ATT 8300 Basics

Zones 16 Hardwire (Zones 01 to 16) 41 Wireless (Zones 81 to 122)
Resistors 1K
Batteries 12 volt rechargeable Gel-Cell inside main panel
AC Transformer looks like a Black “Brick” type
All Wireless use 9-volt Alkaline
Downloadable Yes Note: Cannot disarm through download only arm!
Panic Buttons Police & Emergency, press each pair to activate
Arming 4-digit Code + AWAY
Quick Arm (If enabled) Enter 1st Digit of Code + AWAY, HOME or STAY
Disarming 4-digit Code + OFF
Zone Status Keypad will NOT what zones are open until customer arms system
(Ready light will be ON if all zones are closed, OFF if zones are open)
Reset Alarm 1. Display Screen shows “ALARM” or “ALARM/TROUBLE”, press SELECT
2. Screen will show “REVIEW REMOVE”, REVIEW should flash, press SELECT
3. Current Alarm or Trouble will display along with “. . .” and “>>”
4. Press NEXT until “. . .” flashes then SELECT to return to “REVIEW REMOVE”
5. Press NEXT until “REVIEW” flashes and press SELECT
6. Current Alarm or Trouble will display again along with “. . .” and “OK”
7. Press NEXT until “OK” flashes and press SELECT to remove it from memory
8. Continue until Alarms/Troubles clear then press NEXT until “>>” flashes
9. Press SELECT to exit
(Troubles will not clear until problem is corrected)
Force Bypass (If enabled) Open door/window and arm system, keypad should show zone bypassed
Manual Bypass (Manually bypassed Zones will stay bypassed until manually unbypassed)
1. Press NEXT until “Security” flashes then SELECT and enter Master Code
2. “Codes” will flash, press NEXT until “Program” flashes and press SELECT
4. “Bypass” will flash, press SELECT
5. “Add” displays, press SELECT, enter zone to bypass (1 to 16 and 81 to 122) then SELECT
6. Display shows “Sensor Bypassed”
7. Press NEXT until ” < ” and SELECT to bypass more sensors or ” >> ” and SELECT to exit
Unbypass 1. Press NEXT until “Security” flashes then SELECT and enter Master Code
2. “Codes” will flash, press NEXT until “Program” flashes and press SELECT
4. “Bypass” will flash, press SELECT
5. Press NEXT until “REMOVE” displays, press SELECT
6. Enter zone to unbypass (1 to 16 and 81 to 122) then SELECT
6. Display shows “Sensor UnBypassed”
7. Press SELECT to exit
Door Chimes 1. Press NEXT
2. “Security” should be flashing, press SELECT and enter Master Code
3. “Codes” will flash, press NEXT until “Program” flashes, press SELECT
4. Press NEXT until “Chime” flashes then press SELECT
5. Press NEXT to toggle “ON” or “OFF” then press SELECT
6. Press NEXT until >> flashes and press SELECT to exit
Volume Move slider on left side of Keypad
Set Time/Date 1. Press NEXT until “Security” flashes, press SELECT
2. Enter 4-digit Master Code
3. Press NEXT until “Clock” flashes, press SELECT
4. “Time” flashes, press SELECT and enter correct Hours
5. Press SELECT and enter correct Minutes
6. Press SELECT and enter if AM or PM then SELECT
7. Press NEXT until “Date” flashes and press SELECT
8. Enter 4-digit Year + SELECT, 2-digit Month + SELECT, 2-digit Day + SELECT
9. Press NEXT until “>>” is flashing then SELECT to exit
Test System 1. Press NEXT until “Security” flashes, press SELECT
2. Enter 4-digit Master Code
3. Press NEXT until “TEST” flashes, press SELECT
4. Display will show “TEST MODE LIST SEND < >>” LIST should be flashing
5. Press SELECT, display shows “NOTHING IN LIST”, open doors/windows
6. After activating all zones last zone tested will show on display
7. Press NEXT until “. . .” flashes and press SELECT to view tested sensors
8 Press NEXT until >> displays and press SELECT to exit
Intercom 1. Press NEXT until “INTERCOM” flashes then SELECT
2. You can now speak to other keypads, others can talk by pressing SELECT
3. To finish press NEXT until “HANGUP” flashes then SELECT from either keypad

Answer
Phone Call
1. When Phone rings keypad will show “PHONE”, press SELECT to answer
2. While on phone display will show “HANGUP MUTE HOLD FLASH”
3. To finish call press NEXT until “HANGUP” flashes then SELECT
4. To mute a call press NEXT until “MUTE” flashes then SELECT
5. To place a call on Hold press NEXT until “HOLD” flashes then SELECT
6. If Call-Waiting press NEXT until “FLASH” then press SELECT for other call
Make
Phone Call
1. Press NEXT until “PHONE” flashes and press SELECT
2. Display shows “HANGUP MUTE HOLD FLASH”
3. Enter Phone Number just like standard phone
4. To finish call press NEXT until “HANGUP” flashes then SELECT
Error Messages (These may appear if user entered incorrect information)
Access Denied Wrong User Code entered or not high enough access
All Codes Used All 15 Access Codes are programmed
Bypass
Not Allowed
System is programmed not to bypass zones
Cannot
Remove Code
User Cannot remove a code that is in use
Code in Use Code entered already programmed
Code
Not Entered
System did not recognize new code being entered
Intercom
in Use
Someone at another keypad is using the Intercom
Intercom Service
Unavailable
Somone at another keypad is using Intercom
Invalid Code User tried to Add or Remove a code that is not valid
Invalid
Sensor Number
A Sensor Number was entered that does not exist
No Sensors
in List
System is in Test Modewith no alarm signals yet
Phone Service
Unavailable
Someone is using Phone or Intercom at another keypad
Priority Zone
Not Bypassed
Sensor cannot be bypassed
Programming
in Use
Someone is changing programming at another keypad
System Must
Be Off
An operation was attempted while system was armed