Alarmlock Eagle 8000DL Program
| Enter Program |
1. Hold 8 key for 3 seconds, keypad will beep 2. Enter 4 5 6 7 8 9, display should show dash |
| Move to Location |
1. Press [S], display will show 3 dashs, enter 3-digit location 2. What is programmed in location will display, use 4 and 7 keys to change data 3. Once correct data displays press 2 to move to next location |
| Exit Program |
1. Hold 8 key 3 seconds, keypad will flash and beep 2. Enter 4 5 6 7 8 9, display should return to normal |
| IF something gets screwed up power down then up, there is 30 seconds to get into program | |
| To program REPORT OPTIONS in locations 166 to 185 see below Diagram | |||
 |
|||
| Add location together and enter sum in location | |||
|
Example: Enable Reporting for Zones 1 to 6, Keypad Panic, Fire, Duress, Fire Trle, AC Fail and Low Bat 1. Press B/A then 1 6 6 to move to Location 166 2. Add ZONE 1 (1) + ZONE 2 (2) + ZONE 3 (4) + ZONE 4 (8) = 15 or F, enter the F in location 166 3. Press 2 key to move to 167 4. Add Zone 5 (1) + Zone 6 (2) + Keypad Panic (8) = 11 (B), enter the B in location 167 5. Press 2 key to move to 168 6. Add FIRE ZONE (1) + AMBUSH (2) + FIRE TROUBLE (4) = 7, enter the 7 in location 168 7. Press 2 key to move to 169 8. Add AC FAIL (2) + LOW BAT (4) = 6, enter the 6 in location 169 |
|||
| 166 – Report Enable Zns 1 to 4 | I_F_I | 168 – Fire/Duress, Fire Trouble | I_7_I |
| 167 – Report Enable Zns 5, 6 & Panic | I_D_I | 169 – AC Fail/Low Bat Trouble | I_6_I |
| 170 – 171 – Restores Enabled | I_ _I_ _I | 172 – 173 – Misc Restores | I_ _I_ _I |
| (Blank out this section) | (Blank out this section) | ||
| 184 – 185 – Zone Restores | I_ _I_ _I | ||
| (Blank out this section) | |||
| 000 – 001 Zone 1 Report Code | I_3_I_1_I | 014 – 015 Keypad Panic | I_2_I_1_I |
| 002 – 003 Zone 2 Report Code | I_3_I_2_I | 016 – 017 Fire Panic/Smoke | I_2_I_3_I |
| 004 – 005 Zone 3 Report Code | I_3_I_3_I | 018 – 019 Hostage/Duress | I_2_I_2_I |
| 006 – 007 Zone 4 Report Code | I_3_I_4_I | 020 – 021 Fire Trouble | I_7_I_6_I |
| 008 – 009 Zone 5 Report Code | I_3_I_5_I | 022 – 023 Day Zone Trouble | I_ _I_ _I |
|
010 – 011 Zone 6 Report Code (If Smoke on Zone 6 program 1 6) |
I_3_I_6_I | 024 – 025 Test Timer | I_ _I_ _I |
| 026 – 027 AC Failure | I_7_I_9_I | ||
| 028 – 029 Low Battery | I_7_I_8_I | ||
| (I_ _I_ _I = Blank out Locations with 5 key) | |||
| 040 – 041 Zone 1 Restore | I_ _I_ _I | 056 – 057 Fire Panic/Smoke | I_ _I_ _I |
| 042 – 043 Zone 2 Restore | I_ _I_ _I | 058 – 059 Not Used | I_ _I_ _I |
| 044 – 045 Zone 3 Restore | I_ _I_ _I | 060 – 061 Fire Trouble | I_ _I_ _I |
| 046 – 047 Zone 4 Restore | I_ _I_ _I | 062 – 063 Not Used | I_ _I_ _I |
| 048 – 049 Zone 5 Restore | I_ _I_ _I | 064 – 065 Not Used | I_ _I_ _I |
| 050 – 051 Zone 6 Restore | I_ _I_ _I | 066 – 067 AC Trouble Restore | I_ _I_ _I |
| (Blank out everything with 5 key) | 068 – 069 Low Battery Restore | I_ _I_ _I | |
| 030 – 031 Closing User 1 | I_ _I_ _I | 070 – 071 Opening User 1 | I_D_I_1_I |
| 032 – 033 Closing User 2 | I_ _I_ _I | 072 – 073 Opening User 2 | I_D_I_1_I |
| 034 – 035 Closing User 3 | I_ _I_ _I | 074 – 075 Opening User 3 | I_D_I_1_I |
| 036 – 037 Closing User 4 | I_ _I_ _I | 076 – 077 Opening User 4 | I_D_I_1_I |
| 038 – 039 Force Arm | I_ _I_ _I (These are Cancels, see also section 179) | ||
| 174 – Select User Closings | I_ _I_ _I | 176 – Select User Openings | I_ _I_ _I |
| (I_ _I_ _I = Blank out Locations with 5 key) | |||
| Telephone Number 1 | (Last 4 of Account must be entered in each section) | |
|
Group 1 100 – 103 Last 4 of Account I_?_I_?_I_?_I_?_I |
Group 2 104 – 107 Last 4 of Account I_?_I_?_I_?_I_?_I |
Opening/Closings 108 – 111 Last 4 Account I_?_I_?_I_?_I_?_I |
| Telephone Number 2 | (Blank These Sections Out with 5 key) | |
|
132 – 135 Last 4 of Account I_ _I_ _I_ _I_ _I |
136 – 139 Last 4 of Account I_ _I_ _I_ _I_ _I |
140 – 143 Last 4 Account I_ _I_ _I_ _I_ _I |
| 112 – 113 Report Format Phone 1 | I_9_I_2_I |
|
First Digit Blank = Ademco/Silent Knight Slow 1 = Sescoa, Vertex, DCI, Franklin 2 = Radionics Fast 3 = Silent Knight Fast 4 = Radionics, DCI, Franklin Slow 5 = Universal Hi Speed 8 = 2300 Handshake (Add this to above numbers) |
Second Digit Blank = Extended or Single Digit 1 = Single Digit 2 = 2-Digit (4/2) 4 = Sumcheck |
| 114 – 115 Receiver 1 Options | I_ _I_ _I (Add 9 in 115 if 9 is needed to dial out) |
| 116 – 131 Receiver 1 Phone (16 Digits) | I_E_I_1_I_8_I_?_I_?_I_?_I_?_I_?_I_?_I_?_I_?_I |
| 144 – 145 Report Format Phone 2 | I_ _I_ _I (Leave these blank) |
| 146 – 147 Receiver 2 Options | I_ _I_ _I (Leave these blank) |
| 148 – 163 Receiver 2 Phone | I_N_I_O_I_T_I_ _I_U_I_S_I_E_I_D_I_ _I_ _I_ _I |
| 269 Rings before Download | I_A_I (10 rings until Answer) |
| 270 – 285 Download Phone | I_B_I_L_I_A_I_N_I_K_I_ _I_O_I_U_I_T_I_ _I_ _I |
| To program sections 084 to 216 see below Diagram | |||
 |
|||
|
Add location together and enter sum in location Example: Program Zones 1, 3 4, 5 and 6 for Door Chime 1. Press B/A then B/A again then 8 8 to enter Location 088 2. Add Zone 1 (1) + Zone 2 (2) + Zone 4 (8) = 11 or B, enter B in location 088 3. Press 2 key to move to 089 4. Add Zone 5 (1) + Zone 6 (2) = 3, enter 3 in location 089 |
|||
| 084 – 085 Swinger Shutdown | I_F_I_3_I | (Swinger enabled on all zones) | |
| 086 – 087 No EOL Zone Resistors | I_ _I_ _I | (Blank = No EOL, F 3 = EOL all zones) | |
| 088 – 089 Chime Zones 1 to 6 | I_ _I_ _I | (Turns on/off chimes per zone) | |
| 090 – 091 Never Arm | I_ _I_ _I | (Leave blank) | |
| 092 – 093 PIR Zone | I_ _I_ _I | (Program PIR zones here. also see 206 – 207) | |
| 096 – 099 Untimed Output to Lug E15 | I_F_I_B_I | (Normally not programmed) | |
| 164 – 165 KP Sounder on Alarm | I_ _I_ _I | (Leave blank) | |
| 186 – 187 Day Zone | I_ _I_ _I | (Leave blank) | |
| 188 – 189 Priority Zone W/Bypass | I_ _I_ _I | (Leave blank) | |
| 190 – 191 Priority Zone | I_F_I_3_I | (Default = F 3, leave alone) | |
| 192 – 193 Remove Auto-Bypass | I_ _I_ _I | (Leave blank) | |
| 194 – 195 Selective Bypass | I_F_I_3_I | (Default = F 3, leave alone) | |
| 196 – 197 Group Bypass | I_?_I_?_I | (any zone here will bypass by B/A key twice) | |
| 198 – 199 24 hr Protection | I_ _I_D_I | (Use if Hold-Up buttons on a zone) | |
| 200 – 201 Auto Reset | I_F_I_D_I | (Default = F D, leave alone) | |
| 202 – 203 Entry/Exit Delay 1 Zones | I_?_I_?_I | (Program which zones are Delay 1) | |
| 204 – 205 Entry/Exit Delay 2 Zones | I_?_I_?_I | (Program which zones are Delay 2) | |
| 206 – 207 Interior Follower Zones | I_?_I_?_I | (Program PIR zones here. also see 092 – 093) | |
| 208 – 209 Abort Delay per Zone | I_ _I_ _I | (Leave blank) | |
| 210 – 211 Burglary Output per Zone | I_F_I_F_I | (Unless using Silent Panic leave at F 3) | |
| 212 – 213 Timed Negative Output | I_ _I_ _I | (Leave blank) | |
| 214 – 215 7ms Loop Response | I_ _I_ _I | (Leave blank) | |
| 216 – 217 50ms Loop Response | I_ _I_ _I | (Leave blank) | |
| 236 – 237 Hostage/Duress Code | I_9_I_9_I |
| 238 – 243 User Program Code | I_1_I_2_I_3_I_4_I_5_I_6_I |
|
Note: allows customer to change User codes, leave at default If Changed Make a note on the account and on the panel. |
|
| 244 – 249 Installer/Dealer Code | I_4_I_5_I_6_I_7_I_8_I_9_I |
| (User Codes MUST be programmed at User Level, not in Programming) | |
| Add each section, place total in box | (Example: 1 + 4 + 8 = 13 or “D”) | I_ _I = Blank Out with 5 key | |||
| 078 | I_4_I | 178 | I_2_I | 182 | I_6_I |
|
1 = Desplay Day Zone/Reset 2 = Fail to Com on NTO Lug 4 = User 5 Quick Arm 8 = User 5 Report as User 1 |
1 = Touchtone Dialing 2 = Touchtone/Rotary Backup 3 = Backup Reporting 4 = Double Reporting |
1 = Disable Fault Find 2 = Enable Keypad Panic 4 = Enable Comunicator Test 8 = Disable Bell Test |
|||
| 079 | I_ _I | 179 | I_1_I | 183 | I_ _I |
|
1 = User 5 Service Code 2 = Disable Day Zn Report 4 = Reserved 8 = Reserved |
1 = Opening after Alarm 2 = Force Arm 4 = Status Report 8 = Split Report |
1 = Disable any Bypass 2 = No Open Rep Alarm on Zn 6 4 = Incl Man Byp in Force Arm 8 = Reserved |
|||
| 080 | I_ _I | 180 | I_2_I | ||
|
1 = Direct KP Panic to Ambush 2 = Reserved 4 = Disable Callback Download 8 = Disable Function 6 Download |
1 = Audible Test on Arming 2 = Auto-Reset after Timeout 4 = Power Up in Last State 8 = Sounder Output on E4 Lug |
||||
| 081 | I_ _I | 181 | I_3_I | ||
|
1 = Watch on With Group Byp 2 = Chime On with Group Byp 4 = Display Chime Zones 8 = Disable Display Bypass |
1 = Pulsing Fire 2 = Reset Fire Zone 4 = Reserved 8 = Reset Tst Timer on Report |
||||
| 082 | I_1_I | ||||
|
1 = Enable Download w/Ans Machine 2 = Remote Status LED on NTO Lug 4 = Reserved 8 = Reserved |
|||||
|
E/E Times found by dividing desired time by 16 Enter 1st digit of resut in second box and 2nd digit of result in 1st box (wierd ain’t it?) |
||
| 094 – 095 Sensor Watch | I_ _I_ _I | (Leave both blank, not used) |
| 218 – 219 Exit Delay | I_C_I_3_I | (60 seconds) |
| 220 – 221 Entry Delay 1 | I_E_I_1_I | (30 seconds) |
| 222 – 223 Entry Delay 2 | I_E_I_1_I | (30 seconds) |
| 224 – 225 Burg Timeout | I_6_I_ _I | (6 minutes, leave 2nd entry blank) |
| 228 – 229 Fire Timout | I_F_I_ _I | (Unlimited, leave 2nd entry blank) |
| 230 – 231 Chime Duration | I_4_I_ _I | (1/2 second Chime, leave 2nd entry blank) |
| 232 – 233 Abort Delay | I_ _I_ _I | (Leave both blank, not used) |
| 250 – 251 Test Timer | I_ _I_ _I | (Leave both blank, not used) |