No	No	No	No	No
Account O/C	No	No	No	No	No	No	No	No
Area O/C	Yes	Yes	Yes	Yes	Yes	Yes	Yes	Yes
Disable O/C in Window	No	No	No	No	No	No	No	No
Auto Close	No	No	No	No	No	No	No	No
Fail to Open	No	No	No	No	No	No	No	No
Fail to Close	No	No	No	No	No	No	No	No

Area 25-32

AREA 25-32	Area 25	Area 26	Area 27	Area 28	Area 29	Area 30	Area 31	Area 32
Area On	No	No	No	No	No	No	No	No
Account Number	9999	9999	9999	0000	0000	0000	0000	0000
Force Arm / Bypass Max	2	2	2	2	2	2	2	2
Delay Restorals	No	No	No	No	No	No	No	No
Exit Tone	Yes	Yes	Yes	Yes	Yes	Yes	Yes	Yes
Exit Delay Time	60	60	60	60	60	60	60	60
Auto Watch	No	No	No	No	No	No	No	No
Verify Time	60	60	60	60	60	60	60	60
Duress Enable	No	No	No	No	No	No	No	No
Area Type	Regular	Regular	Regular	Regular	Regular	Regular	Regular
Two Man Rule?	No	No	No	No	No	No	No	No
Early Ambush?	No	No	No	No	No	No	No	No
Fire Time	6	6	6	6	6	6	6	6
Fire Pattern	Pulsed	Pulsed	Pulsed	Pulsed	Pulsed	Pulsed	Pulsed	Pulsed
Burg Time	6	6	6	6	6	6	6	6
Burg Pattern	Steady	Steady	Steady	Steady	Steady	Steady	Steady	Steady
Single Ring	No	No	No	No	No	No	No	No
Bell Test	No	No	No	No	No	No	No	No
Account O/C	No	No	No	No	No	No	No	No
Area O/C	Yes	Yes	Yes	Yes	Yes	Yes	Yes	Yes
Disable O/C in Window	No	No	No	No	No	No	No	No
Auto Close	No	No	No	No	No	No	No	No
Fail to Open	No	No	No	No	No	No	No	No
Fail to Close	No	No	No	No	No	No	No	No

Area Descriptions (Reference Only)

		AREA DESCRIPTIONS	Area Description
		Area 1	Area 1
		Area 2	Area 2
		Area 3	Area 3
		Area 4	Area 4
		Area 5	Area 5
		Area 6	Area 6
		Area 7	Area 7
		Area 8	Area 8
		Area 9	Area 9
		Area 10	Area 10
		Area 11	Area 11
		Area 11	Area 11
		Area 12	Area 12
		Area 13	Area 13
		Area 14	Area 14
		Area 15	Area 15
		Area 16	Area 16
		Area 17	Area 17
		Area 18	Area 18
		Area 19	Area 19
		Area 20	Area 20
		Area 21	Area 21
		Area 22	Area 22
		Area 23	Area 23
		Area 24	Area 24
		Area 25	Area 25
		Area 26	Area 26
		Area 27	Area 27
		Area 28	Area 28
		Area 29	Area 29
		Area 30	Area 30
		Area 31	Area 31
		Area 32	Area 32

COMMAND CENTER

COMMAND CENTER ASSIGNMENTS 1-4

CMD Ctr ASSIGNMENTS		CC Address 1	CC Address 2	CC Address 3	CC Address 4
Supervision	–	No	No	No	No
Enhanced Command Center	–	No	Yes	No	No
Area Assignment	–	2	3	1	1
Scope	–	Area Wide	Panel Wide	No Keypad	No Keypad
Area(s) in Scope	–	2	All	None	None
Passcode Follows Scope	–	Yes	Yes	Yes	Yes
Enter Key Relay	–	0	0	0	0
Passcode Enter Function	–	Arm/Disarm	Arm/Disarm	Arm/Disarm	Arm/Disarm
Dual Authentication	–	No	No	No	No
Dual Authentication Duration	–	10 Seconds	10 Seconds	10 Seconds	10 Seconds
Assign Door	–	Door 1	No Door	No Door	No Door
trouble Tone	–	Yes	Yes	Yes	Yes
Entry Tone	–	Yes	Yes	Yes	Yes
Exit Tone	–	Yes	Yes	Yes	Yes
Arm Area Warning Tone	–	Yes	Yes	Yes	Yes
Close Door Warning Tone	–	Yes	Yes	Yes	Yes
Idle Scroll Lock	–	No	No	No	No
Menu Key Lock	–	No	No	No	No
Abort Display	–	Yes	Yes	Yes	Yes
Cancel Display	–	Yes	Yes	Yes	Yes

COMMAND CENTER ASSIGNMENTS 5-8

CMD Ctr ASSIGNMENTS		CC Address 5	CC Address 6	CC Address 7	CC Address 8
Supervision	–	No	No	No	Yes
Enhanced Command Center	–	No	No	No	No
Area Assignment	–	2	3	1	1
Scope	–	Area Wide	Panel Wide	No Keypad	Panel Wide
Area(s) in Scope	–	2	All	None	None
Passcode Follows Scope	–	Yes	Yes	Yes	Yes
Enter Key Relay	–	0	0	0	0
Passcode Enter Function	–	Arm/Disarm	Arm/Disarm	Arm/Disarm	Arm/Disarm
Dual Authentication	–	No	No	No	No
Dual Authentication Duration	–	10 Seconds	10 Seconds	10 Seconds	10 Seconds
Assign Door	–	Door 1	No Door	No Door	No Door
trouble Tone	–	Yes	Yes	Yes	Yes
Entry Tone	–	Yes	Yes	Yes	Yes
Exit Tone	–	Yes	Yes	Yes	Yes
Arm Area Warning Tone	–	Yes	Yes	Yes	Yes
Close Door Warning Tone	–	Yes	Yes	Yes	Yes
Idle Scroll Lock	–	No	No	No	No
Menu Key Lock	–	No	No	No	No
Abort Display	–	Yes	Yes	Yes	Yes
Cancel Display	–	Yes	Yes	Yes	Yes

COMMAND CENTER ASSIGNMENTS
9-16 ARE ALL THE SAME

CMD Ctr ASSIGNMENTS		CC Address 9	CC Address 10	CC Address 11	CC Address 12
Supervision	–	No	No	No	No
Enhanced Command Center	–	No	No	No	No
Area Assignment	–	2	3	1	1
Scope	–	Area Wide	Panel Wide	No Keypad	No Keypad
Area(s) in Scope	–	2	All	None	None
Passcode Follows Scope	–	Yes	Yes	Yes	Yes
Enter Key Relay	–	0	0	0	0
Passcode Enter Function	–	Arm/Disarm	Arm/Disarm	Arm/Disarm	Arm/Disarm
Dual Authentication	–	No	No	No	No
Dual Authentication Duration	–	10 Seconds	10 Seconds	10 Seconds	10 Seconds
Assign Door	–	Door 1	No Door	No Door	No Door
trouble Tone	–	Yes	Yes	Yes	Yes
Entry Tone	–	Yes	Yes	Yes	Yes
Exit Tone	–	Yes	Yes	Yes	Yes
Arm Area Warning Tone	–	Yes	Yes	Yes	Yes
Close Door Warning Tone	–	Yes	Yes	Yes	Yes
Idle Scroll Lock	–	No	No	No	No
Menu Key Lock	–	No	No	No	No
Abort Display	–	Yes	Yes	Yes	Yes
Cancel Display	–	Yes	Yes	Yes	Yes

AREA TEXT

AREA TEXT		“Area # is On” Text	“Area # Not Ready” Text	“Area # Is Off” Text	“Area # Account Is On” Text	“Area # Name” Text
Area 1 Text	–	A1 AREA IS ON	A1 NOT READY	A1 AREA IS OFF	A1 ACCOUNT ON	A1 NAME TEXT
Area 2 Text	–	A2 AREA IS ON	A2 NOT READY	A2 AREA IS OFF	A2 ACCOUNT ON	A2 NAME TEXT
Area 3 Text	–	A3 AREA IS ON	A3 NOT READY	A3 AREA IS OFF	A3 ACCOUNT ON	A3 NAME TEXT
Area 4 Text	–	A4 AREA IS ON	A4 NOT READY	A4 AREA IS OFF	A4 ACCOUNT ON	A4 NAME TEXT
Area 5 Text	–	A5 AREA IS ON	A5 NOT READY	A5 AREA IS OFF	A5 ACCOUNT ON	A5 NAME TEXT
Area 6 Text	–	A6 AREA IS ON	A6 NOT READY	A6 AREA IS OFF	A6 ACCOUNT ON	A6 NAME TEXT
Area 7 Text	–	A7 AREA IS ON	A7 NOT READY	A7 AREA IS OFF	A7 ACCOUNT ON	A7 NAME TEXT
Area 8 Text	–	A8 AREA IS ON	A8 NOT READY	A8 AREA IS OFF	A8 ACCOUNT ON	A8 NAME TEXT
Area 9 Text	–	A9 AREA IS ON	A9 NOT READY	A9 AREA IS OFF	A9 ACCOUNT ON	A9 NAME TEXT
Area 10 Text	–	A10 AREA IS ON	A10 NOT READY	A10 AREA IS OFF	A10 ACCOUNT ON	A10 NAME TEXT
Area 11 Text	–	A11 AREA IS ON	A11 NOT READY	A11 AREA IS OFF	A11 ACCOUNT ON	A11 NAME TEXT
Area 12 Text	–	A12 AREA IS ON	A12 NOT READY	A12 AREA IS OFF	A12 ACCOUNT ON	A12 NAME TEXT
Area 13 Text	–	A13 AREA IS ON	A13 NOT READY	A13 AREA IS OFF	A13 ACCOUNT ON	A13 NAME TEXT
Area 14 Text	–	A14 AREA IS ON	A14 NOT READY	A14 AREA IS OFF	A14 ACCOUNT ON	A14 NAME TEXT
Area 15 Text	–	A15 AREA IS ON	A15 NOT READY	A15 AREA IS OFF	A15 ACCOUNT ON	A15 NAME TEXT
Area 16 Text	–	A16 AREA IS ON	A16 NOT READY	A16 AREA IS OFF	A16 ACCOUNT ON	A16 NAME TEXT
Area 17 Text	–	A17 AREA IS ON	A17 NOT READY	A17 AREA IS OFF	A17 ACCOUNT ON	A17 NAME TEXT
Area 18 Text	–	A18 AREA IS ON	A18 NOT READY	A18 AREA IS OFF	A18 ACCOUNT ON	A18 NAME TEXT
Area 19 Text	–	A19 AREA IS ON	A19 NOT READY	A19 AREA IS OFF	A19 ACCOUNT ON	A19 NAME TEXT
Area 20 Text	–	A20 AREA IS ON	A20 NOT READY	A20 AREA IS OFF	A20 ACCOUNT ON	A20 NAME TEXT

USER INTERFACE

Command Center Functions

COMMAND CENTER FUNCTIONS		Entry	Options
(2) Master Arm Delay – Command 1	–	P	– E P
(3) Master Arm Instant	–	–
(4) Perimeter Instant – Command 2	–	–
(5) Perimeter Delay – Command 3	–	P
(6) Watch Mode – Command 6	–	E
(7) Perimeter Partial – Command 8	–	P
(8) View Area Status	–	P
(9) View Memory – Command 40	–	E
(10) View Point Status	–	E
(11) Walk Test – Command 44	–	E
(12) Fire Test – Command 58	–	P
(13) Send Report – Command 41/42	–	E
(14)Door Control – Command 46	–	P
(37) Access Control Level	–	P
(15) Change Display – Command 49	–	E
(16) Change Time/Date – Command 45	–	P
(17) Change Passcode – Command 55	–	P
(18) Add User – Command 56	–	P
(19) Delete User – Command 53	–	P
(20) Extend Close – Command 51	–	P
(21) View Log – (Use 99 + Enter key)	–	E
(22) Print Log – (Use 99 + Enter key)	–	P
(23) User Command 7	–	–
(24) User Command 9	–	–
(25) Bypass a Point – Command 0	–	P
(26) Unbypass a Point – Command 00	–	P
(27) Reset Sensors – Command 47	–	E
(28) Change Relays – Command 54	–	P
(29) Remote Program – Command 43	–	P
(30) Mote To Area – Command 50	–	P
(32) Display Revision – Command 59	–	E
(33) Service Walk – (Use 99 + Enter key)	–	P
(34) Default Text – Command 57	–	P
(35) Change Skeds – Command 52	–	P
(36) Invisible Walk	–	P
(128) Custom Function 128	–	E
(129) Custom Function 129	–	E
(130) Custom Function 130	–	E
(131) Custom Function 131	–	E
(132) Custom Function 132	–	P
(133) Custom Function 133	–	P
(134) Custom Function 134	–	P
(135) Custom Function 135	–	P
(136) Custom Function 136	–	P
(137) Custom Function 137	–	P
(138) Custom Function 138	–	P
(139) Custom Function 139	–	P
(140) Custom Function 110	–	P
(141) Custom Function 141	–	P
(142) Custom Function 142	–	P
(143) Custom Function 143	–	P
Keypad Programming	–	P

FUNCTION LIST

FUNCTION LIST		Function #	Set/Clear all CC	CC Address 1	CC Address 2
Menu Item 1	–	128	Set/Clear all CC	Yes	Yes
Menu Item 2	–	129	Set/Clear all CC	Yes	Yes
Menu Item 3	–	130	Set/Clear all CC	Yes	Yes
Menu Item 4	–	131	Set/Clear all CC	Yes	Yes
Menu Item 5	–	15	Set/Clear all CC	Yes	Yes
Menu Item 6	–	16	Set/Clear all CC	Yes	Yes
Menu Item 7	–	17	Set/Clear all CC	Yes	Yes
Menu Item 8	–	18	Set/Clear all CC	Yes	Yes
Menu Item 9	–	19	Set/Clear all CC	Yes	Yes
Menu Item 10	–	25	Set/Clear all CC	Yes	Yes
Menu Item 11	–	26	Set/Clear all CC	Yes	Yes
Menu Item 12	–	9	Set/Clear all CC	Yes	Yes
Menu Item 13	–	10	Set/Clear all CC	Yes	Yes
Menu Item 14	–	8	Set/Clear all CC	Yes	Yes
Menu Item 15	–	21	Set/Clear all CC	Yes	Yes
Menu Item 16	–	1	Set/Clear all CC	Yes	Yes
Menu Item 17	–	2	Set/Clear all CC	Yes	Yes
Menu Item 18	–	29	Set/Clear all CC	Yes	Yes
Menu Item 19	–	11	Set/Clear all CC	Yes	Yes
Menu Item 21-32	–	0	Set/Clear all CC	Yes	Yes

RELAY PARAMETERS

Area Wide Relays

Relay Area 1-8

Relay Area 1-8	Area 1	Area 2	Area 3	Area 4	Area 5	Area 6	Area 7	Area 8
Alarm Bell	A	A	A	A	A	A	A	A
Fire Bell	B	B	B	B	B	A	A	A
Reset Sensors	C	C	C	C	A	A	A	A
Fail To Close / Perimeter Armed	0	0	0	0	0	0	0	0
Force Armed	0	0	0	0	0	0	0	0
Watch Mode	0	0	0	0	0	0	0	0
Area Armed	0	0	0	0	0	0	0	0
Area Fault	0	0	0	0	0	0	0	0
Duress Relay	0	0	0	0	0	0	0	0
Perimeter Faults	0	0	0	0	0	0	0	0
Silent Alarm	0	0	0	0	0	0	0	0

PASSCODES

Passcodes

Users 0 – 200

Users 0 – 200	User Name	Passcode	User Group	A1 Auth.	A2 Auth.	A3 Auth.	A4 Auth.
User 0	SERVICE PASSCODE	123	0	15	15	15	15
User 1	MASTER	3238	0	1	1	1	0
User 2	TEST CODE	123456	0	1	1	1	0
User 3		0	0	0	0	0	0
User 4		0	0	0	0	0	0
User 5	0	0	0	0	0	0	0
User 6	0	0	0	0	0	0	0
User 7	0	0	0	0	0	0	0
User 8	0	0	0	0	0	0	0
User 9	0	0	0	0	0	0	0
User 10	0	0	0	0	0	0	0
.
.
.
User 200	0	0	0	0	0	0	0

Users 201 – 400

Users 201 – 400	User Name	Passcode	User Group	A1 Auth.	A2 Auth.	A3 Auth.	A4 Auth.
User 201	0	0	0	0	0	0	0
User 202	0	0	0	0	0	0	0
User 203	0	0	0	0	0	0	0
User 204	0	0	0	0	0	0	0
User 205	0	0	0	0	0	0	0
User 206	0	0	0	0	0	0	0
User 207	0	0	0	0	0	0	0
User 208	0	0	0	0	0	0	0
User 209	0	0	0	0	0	0	0
User 210	0	0	0	0	0	0	0
User 211	0	0	0	0	0	0	0
.
.
.
User 400	0	0	0	0	0	0	0

Users 401 – 600

Users 401 – 600	User Name	Passcode	User Group	A1 Auth.	A2 Auth.	A3 Auth.	A4 Auth.
User 401	0	0	0	0	0	0	0
User 402	0	0	0	0	0	0	0
User 403	0	0	0	0	0	0	0
User 404	0	0	0	0	0	0	0
User 405	0	0	0	0	0	0	0
User 406	0	0	0	0	0	0	0
User 407	0	0	0	0	0	0	0
User 408	0	0	0	0	0	0	0
User 409	0	0	0	0	0	0	0
User 410	0	0	0	0	0	0	0
User 411	0	0	0	0	0	0	0
.
.
.
User 600	0	0	0	0	0	0	0

Users 601 – 800

Users 601 – 600	User Name	Passcode	User Group	A1 Auth.	A2 Auth.	A3 Auth.	A4 Auth.
User 601	0	0	0	0	0	0	0
User 602	0	0	0	0	0	0	0
User 603	0	0	0	0	0	0	0
User 604	0	0	0	0	0	0	0
User 605	0	0	0	0	0	0	0
User 606	0	0	0	0	0	0	0
User 607	0	0	0	0	0	0	0
User 608	0	0	0	0	0	0	0
User 609	0	0	0	0	0	0	0
User 610	0	0	0	0	0	0	0
User 611	0	0	0	0	0	0	0
.
.
.
User 800	0	0	0	0	0	0	0

Users 801 – 999

Users 801 – 999	User Name	Passcode	User Group	A1 Auth.	A2 Auth.	A3 Auth.	A4 Auth.
User 801	0	0	0	0	0	0	0
User 802	0	0	0	0	0	0	0
User 803	0	0	0	0	0	0	0
User 804	0	0	0	0	0	0	0
User 805	0	0	0	0	0	0	0
User 806	0	0	0	0	0	0	0
User 807	0	0	0	0	0	0	0
User 808	0	0	0	0	0	0	0
User 809	0	0	0	0	0	0	0
User 810	0	0	0	0	0	0	0
User 811	0	0	0	0	0	0	0
.
.
.
User 999	0	0	0	0	0	0	0

POINTS

Point Indexes

Point Indexes 1-16, Columns 1-8

Point Indexes 1-16

|&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp1&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp|

|&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp2&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp|

|&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp3&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp|

|&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp4&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp|

|&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp5&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp|

|&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp6&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp|

|&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp7&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp|

|&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp8&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp|

Point Type

Point Response

Entry Delay

Entry Tone Off

Silent Bell

Yes

Ring Until Restored

Audible after 2 Fails

Invisible Point

Yes

Buzz On Fault

Watch Point

Yes

Relay Response Type

Display as Device

Local While Disarmed

Local While Armed

Disable Restorals

Force Arm Returnable

Bypass Returnable

Bypassable

Swinger Bypass

Report Byp at Occurence

Defer Bypass Report

Cross Point

Fire Point

Yes

Alarm Verify

Yes

Resettable

Yes

Alarm Abort

Yes

Wireless Point Supervision Time

Point Indexes 1-16, Columns 9-16

Point Indexes 1-16

|&nbsp&nbsp&nbsp&nbsp&nbsp9&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp|

|&nbsp&nbsp&nbsp&nbsp&nbsp10&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp|

|&nbsp&nbsp&nbsp&nbsp&nbsp11&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp|

|&nbsp&nbsp&nbsp&nbsp&nbsp12&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp|

|&nbsp&nbsp&nbsp&nbsp&nbsp13&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp|

|&nbsp&nbsp&nbsp&nbsp&nbsp14&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp|

|&nbsp&nbsp&nbsp&nbsp&nbsp15&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp|

|&nbsp&nbsp&nbsp&nbsp&nbsp16&nbsp&nbsp&nbsp&nbsp&nbsp&nbsp|

Point Type

Point Response

Entry Delay

Entry Tone Off

Silent Bell

Yes

Ring Until Restored

Audible after 2 Fails

Invisible Point

Yes

Buzz On Fault

Watch Point

Yes

Relay Response Type

Display as Device

Local While Disarmed

Local While Armed

Disable Restorals

Force Arm Returnable

Bypass Returnable

Bypassable

Swinger Bypass

Report Byp at Occurence

Defer Bypass Report

Cross Point

Fire Point

Yes

Alarm Verify

Yes

Resettable

Yes

Alarm Abort

Yes

Wireless Point Supervision Time

SCHEDULES

Open/Close Windows

OPEN/CLOSE WINDOWS	Window 1	Window 2	Window 3	Window 4	Window 5	Window 6	Window 7	Window 8
Sunday	No	No	No	No	No	No	No	No
Monday	No	No	No	No	No	No	No	No
Tuesday	No	No	No	No	No	No	No	No
Wednesday	No	No	No	No	No	No	No	No
Thursday	No	No	No	No	No	No	No	No
Friday	No	No	No	No	No	No	No	No
Saturday	No	No	No	No	No	No	No	No
Open Early Begin	00:00	00:00	00:00	00:00	00:00	00:00	00:00	00:00
Open Window Start	00:00	00:00	00:00	00:00	00:00	00:00	00:00	00:00
Open Window Stop	00:00	00:00	00:00	00:00	00:00	00:00	00:00	00:00
Close Early Begin	00:00	00:00	00:00	00:00	00:00	00:00	00:00	00:00
Close Window Start	00:00	00:00	00:00	00:00	00:00	00:00	00:00	00:00
Close Window Stop	00:00	00:00	00:00	00:00	00:00	00:00	00:00	00:00
Xept on Holiday	No	No	No	No	No	No	No	No
Holiday 1	No	No	No	No	No	No	No	No
Holiday 2	No	No	No	No	No	No	No	No
Holiday 3	No	No	No	No	No	No	No	No
Holiday 4	No	No	No	No	No	No	No	No
Area 1	No	No	No	No	No	No	No	No
Area 2	No	No	No	No	No	No	No	No
Area 3	No	No	No	No	No	No	No	No
Area 4	No	No	No	No	No	No	No	No
Area 5	No	No	No	No	No	No	No	No
Area 6	No	No	No	No	No	No	No	No
Area 7	No	No	No	No	No	No	No	No
Area 8	No	No	No	No	No	No	No	No
Area 9	No	No	No	No	No	No	No	No
Area 10	No	No	No	No	No	No	No	No
Area 11	No	No	No	No	No	No	No	No
Area 12	No	No	No	No	No	No	No	No
Area 13	No	No	No	No	No	No	No	No
Area 14	No	No	No	No	No	No	No	No
Area 15	No	No	No	No	No	No	No	No
Area 16	No	No	No	No	No	No	No	No
Area 17	No	No	No	No	No	No	No	No
Area 18	No	No	No	No	No	No	No	No
Area 19	No	No	No	No	No	No	No	No
Area 20	No	No	No	No	No	No	No	No
Area 21	No	No	No	No	No	No	No	No
Area 22	No	No	No	No	No	No	No	No
Area 23	No	No	No	No	No	No	No	No
Area 24	No	No	No	No	No	No	No	No
Area 25	No	No	No	No	No	No	No	No
Area 26	No	No	No	No	No	No	No	No
Area 27	No	No	No	No	No	No	No	No
Area 28	No	No	No	No	No	No	No	No
Area 29	No	No	No	No	No	No	No	No
Area 30	No	No	No	No	No	No	No	No
Area 31	No	No	No	No	No	No	No	No
Area 32	No	No	No	No	No	No	No	No

User Group

OPEN/CLOSE WINDOWS	Window 1	Window 2	Window 3	Window 4	Window 5	Window 6	Window 7	Window 8
User Group	1	1	1	1	1	1	1	1
Sunday	No	No	No	No	No	No	No	No
Monday	No	No	No	No	No	No	No	No
Tuesday	No	No	No	No	No	No	No	No
Wednesday	No	No	No	No	No	No	No	No
Thursday	No	No	No	No	No	No	No	No
Friday	No	No	No	No	No	No	No	No
Saturday	No	No	No	No	No	No	No	No
Group Enable Time	00:00	00:00	00:00	00:00	00:00	00:00	00:00	00:00
Group Disable Time	00:00	00:00	00:00	00:00	00:00	00:00	00:00	00:00
Xept on Holiday	No	No	No	No	No	No	No	No
Holiday 1	No	No	No	No	No	No	No	No
Holiday 2	No	No	No	No	No	No	No	No
Holiday 3	No	No	No	No	No	No	No	No
Holiday 4	No	No	No	No	No	No	No	No

Skeds

Sked Descriptions (Ref. Only)

				Sked #	Sked Description
				Sked 1	Test Report
				Sked 2
				Sked 3
				Sked 4
				.
				.
				.
				Sked 40

ACCESS CONTROL

Example

AUXPARM

Example

SD12 MODULES

Example

HARDWARE SWITCH SETTINGS

Example