1. Home
  2. Apex
  3. Destiny 4100
  4. Apex Destiny
 

Apex Destiny 4100 Program

Enter Program 9173 (System says “Enter Program Mode“)
Exit Program 515 (System says “Exit Program Mode“
Move to location Enter 3-digit location, good location = 1 beep, bad location = 3 beeps
Enter Data 3-digit entry only, system will repeat back to you
Clear Entry Press * or A
Read Location Press # or H to listen to what is in a location
Diagnostic LED (Shows Dialer activity)
Extended ON + one short On/Off Successful Communication
Two Short On/Off’s No Phone Number programmed
Extended ON + 3 On/Off’s No Dial Tone detected
Extended ON + 4 On/Off’s No Handshake or Central Station
Extended ON + 5 On/Off’s No Kissoff (Check format)
Not All Options are listed but should be enough to help most tech questions
Zone Programming
Location Description Default
166 Total Number of Wireless Zones (5700 Series) 000 (none)
167 Total Number of Hardwire Zones 000 (none)
168 Receiver Residence Code (House Code) 010 (House Code 10)
(must match Ademco 5700 series wireless sensor dip switches)
Location Description Default Options
001 Zone 1 Definitions 081 (Exterior Delay 1)
002 Zone 2 Definitions 082 (Exterior Delay 2) 015 = Zone Disabled
003 Zone 3 Definitions 080 (Exterior Instant) 019 = Interior Instant
004 Zone 4 Definitions 080 (Exterior Instant) 020 = Interior Delay 1
005 Zone 5 Definitions 080 (Exterior Instant) 021 = Interior Delay 2
006 Zone 6 Definitions 080 (Exterior Instant) 024 = 24 Hr Silent Panic
007 Zone 7 Definitions 026 (Interior Follower) 026 = Interior Follower
008 Zone 8 Definitions 026 (Interior Follower) 080 – Exterior Instant
009 Zone 9 Definitions 015 (Zone Disabled) 081 = Exterior Delay 1
010 Zone 10 Definitions 015 (Zone Disabled) 082 = Exterior Delay 2
011 Zone 11 Definitions 015 (Zone Disabled) 085 = 24 Hour Fire
012 Zone 12 Definitions 015 (Zone Disabled) 087 = 24 Hour Panic
013 Zone 13 Definitions 015 (Zone Disabled) 089 = 24 Hour Medical
014 Zone 14 Definitions 015 (Zone Disabled)
015 Zone 15 Definitions 015 (Zone Disabled) for more see page 9 in
016 Zone 16 Definitions 015 (Zone Disabled) the Installation Manual
499 2-Wire Smoke Loop Options 000 (Zone Disabled) Enter 013 to enable
Zone Voice Programming
To Program

  1. Press 536, keypad will say “Enter Zone” enter 2-digit zone number
  2. Enter 3-digit code for Word Definition CLICK HERE FOR COMPLETE LIST, keypad will repeat it
  3. Enter next word, maximum of 4 words, if less than 4 end with H or # key to save and exit
To Hear Descriptions

  1. Press 546, keypad will say “Enter Zone” enter 2-digit zone number
  2. Keypad will speak current Voice Description, end with H or * key
Zone Partitioning
158 Zone 1
159 Zone 2
160 Zone 3
161 Zone 4
162 Zone 5
163 Zone 6
164 Zone 7
165 Zone 8
166 Zone 9
167 Zone 10
168 Zone 11
169 Zone 12
170 Zone 13
171 Zone 14
172 Zone 15
173 Zone 16 		?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
? 		1 = Parition 1
2 = Partion 2
3 = Partion 3
4 = Partion 4
5 = Partion 5
6 = Partion 6
7 = Partion 7
8 = Partion 8

Add together for multiple
Partition access

User Codes
050 to 053 User Code 1 1234
054 to 057 User Code 2 Disabled
058 to 061 User Code 3 Disabled
062 to 065 User Code 4 Disabled
066 to 069 User Code 5 Disabled
070 to 073 User Code 6 Disabled
074 to 077 User Code 7 Disabled
078 to 081 User Code 8 Disabled
082 to 085 User Code 9 Disabled
086 to 089 User Code 10 Disabled
User Code Partitioning
148 User Code 1 0 1 = Parition 1
2 = Partion 2
3 = Partion 3
4 = Partion 4
5 = Partion 5
6 = Partion 6
7 = Partion 7
8 = Partion 8

Add together for multiple
Partition access

149 User Code 2 0
150 User Code 3 0
151 User Code 4 0
152 User Code 5 0
153 User Code 6 0
154 User Code 7 0
155 User Code 8 0
156 User Code 9 0
157 User Code 10 0
System Times
Location Description Default Recommend
034 Entry delay 1 (seconds) 020 030
035 Entry delay 2 (seconds) 020
036 Exit delay (seconds) 030 060
037 Alarm cut off and reset (minutes) 005 006
040 Fire Chirp (chirps in seconds) 000 (disabled)
041 Hardwire Fast Loop Response (x32ms) 002
042 Hardwire Slow Loop Response (x32ms) 005
043 Duration of AC loss (minutes) 010 010
044 Time between Control Batt Testing (days) 000
Communicator Programming
Location Description Default Recommend
516 Enter Phone 1 to Central Station Press H H or # # to exit
526 Speak Phone 1
521 Enter Account Number 1 Press H H or # # to exit
531 Speak Account Number 1
517 Enter Phone 2 to Central Station (Normally not used)
527 Speak Phone 1
522 Enter Account Number 2 (Normally not used)
532 Speak Account Number 2
363 Delay before Dialing (seconds) 002 002
364 Phone 1 Reporting Options 010 (Sescoa) 018 (Sescoa)
365 Phone 1 Format 000 (3/1) 008 (Contact ID)
366 Phone 2 Reporting Options 010 (Sescoa) 008 (Sescoa)
367 Phone 2 Format 000 (3/1) 008 (Contact ID)
368 Number of Dial Attempts 008 008
370 Touchtone (000) or Pulse (001) Dialing 000 (Tone) 000 (Tone)
371 Maximum Wait for Handshake (Seconds) 025
372 Hours until 1st Automatic Communicator Test 000
382 Days between Automatic Communicator Test 007 030
Misc Options
511 – Slow Speech (000), Fast Speech (001)
513 – Clear all Bypass, Troubles and Alerts
514 – Clear Long Term Memory
515 – Exit Program Mode
556 – Speak Long Term Memory
557 – Speak System Status
566 – Take System out of RF Strength Test
567 – Place System in RF Strength Test
568 – Initiate System for Direct-Connect Upload/Download
586 – Begin Auto Communicator Test Report Start Countdown
596 – System Reboot
606 – Speak Panel Revision Number
Report Codes
Dialer Options 001 = Dial Phone 1
002 = Dial Phone 2
004 = Enable 2-Way Voice
008 = Dial Alternate Number if 1st choice fails
128 = Record this into Event Memory Log
For 2-way use 133 ??? Add together for value to program into Dialer Options
For no 2-way use 129
Location Description Value
297 Exterior Instant Zone Report Code 003
330 Dialer Option 133 (Dial Phone 1, Enable 2-Way)
298 Exterior Delay 1 Zone Report Code 003
331 Dialer Option 133 (Dial Phone 1, Enable 2-Way)
299 Exterior Delay 2 Zone Report Code 003
332 Dialer Option 133 (Dial Phone 1, Enable 2-Way)
300 Interior Instant Zone Report Code 004
333 Dialer Option 133 (Dial Phone 1, Enable 2-Way)
301 Interior Delay 1 Zone Report Code 004
334 Dialer Option 133 (Dial Phone 1, Enable 2-Way)
302 Interior Delay 2 Zone Report Code 004
335 Dialer Option 133 (Dial Phone 1, Enable 2-Way)
303 Fire Zone Report Code 001
336 Dialer Option 133 (Dial Phone 1, Enable 2-Way)
304 Panic Report Code 002
337 Dialer Option 133 (Dial Phone 1, Enable 2-Way)
305 Silent Panic Report Code 002
338 Dialer Option 133 (Dial Phone 1, Enable 2-Way)
306 Emergency Panic Report Code 005
339 Dialer Option 133 (Dial Phone 1, Enable 2-Way)
307 Follower Report Code 004
340 Dialer Option 133 (Dial Phone 1, Enable 2-Way)
308 Auxiliary Output Report Code 005
341 Dialer Option 133 (Dial Phone 1, Enable 2-Way)
309 Duress Disarm Report Code 002
342 Dialer Option 133 (Dial Phone 1, Enable 2-Way)
310 Duress When Not Armed Report Code 002
343 Dialer Option 133 (Dial Phone 1, Enable 2-Way)
311 Zone Restore After Activation Report Code 009
344 Dialer Option 129 (Dial Phone 1)
312 Transmitter Low Battery Report Code 008
345 Dialer Option 129 (Dial Phone 1)
313 Transmitter Battery Restore Report Code 009
346 Dialer Option 129 (Dial Phone 1)
314 Zone Trouble Report Code 008
347 Dialer Option 001 (Dial Phone 1)
315 Zone Trouble Restore Report Code 009
348 Dialer Option 001 (Dial Phone 1)
318 Phone Line Restore Report Code 009
351 Dialer Option 000 (Dial Phone 1)
319 Open (Disarm) Report Code 011
352 Dialer Option 000 (Dial Phone 1)
320 Open (Disarm) After Activation Report Code 011
353 Dialer Option 000 (Dial Phone 1)
321 Close (Arm) Central Station Report Code 012
354 Dialer Option 000 (Dial Phone 1)
322 Close (Arm) with Open Zone (Force Arm) 012
355 Dialer Option 000 (Dial Phone 1)
323 Panel Low Battery Report Code 008
356 Dialer Option 129 (Dial Phone 1)
324 Panel Low Battery Restore Report Code 009
357 Dialer Option 129 (Dial Phone 1)
325 AC Fail Report Code 008
358 Dialer Option 129 (Dial Phone 1)
326 AC Restore Report Code 009
359 Dialer Option 129 (Dial Phone 1)
327 User Communicator Test Report Code 007
360 Dialer Option 129 (Dial Phone 1)
328 Automatic Communicator Test Report Code 007
361 Dialer Option 129 (Dial Phone 1)
329 Cancel Central Station Report Code 000
362 Dialer Option 129 (Disabled)
Installer Code
Location Description Default Recommend
383 1st Digit of Installer Code 009 009
384 2nd Digit of Installer Code 001 001
385 3rd Digit of Installer Code 007 007
386 4th Digit of Installer Code 003 003
Downloading/Remote Options
Location Description Default Recommend
380 Number of Rings before Pickup 010 010
388 Answering Machine Over-Ride Digit 011 (#) 011 (#)
407 Upload/Download Access Code 1st Digit 010 (*) 010
408 Upload/Download Access Code 2nd Digit 010 (*) 010
409 Upload/Download Access Code 3rd Digit 001 001
410 Upload/Download Access Code 4th Digit 002 002
399 Local Phone Access Code 1st Digit (1 to 4 digits) 010 (*) 010
400 Local Phone Access Code 1st Digit (1 to 4 digits) 011 (#) 011
401 Local Phone Access Code 1st Digit (1 to 4 digits) 255 255
402 Local Phone Access Code 1st Digit (1 to 4 digits) 255 255
396 Inactive Time before Hangup while in Phone Mode 015 (seconds)
397 Inactive while in Phone Program Mode 060 (seconds)
Two-Way Digit Assignments
Location Description Default
222 Rearrange Keypad phone digits (001 changes default) 000
223 0 = Exit 2-way by going to keypad mode or hanging up 000
224 1 = Microphone #1 On 001
225 2 = Microphone #2 On 002
226 3 = Microphone #3 On 003
227 4 = Microphone #1 Off 004 factory
228 5 = Microphone #2 Off 005 Defaults
229 6 = Microphone #3 Off 006 Leave Alone
230 7 = High microphone sensitivity 007
231 8 = Normal microphone sensitivity 008
232 9 = All microphones on 009
233 * = Listen 010
234 # = Talk 011