Ademco Vista 50P Program

This is VERY general programming, about enough to get it downloaded
Enter Program 4140 + 8 + 0 + 0 (Display should show 00)
or Power down then back up and press * and # within 1 minute
(If exiting programming you can re-enter within 1 minute by pressing * and #)
Move to Location * + Location
View Location # + Location (Display will read off one digit at a time)
Exit Program 1. *98 OR 2. *99 if needing to re-enter programming later by Code + 8 + 0 + 0

All Zone programming is done by # 93 menu, Click to go to section
ZONE PROG? 0 (No) for next menu, 1 (Yes) to enter this menu (Completed)
ALPHA PROG? 0 (No) for next menu, 1 (Yes) to enter this menu (Under Construction)
DEVICE PROGR? 0 (No) for next menu, 1 (Yes) to enter this menu (Under Construction)
RLY VOICE DESCR? 0 (No) for next menu, 1 (Yes) to enter this menu (Under Construction)
CUSTOM INDEX? 0 (No) moves back to start, 1 (Yes) to enter this menu (Under Construction)

*00 – Installer Code I_4_I_1_I_4_I_0_I

(Use this section or #93 both does the same thing)


*02 Zone Types Zone 1 to 8
    I_ _I_ _I Zone 1
    I_ _I_ _I Zone 2
    I_ _I_ _I Zone 3
    I_ _I_ _I Zone 4
    I_ _I_ _I Zone 5
    I_ _I_ _I Zone 6
    I_ _I_ _I Zone 7
    I_ _I_ _I Zone 8
*03 Zone Types Zone 9 to 16
    I_ _I_ _I Zone 9
    I_ _I_ _I Zone 10
    I_ _I_ _I Zone 11
    I_ _I_ _I Zone 12
    I_ _I_ _I Zone 13
    I_ _I_ _I Zone 14
    I_ _I_ _I Zone 15
    I_ _I_ _I Zone 16

00 = Disabled
01 = Entry/Exit 1
02 = Entry/Exit 2
03 = Perimiter
04 = Interior Follower
05 = Day/Night Burg
06 = Silent Holdup
07 = 24H Audible (Police)
08 = 24H AUX (Medial)
09 = Fire
10 = Interior/Delay
20 = Arm Stay
21 = Arm Away
22 = Disarm
23 = No Alarm Response
*04 Zone Types Zone 17 to 24  
    I_ _I_ _I Zone 17
    I_ _I_ _I Zone 18
    I_ _I_ _I Zone 19
    I_ _I_ _I Zone 20
    I_ _I_ _I Zone 21
    I_ _I_ _I Zone 22
    I_ _I_ _I Zone 23
    I_ _I_ _I Zone 24
*05 Zone Types Zone 25- 27 & Panics   
    I_ _I_ _I Zone 25
    I_ _I_ _I Zone 26
    I_ _I_ _I Zone 27
    I_0_I_0_I Not Used
    I_0_I_5_I Polling Loop Short
    I_0_I_9_I 1 & * A Panic (Fire) Key
    I_0_I_8_I 3 & # C Panic (Medical) Key
    I_0_I_7_I * & # B Panic (Police) Key

*09 – Entry Delay 1 I_0_I_2_I 00 to 15 x15 Seconds (Partition Specific)

*10 – Exit Delay 1 I_0_I_4_I 00 to 15 x15 Seconds (Partition Specific)

*11 – Entry Delay 2 I_0_I_2_I 00 to 15 x15 Seconds (Partition Specific)

*12 – Exit Delay 2 I_0_I_2_I 00 to 15 x15 Seconds (Partition Specific)

*13 – Alarm Sounder Duration I_0_I_4_I 00 to 15 x15 Minutes (Partition Specific)

*14 – Zone 9 Response I_0_I 0 = Slow
1 = Fast

*15 – Keyswitch Assignment I_0_I 0 = Disabled
1 = Partition 1
to
8 = Partition 8

*16 Arming Ding I_0_I 0 = No (Partition Specific)
1 = Yes

*17 AC Loss Sounding I_1_I 0 = No
1 = Yes

*18 – AC Loss Siren I_0_I 0 = No
1 = Yes

*19 – Random AC Loss Report I_0_I 0 = No
1 = Yes

*20 4285 Phone Module Code I_0_I_?_I_0_I_?_I 1st Digit = 01 to 09
2nd Digit = 11 (*) or 12 (#)

*21 – Fire Timout I_1_I 0 = No
1 = Yes

*22 Keypad Panics Enable I_1_I Fire Panic
I_1_I Medical Panic
I_1_I Police Panic
0 = No (Partition Specific)
1 = Yes

*23 – Multiple Alarms I_1_I 0 = No (Partition Specific)
1 = Yes

*24 Ignore Exp Module Tamper I_1_I 0 = No
1 = Yes

*25 Burg Trigger for Zone Type 8 I_0_I 0 = No
1 = Yes

*26 Intelligent Test Reporting I_0_I 0 = No
1 = Yes

*27 – Test Report Interval I_6_I_7_I_2_I 00 = Disabled
001 to 999 Hours

*28 – Power Up in Previous State I_1_I 0 = No
1 = Yes

*29 – Quick Arm I_1_I 0 = No
1 = Yes

*30 – Touch Tone Dialing I_1_I 0 = Pulse
1 = Touch Tone

*31 – PABX Access Code I_ _I_ _I_ _I_ _I

*32 – Primary Account Number I_0_I_?_I I_0_I_?_I I_0_I_?_I I_0_I_?_I (2 digit entries) (Partition-Specific)
Hex B = 11, C = 12, D = 13, E = 14, F = 15

*33 – Primary Phone Number (12 Digits) I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
(# + 11 = *# + 12 = #, # + 13 = 2.5 second pause)

*34 – Secondary Phone Number (12 Digits) I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I

*35 – Download Phone Number (12 Digits) I_1_I_8_I_0_I_0_I_7_I_6_I_2_I_7_I_8_I_3_I_1_I_ _I

*36 – CSID Number I_1_I_5_I_1_I_5_I_1_I_5_I_1_I_5_I_1_I_5_I_1_I_5_I_1_I_5_I_1_I_5_I

*37 Download Command Enable I_1_I Dialer Shutdown
I_1_I Sys Shutdown
I_0_I Not Used
I_1_I Remote Bypass
I_1_I Remote Disarm
I_1_I Remote Arm
I_1_I Upload Enable
I_1_I Download Enable
0 = No
1 = Yes

*38 – Prevent Fire Zone Bypass I_0_I_0_I (All Zones Bypassable)

*39 O/C Report for Installer I_0_I 0 = No
1 = Yes

*40 O/C Report for Keyswitch I_0_I 0 = No
1 = Yes

*41 – Normally Closed Zones 2-8 I_0_I 1 = NC Loops
0 = EOL Resistors

*42 – Dial Tone Pause I_0_I I 0 = 5 seconds
1 = 11 seconds
2 = 30 seconds

*43 – Dial Tone Detection I_1_I 0 = Pause then Dial
1 = Wait for Dial Tone

*44 – Ring Detection Count I_1_I_5_I 15 = Answering Machine Over-Ride

*45 – Primary Format I_1_I 0 = Ademco Lo
1 = Contact ID
2 = Ademco High Speed
3 = Ademco Express

*46 Low Speed Format Primary I_0_I 0 = Ademco Low Speed
1 = Sescoa/Radionics

*47 – Secondary Format I_1_I 0 = Ademco Lo
1 = Contact ID
2 = Ademco High Speed
3 = Ademco Express

*48 Low Speed Frmt Secondary I_0_I 0 = Ademco Low Speed
1 = Sescoa/Radionics

*49 – Checksum Verification I_0_I Primary
I_0_I Secondary
0 = No
1 = Yes

*50 – Sescoa Radionics Select I_0_I 0 = Sescoa
1 = Radionics

*51 – Dual Reporting I_0_I 0 = No
1 = Yes

*52 Stndrd/Exp Primary Report I_0_I Alarms
I_0_I Restore
I_0_I Bypass
I_0_I Trouble
I_0_I Open/Close
I_0_I Low Battery
0 = Standard
1 = Expanded

*53 Stndrd/Exp Second Report I_0_I Alarms
I_0_I Restore
I_0_I Bypass
I_0_I Trouble
I_0_I Open/Close
I_0_I Low Battery

0 = Standard
1 = Expanded
(Use this section or #93 both does the same thing)


*54 Alarm Report Codes Zone 1 to 8
    I_1_I_1_I Zone 1
    I_1_I_1_I Zone 2
    I_1_I_1_I Zone 3
    I_1_I_1_I Zone 4
    I_1_I_1_I Zone 5
    I_1_I_1_I Zone 6
    I_1_I_1_I Zone 7
    I_1_I_1_I Zone 8
*55 Extended Report Codes Zone 1 to 8
    I_0_I_0_I Zone 1
    I_0_I_0_I Zone 2
    I_0_I_0_I Zone 3
    I_0_I_0_I Zone 4
    I_0_I_0_I Zone 5
    I_0_I_0_I Zone 6
    I_0_I_0_I Zone 7
    I_0_I_0_I Zone 8

*56 Alarm Report Codes Zone 9 to 16
    I_1_I_1_I Zone 9
    I_1_I_1_I Zone 10
    I_1_I_1_I Zone 11
    I_1_I_1_I Zone 12
    I_1_I_1_I Zone 13
    I_1_I_1_I Zone 14
    I_1_I_1_I Zone 15
    I_1_I_1_I Zone 16
*57 Extended Report Codes Zone 9 to 16
    I_0_I_0_I Zone 9
    I_0_I_0_I Zone 10
    I_0_I_0_I Zone 11
    I_0_I_0_I Zone 12
    I_0_I_0_I Zone 13
    I_0_I_0_I Zone 14
    I_0_I_0_I Zone 15
    I_0_I_0_I Zone 16

*58 – Supervisory/Restore Zones 1 to 16
    I_0_I_0_I Alarm Restoral
    I_0_I_0_I Trouble
    I_0_I_0_I Trouble Restore
    I_0_I_0_I Bypass
    I_0_I_0_I Bypass Restore

*59 Alarm Report Codes Zone 17 to 24
    I_1_I_1_I Zone 17
    I_1_I_1_I Zone 18
    I_1_I_1_I Zone 19
    I_1_I_1_I Zone 20
    I_1_I_1_I Zone 21
    I_1_I_1_I Zone 22
    I_1_I_1_I Zone 23
    I_1_I_1_I Zone 24
*60 Extended Report Codes Zone 17 to 24
    I_0_I_0_I Zone 17
    I_0_I_0_I Zone 18
    I_0_I_0_I Zone 19
    I_0_I_0_I Zone 20
    I_0_I_0_I Zone 21
    I_0_I_0_I Zone 22
    I_0_I_0_I Zone 23
    I_0_I_0_I Zone 24

*61 Alarm Report Codes Zone 25 to 32
    I_1_I_1_I Zone 25
    I_1_I_1_I Zone 26
    I_1_I_1_I Zone 27
    I_1_I_1_I Zone 28
    I_1_I_1_I Zone 29
    I_1_I_1_I Zone 30
    I_1_I_1_I Zone 31
    I_1_I_1_I Zone 32
*62 Extended Report Codes Zone 25 to 32
    I_0_I_0_I Zone 25
    I_0_I_0_I Zone 26
    I_0_I_0_I Zone 27
    I_0_I_0_I Zone 28
    I_0_I_0_I Zone 29
    I_0_I_0_I Zone 30
    I_0_I_0_I Zone 31
    I_0_I_0_I Zone 32

*63 – Supervisory/Restore Zones 17 – 32
    I_0_I_0_I Alarm Restoral
    I_0_I_0_I Trouble
    I_0_I_0_I Trouble Restore
    I_0_I_0_I Bypass
    I_0_I_0_I Bypass Restore

*64 Alarm Report Codes Zone 33 to 40
    I_1_I_1_I Zone 33
    I_1_I_1_I Zone 34
    I_1_I_1_I Zone 35
    I_1_I_1_I Zone 36
    I_1_I_1_I Zone 37
    I_1_I_1_I Zone 38
    I_1_I_1_I Zone 39
    I_1_I_1_I Zone 40
*65 Extended Report Codes Zone 33 to 40
    I_0_I_0_I Zone 33
    I_0_I_0_I Zone 34
    I_0_I_0_I Zone 35
    I_0_I_0_I Zone 36
    I_0_I_0_I Zone 37
    I_0_I_0_I Zone 38
    I_0_I_0_I Zone 39
    I_0_I_0_I Zone 40

*66 Alarm Report Codes Zone 41 to 48
    I_1_I_1_I Zone 41
    I_1_I_1_I Zone 42
    I_1_I_1_I Zone 43
    I_1_I_1_I Zone 44
    I_1_I_1_I Zone 45
    I_1_I_1_I Zone 46
    I_1_I_1_I Zone 47
    I_1_I_1_I Zone 48
*67 Extended Report Codes Zone 41 to 48
    I_0_I_0_I Zone 41
    I_0_I_0_I Zone 42
    I_0_I_0_I Zone 43
    I_0_I_0_I Zone 44
    I_0_I_0_I Zone 45
    I_0_I_0_I Zone 46
    I_0_I_0_I Zone 47
    I_0_I_0_I Zone 48

*68 – Supervisory/Restore Zones 33 to 48
    I_0_I_0_I Alarm Restoral
    I_0_I_0_I Trouble
    I_0_I_0_I Trouble Restore
    I_0_I_0_I Bypass
    I_0_I_0_I Bypass Restore

*69 Alarm Report Codes Zone 49 to 56
    I_1_I_1_I Zone 49
    I_1_I_1_I Zone 50
    I_1_I_1_I Zone 51
    I_1_I_1_I Zone 52
    I_1_I_1_I Zone 53
    I_1_I_1_I Zone 54
    I_1_I_1_I Zone 55
    I_1_I_1_I Zone 56
*70 Extended Report Codes Zone 49 to 56
    I_0_I_0_I Zone 49
    I_0_I_0_I Zone 50
    I_0_I_0_I Zone 51
    I_0_I_0_I Zone 52
    I_0_I_0_I Zone 53
    I_0_I_0_I Zone 54
    I_0_I_0_I Zone 55
    I_0_I_0_I Zone 56

*71 Alarm Report Codes Zone 57 to 64
    I_1_I_1_I Zone 57
    I_1_I_1_I Zone 58
    I_1_I_1_I Zone 59
    I_1_I_1_I Zone 60
    I_1_I_1_I Zone 61
    I_1_I_1_I Zone 62
    I_1_I_1_I Zone 63
    I_1_I_1_I Zone 64
*72 Extended Report Codes Zone 57 to 64
    I_0_I_0_I Zone 57
    I_0_I_0_I Zone 58
    I_0_I_0_I Zone 59
    I_0_I_0_I Zone 60
    I_0_I_0_I Zone 61
    I_0_I_0_I Zone 62
    I_0_I_0_I Zone 63
    I_0_I_0_I Zone 64

*73 – Supervisory/Restore Zones 49 – 64
    I_0_I_0_I Alarm Restoral
    I_0_I_0_I Trouble
    I_0_I_0_I Trouble Restore
    I_0_I_0_I Bypass
    I_0_I_0_I Bypass Restore

*74 Alarm Report Codes Zone 81 to 88
    I_1_I_1_I Zone 81
    I_1_I_1_I Zone 82
    I_1_I_1_I Zone 83
    I_1_I_1_I Zone 84
    I_1_I_1_I Zone 85
    I_1_I_1_I Zone 86
    I_1_I_1_I Zone 87 VIP Mdl Sprvsn
    I_1_I_1_I Zone 88 Rcver missing xmitter
*75 Extended Report Codes Zone 81 to 88
    I_0_I_0_I Zone 81
    I_0_I_0_I Zone 82
    I_0_I_0_I Zone 83
    I_0_I_0_I Zone 84
    I_0_I_0_I Zone 85
    I_0_I_0_I Zone 86
    I_0_I_0_I Zone 87
    I_0_I_0_I Zone 88

*76 Alarm Report for RF RCVR & Panics
    I_0_I_0_I Zone 89 Rcver not Responding
    I_0_I_0_I Zone 90 Rcver missing xmitter
    I_0_I_0_I Zone 91 Rcver not Responding
    I_1_I_1_I Duress
    I_1_I_1_I Zone 97 Polling Loop Short
    I_1_I_1_I Zone 95 1 & * A Fire Panic Key
    I_1_I_1_I Zone 96 3 & # C Medical Panic Key
    I_1_I_1_I Zone 99 * & # B Police Panic Key
*77 Extended Report for RF RCVR & Panics
    I_0_I_0_I Zone 89
    I_0_I_0_I Zone 90
    I_0_I_0_I Zone 91
    I_0_I_0_I Duress
    I_0_I_0_I Zone 97
    I_0_I_0_I Zone 95
    I_0_I_0_I Zone 96
    I_0_I_0_I Zone 99

*78 – Supervisory/Restore Zones 87 – 99
    I_0_I_0_I Alarm Restoral
    I_0_I_0_I Trouble
    I_0_I_0_I Trouble Restore
    I_0_I_0_I Bypass
    I_0_I_0_I Bypass Restore

*79 Zone Type Restores 1 -8     I_0_I_0_I_0_I_0_I_0_I_0_I_0_I_0_I     0 = Disable
1 = Enable
*80 Zone Type Restores 9 -10 I_0_I_0_I 0 = Disable
1 = Enable

*81 – System Non-Alarm Codes
    I_0_I_0_I Close
    I_0_I_0_I Open
    I_1_I_1_I Low Battery
    I_1_I_1_I Low Battery Restore
    I_1_I_1_I AC Loss
    I_1_I_1_I AC Loss Restore
    I_1_I_1_I Test
    I_0_I_0_I Power
    I_1_I_1_I Cancel
    I_0_I_0_I Program Tamper
*82 – System Non-Alarm Codes 2nd Digit
    I_0_I_0_I Close
    I_0_I_0_I Open
    I_0_I_0_I Low Battery
    I_0_I_0_I Low Battery Rest
    I_0_I_0_I AC Loss
    I_0_I_0_I AC Loss Rest
    I_0_I_0_I Test
    I_0_I_0_I Power
    I_0_I_0_I Cancel
    I_0_I_0_I Program Tamper
*83 First Test Report Time     I_0_I_0_I I_0_I_2_I I_0_I_0_I     00 in all boxes = instant
Day Hour Minutes Day 01 = Monday
*84 Swinger Shutdown I_0_I_3_I 00 = Disabled (Partition Specific)
01 to 15 Alarms

*85 Enable Dialer for Panics I_1_I Zn 95 Fire
I_1_I Zn 96 Medical
I_1_I Zn 99 Police
I_1_I Duress

0 = No (Partition Specific)
1 = Yes
*87 – Entry Warning I_1_I 0 = 3 Beeps (Partition Specific)
1 = Continous

*88 – Burg Alarm Comm Delay I_0_I 0 = Disabled (Partition Specific)
1 = 15 Seconds

*89 – Restore Report Timing I_0_I 0 = Instant
1 = At Bell Timeout
2 = At Disarm

*90 – 2nd Account Number I_0_I_?_I_0_I_?_I_0_I_?_I_0_I_?_I (2 digit entries)
Hex B = 11, C = 12, D = 13, E = 14, F = 15


To access Upper programming press *94, to return to lower programming press *99
the 1 isn’t part of location, to go to a Upper program location press * + 2-digits

(Use this section or #93 both does the same thing)


1*01 Zone Types Zone 28 to 32
    I_ _I_ _I Zone 28
    I_ _I_ _I Zone 29
    I_ _I_ _I Zone 30
    I_ _I_ _I Zone 31
    I_ _I_ _I Zone 32
    I_ _I_ _I Zone 38
    I_ _I_ _I Zone 39
    I_ _I_ _I Zone 40

1*02 Zone Types Zone 33 to 40
    I_ _I_ _I Zone 33
    I_ _I_ _I Zone 34
    I_ _I_ _I Zone 35
    I_ _I_ _I Zone 36
    I_ _I_ _I Zone 37

00 = Disabled
01 = Entry/Exit 1
02 = Entry/Exit 2
03 = Instant
04 = Interior
05 = Day Zone
06 = Holdup
07 = Police
08 = Medical
09 = Fire
10 = Interior/Delay
20 = Arm Stay
21 = Arm Away
22 = Disarm
23 = No Alarm Response
1*03 Zone Types Zone 41 to 48
    I_ _I_ _I Zone 41
    I_ _I_ _I Zone 42
    I_ _I_ _I Zone 43
    I_ _I_ _I Zone 44
    I_ _I_ _I Zone 45
    I_ _I_ _I Zone 46
    I_ _I_ _I Zone 47
    I_ _I_ _I Zone 48
1*04 Zone Types Zone 49 to 56
    I_ _I_ _I Zone 49
    I_ _I_ _I Zone 50
    I_ _I_ _I Zone 51
    I_ _I_ _I Zone 52
    I_ _I_ _I Zone 53
    I_ _I_ _I Zone 54
    I_ _I_ _I Zone 55
    I_ _I_ _I Zone 56

1*05 Zone Types Zone 57 to 64
    I_ _I_ _I Zone 57
    I_ _I_ _I Zone 58
    I_ _I_ _I Zone 59
    I_ _I_ _I Zone 60
    I_ _I_ _I Zone 61
    I_ _I_ _I Zone 62
    I_ _I_ _I Zone 63
    I_ _I_ _I Zone 64
1*06 Zone Types Zone 65 to 72
    I_ _I_ _I Zone 65
    I_ _I_ _I Zone 66
    I_ _I_ _I Zone 67
    I_ _I_ _I Zone 68
    I_ _I_ _I Zone 69
    I_ _I_ _I Zone 70
    I_ _I_ _I Zone 71
    I_ _I_ _I Zone 72

1*07 Zone Types Zone 73 to 80
    I_0_I_0_I Zone 73
    I_0_I_0_I Zone 74
    I_0_I_0_I Zone 75
    I_0_I_0_I Zone 76
    I_0_I_0_I Zone 77
    I_0_I_0_I Zone 78
    I_0_I_0_I Zone 79
    I_0_I_0_I Zone 80

1*08 Zone Types Zones 81 to 86 & Receiver & Voice Module Supervision
    I_0_I_0_I Zone 81
    I_0_I_0_I Zone 82
    I_0_I_0_I Zone 83
    I_0_I_0_I Zone 84
    I_0_I_0_I Zone 85
    I_0_I_0_I Zone 86
    I_0_I_0_I Zone 87 VIP Module Supervisory
    I_0_I_0_I Zone 88 2nd Receiver

1*09 1st & 2nd Receiver Troubles
    I_?_I_?_I Zone 89 2nd Receiver
    I_?_I_?_I Zone 90 1st Receiver
    I_?_I_?_I Zone 91 1st Receiver

1*17 Common Lobby Partition I_0_I 0 = Disabled
1 = Partition 1
to
8 = Partition 8

1*18 Affects Lobby I_0_I 0 = Does Not Affect Lobby (Partition-Specific)
1 = Affects Lobby

1*19 Arms Lobby I_0_I 0 = Does Not Arm Lobby (Partition-Specific)
1 = Arms Lobby

1*20 Exit Error Logic I_0_I 0 = No
1 = Bypass E/E & Interior Zones
faulted after Exit Delay

1*21 Exit Delay Reset I_0_I 0 = No
1 = Resets Exit Delay to 60 seconds
after Zone is Closed

1*22 Cross-Zoning Pair One I_ _I_ _I I_ _I_ _I

1*23 Cross-Zoning Pair Two I_ _I_ _I I_ _I_ _I

1*24 Cross-Zoning Pair Three I_ _I_ _I I_ _I_ _I

1*25 Cross-Zoning Pair Four I_ _I_ _I I_ _I_ _I

1*28 RF TX Low Battery Sound I_0_I 0 = When Disarmed
1 = Immediate

1*29 RF TX Low Batt Report I_0_I 0 = Disable
1 = Enable

1*30 RF RCVR Check-In Interval I_0_I_2_I 02 to 15 x2 Hours

1*31 RF xmitter Check-In I_0_I_2_I 02 to 15 x2 Hours

1*32 RF Receiver Type I_0_I 0 = None
2 = 5881

1*33 Tone with pulse Backup I_1_I 0 = Disable
1 = Enable

1*34 Comm Split Report I_0_I 0 = No
1 = Alarms to Primary, others Sec.
2 = O/C/Test Secondary, others Pri.
3 = Fire alarms/troubles Primary, all Sec.

(Use this section or #93 both does the same thing)


1*35 Alarm Report Codes Zone 65 to 72
    I_1_I_1_I Zone 65
    I_1_I_1_I Zone 66
    I_1_I_1_I Zone 67
    I_1_I_1_I Zone 68
    I_1_I_1_I Zone 69
    I_1_I_1_I Zone 70
    I_1_I_1_I Zone 71
    I_1_I_1_I Zone 72
1*36 Extended Report Codes Zone 65 to 72
    I_0_I_0_I Zone 65
    I_0_I_0_I Zone 66
    I_0_I_0_I Zone 67
    I_0_I_0_I Zone 68
    I_0_I_0_I Zone 69
    I_0_I_0_I Zone 70
    I_0_I_0_I Zone 71
    I_0_I_0_I Zone 72

1*37 Alarm Report Codes Zone 73 to 80
    I_1_I_1_I Zone 73
    I_1_I_1_I Zone 74
    I_1_I_1_I Zone 75
    I_1_I_1_I Zone 76
    I_1_I_1_I Zone 77
    I_1_I_1_I Zone 78
    I_1_I_1_I Zone 79
    I_1_I_1_I Zone 80
1*38 Extended Report Codes Zone 73 to 80
    I_0_I_0_I Zone 73
    I_0_I_0_I Zone 74
    I_0_I_0_I Zone 75
    I_0_I_0_I Zone 76
    I_0_I_0_I Zone 77
    I_0_I_0_I Zone 78
    I_0_I_0_I Zone 79
    I_0_I_0_I Zone 80

1*39 – Supervisory/Restore Zones 65 – 80
    I_0_I_0_I Alarm Restoral
    I_0_I_0_I Trouble
    I_0_I_0_I Trouble Restore
    I_0_I_0_I Bypass
    I_0_I_0_I Bypass Restore

1*40 – Non-Alarm Dialer Codes 1st Digit    
    I_0_I_0_I Armed Stay
    I_0_I_0_I Time Set/Event Log Reset
    I_0_I_0_I Event Log 50% & 90% Full
    I_0_I_0_I Event Log Overflow
    I_0_I_0_I Exit Error (Zone)
    I_0_I_0_I Exit Error (User)
    I_0_I_0_I Recent Close
1*41 – Non-Alarm Dialer Codes 2nd Digit
    I_0_I_0_I Armed Stay
    I_0_I_0_I Time Set/Event Log Reset
    I_0_I_0_I Event Log 50% & 90% Full
    I_0_I_0_I Event Log Overflow
    I_0_I_0_I Exit Error (Zone)
    I_0_I_0_I Exit Error (User)
    I_0_I_0_I Recent Close
1*42 Call Waiting Defeat I_0_I 0 = No
1 = Yes

1*43 Perm Keypad Backlight I_1_I 0 = No (Partition-Specific)
1 = Yes

1*44 Wireless Keypad Tamper I_0_I 0 = Disable
1 = Lockout RF if tamper detected

1*45 – Exit Delay Sounder I_0_I 1 = Enable (Partition-Specific)
0 = Disable

1*46 Auxiliary Output Mode I_0_I 0 = Ground Start
1 = O/C Trigger
2 = Console Sounding
3 = AAV

1*47 Chime on Siren I_0_I 0 = Disable (Partition-Specific)
1 = Enable

1*48 Wireless Keypad Part I_0_I 0 = Disable
1 = Partition 1
to
8 = Partition 8

1*49 Suppress TX sprvsn Sound I_1_I 0 = Enable
1 = Disable

1*52 Send Cancel I_0_I 0 = No Restriction (Partition-Specific)
1 = Within Bell Timeout

1*53 Download Callback I_1_I 0 = Callback Required
1 = No Callback

1*57 5800RF Global Arm I_0_I 0 = Disable
1 = Enable

1*58 5800RF Force Arm I_0_I 0 = Disable
1 = Enable

1*60 Zone 5 Audio Alarm I_0_I 0 = Disable
1 = Enable

1*70 Event Log Types I_1_I Alarm
I_1_I Check
I_1_I Bypass
I_1_I O/C
I_1_I System
0 = Disable Logging
1 = Enable Logging

1*71 Time Stamp Format I_1_I 0 = 12 Hour
1 = 24 Hour (Military)

1*72 Log Printer On-line Mode I_0_I 0 = Disable
1 = Enable

1*73 Printer Baud Rate I_0_I 0 = 1200 Baud
1 = 300 Baud

1*74 Relay Timeout XXX Min. I_0_I_0_I_0_I 0 to 127 x2 Minutes
Enter relay timeout desired for #80 Menu Mode
time-driven event relay command
numbers “04/09” and #93 Menu Mode
Output Programming output command “56.”

1*75 Relay Timeout YYY Sec. I_0_I_0_I_0_I 0 to 127 Seconds
Enter relay timeout desired for #80 Menu Mode
time-driven event relay command
numbers “05/10” and #93 Menu Mode
Output Programming output command “57.”

1*76 Access Control Relay I_0_I_0_I 00 to 96 (Partition-Specific)
Relay will be pulsed for 2 seconds
whenever code + [0] is pressed.


To access Upper programming press *94, to return to lower programming press *99
the 2 isn’t part of location, to go to a Upper program location press * + 2-digits

2*00 Number of Partitions I_1_I 1 = 1 Partition
to
8 = 8 Partitions

2*01 DST Start/End Month I_0_I_3_I I_1_I_1_I 00, 00 = Disable DST
Start End 01 – 12 = Month

2*02 DST Start/End Weekend
I_2_I
Start
I_1_I
End
1 to 7
1 = First
2 = Second
3 = Third
4 = Fourth
5 = Last
6 = Next to Last
7 = Third from Last

2*05 Auto-Arm Delay I_1_I_5_I 00 = Instant (Partition-Specific)
01 to 14 x4 Minutes
15 = No Auto-Arm

2*06 Auto-Arm Warning Period I_1_I_5_I 00 = Instant (Partition-Specific)
01 to 15 Minutes

2*07 Auto-Disarm Delay I_1_I_5_I 00 = Instant (Partition-Specific)
01 to 14 x4 Minutes
15 = No Auto-Disarm

2*08 Force Arm for Auto-Arm I_0_I 0 = Disable (Partition-Specific)
1 = Enable

2*09 O/C Reports by Exception I_0_I 0 = Disable (Partition-Specific)
1 = Enable

2*10 Disarming Only During
    Arming/Disarming Windows
I_0_I 0 = Disable (Partition-Specific)
1 = Enable

2*11 Disarming Outside
    Window
if Alarm Occurs
I_0_I 0 = Disable (Only used if 2*10 is a 1)
1 = Enable

2*13 – Scheduling related reports 1st Digit    
    I_0_I_0_I Early opening
    I_0_I_0_I Early closing
    I_0_I_0_I Late opening
    I_0_I_0_I Late closing
    I_0_I_0_I No opening (Late to open)
    I_0_I_0_I No closing (Late to close)
    I_0_I_0_I Auto-arm failure
    I_0_I_0_I Access schedule changed
2*14 – Scheduling related reports 2nd Digit
    I_0_I_0_I Early opening
    I_0_I_0_I Early closing
    I_0_I_0_I Late opening
    I_0_I_0_I Late closing
    I_0_I_0_I No opening (Late to open)
    I_0_I_0_I No closing (Late to close)
    I_0_I_0_I Auto-arm failure
    I_0_I_0_I Access schedule changed
2*18 Enable Go To for Partition I_0_I 0 = Disable (Partition-Specific)
1 = Enable

2*19 Use Partition Descriptors I_0_I 0 = Disable
1 = Enable

2*20 Enable J2 Triggers Partn I_0_I 0 = Disable (Partition-Specific)
1 = Enable

2*21 Enable Supervsn Pulses
For LRR Trigger Outputs
I_0_I Fire
I_0_I Burglary
I_0_I Silent panic/Duress
0 = Disable
1 = Enable