1. Home
  2. AT&T
  3. AT&T 8000
  4. AT&T 8000
 

ATT 8000 Program

Add Sensor Set dip switches on sensors, panel will “see” any sensor with same House Code
Delete Sensor 1. Power panel down
2. Remove sensor batteries, change House Code dip switches of sensor to delete
3. Power system up
4. Put system in test mode and test all sensors you want supervised
Downloading Have tech move LOCAL/REMOTE to LOCAL when phone is ringing to connect
Tech needs to move jumper back to REMOTE when finished to free phone line
By Programmer 1. Plug programmer into Dialer’s LOCAL PROGRAMMING pins
(Dialer will power programmer if needed)
2. Programmer will show “PROGRAMMER REVISION C”
3. Press ↓ until “LOCAL CONNECT?” shows then press ENTER
4. At “ENTER PASSCODE” prompt enter 6-digit passcode (default = 111111) then ENTER
5. At “WAITING FOR ANSWER” move Local/Remote jumper to LOCAL (this kills the phone)
6. Display will show “HANDSHAKE” then “SENDING PASSCODE” then “EDIT DATABASE?”
(if it goes back to showing “LOCAL CONNECT?” then wrong passcode was used)
7. Press ↓ until “UPLOAD DIALER?” then ENTER (optional)
8. Press Down or Up Arrow keys until “EDIT DATABASE?” shows then press ENTER
9. Begin at location 01 with cursor under use ← or → to move Left or Right within a location
10 . Press ↑ or ↓ to show all possible values in that location, save by pressing ENTER
11. Move to next location by pressing ↑ or ↓ with cursor below location digits
12. When finished press SHIFT then ENTER for “EDIT DATABASE?”
13. Press ↓ until “DOWNLOAD DIALER?” shows, press ENTER
14. If needed press ↑ or ↓ until “SAVE TO MEMORY” to save into programmer
15. When finished disconnect programmer and move LOCAL/REMOTE to REMOTE
CMD Program Data Function Options
01 I_1_I System Enable 0 = Normal, 1 = Kill (Disabled)
02 I_1_I_1_I_1_I_1_I_1_I_1_I Pass Code (Default = 111111)
03 I_2_I_5_I 1st Digit = Receiver
  Format 		1 = Slow A 2300Hz ack
2 = Fast A 2300Hz ack
3 = Slow B 1400Hz ack
4 = Fast B 1400Hz ack
5 = Sum Check 1400Hz ack
6 = Sum Check 2300Hz ack
2nd Digit = Message 1 = 3/1 Single, .5 sec delay
Format 2 = 3/1 Single, 2 sec delay
3 = 3/1 Extended, .5 sec delay
4 = 3/1 Extended, 2 sec delay
5 = 4/2
6 = 4/1
7 = 4/9 Ademco DTMF
04 I_X_I_X_I Receiver 2 Format (Not Used)
05 I_8_I_1_I_0_I_*5_I Communications Control
1st Digit = Call Attempts
2nd Digit = DTMF Dialing
3rd Digit = RPS Ring Count 		(1 to 15 attempts)
(0 = Pulse, 1 = Tone)
(0 = Disable, 1 to 14,
15 = Answer Machine)
06 I_?_I_?_I_?_I_?_I Receiver 1 Account Number (Last 4 digits)
07 I_X_I_X_I_X_I_X_I_X_I_X_I Receiver 1 Phone Number (First 6 digits)
08 I_0_I_1_I_8_I_?_I_?_I_?_I Receiver 1 Phone Number (Middle 6 digits)
09 I_?_I_?_I_?_I_?_I_?_I_?_I Receiver 1 Phone Number (Last 6 digits)
SHIFT + * = *
SHIFT + # = #
SHIFT + 5 = 2-second delay
SHIFT + 0 = SPACE/ERASE
10 I_X_I_X_I_X_I_X_I Receiver 2 Account Number (Not used)
11 I_X_I_X_I_X_I_X_I_X_I_X_I Receiver 2 Phone Number (Not used)
12 I_X_I_X_I_X_I_X_I_X_I_X_I Receiver 2 Phone Number (Not used)
13 I_X_I_X_I_X_I_X_I_X_I_X_I Receiver 2 Phone Number ( Not used)
14 I_0_I_1_I Status Report Code & Receiver
1st digit = Report Code
2nd digit = Receiver
(1 to F (15), 0 = Disabled)
(1 = Receiver 1, 2 = Receiver 2)
15 I_0_I_1_I Shunt Report Report Code & Recvr
1st digit = Report Code
2nd digit = Receiver Select
(1 to F (15), 0 = Disabled)
(1 = Receiver 1, 2 = Receiver 2)
16 I_8_I_1_I_3_I Test Report
1st digit = Report Code
2nd digit = Receiver Select
3rd digit = Test Interval
(1 to F (15), 0 = Disabled)
(1 = Receiver 1, 2 = Receiver 2)

0 = 1 Day 9 = 19 Days
1 = 3 Days *0 = 21 Days
3 = 5 Days *1 = 23 Days
4 = 7 Days *2 = 25 Days
5 = 9 Days *3 = 25 Days
8 = 17 Days *4 = 29 Days
*5 = 31 Days
31 I_1_I_1_I_0_I_3_I_0_I_1_I Channel 1 (Fire) Programming
1st digit = Report Code
2nd digit = Receiver Select
3rd digit = Dialer Delay x10 sec )
4th digit = Swinger Killer
5th digit = Restoral Report Code
6th digit = Restore Receiver Select
(1 to F (15), 0 = Disabled)
(1 = Receiver 1, 2 = Receiver 2)
(0 = 10ms, to *5 = 150 sec)
(2 to F (15), 0 = Disabled)
(1 to F (15), 0 = Disabled)
(1 = Receiver 1, 2 = Receiver 2)
32 I_2_I_1_I_0_I_3_I_0_I_1_I Channel 2 (Medical) Programming
33 I_3_I_1_I_0_I_3_I_0_I_1_I Channel 3 (Environmental) Programming
34 I_4_I_1_I_0_I_3_I_0_I_1_I Channel 4 (Perimeter/Tamper) Programming
35 I_5_I_1_I_0_I_3_I_0_I_1_I Channel 5 (Interior) Programming
36 I_6_I_1_I_0_I_3_I_0_I_1_I Channel 6 (Panic) Programming
37 I_7_I_1_I_0_I_3_I_0_I_1_I Channel 7 (Ambush) Programming
38 I_0_I_1_I_0_I_3_I_0_I_1_I Channel 8 (Trouble) Programming
(Channel 8 reporting is disabled due to its tendency to send runaway signals)
Set LOCAL REMOTE jumper to REMOTE when local programming downloaded back into dialer