Ademco Vista 21ip Sensors

Home
Ademco
Ademco Vista
Ademco Vista

Ademco Vista 21IP Sensors

Ademco 5816 Door / Window	Ademco 5802 Panic
Ademco 5745 Glassbreak	Ademco 5806 Smoke
Ademco 5849 Glassbreak	Ademco 5807 Smoke
Ademco 5850 Glassbreak	Ademco 5808 Smoke
Ademco 5801 Keyfob / Panic	Ademco 5817 Transmitter
Ademco 5804 Keyfob	Ademco 5819 Transmitter
Ademco 5827 Keypad	Ademco 5804 Watch-Keyfob
Ademco 5827BD Keypad	Ademco 5881 Wireless Receiver
Ademco 5890 Motion

Ademco 5816 Door / Window

Ademco 5745 / 5845 Glassbreak

Ademco 5849 Glassbreak

Ademco 5850 (Intellisense) Glassbreak

Ademco 5801 Keyfob / Panic

Ademco 5804 Keyfob


Zone Types	21=Arm-Away	22=Disarm
	20=Arm-Stay	07=24 Hr Police
		06= 24 Hr Silent Police

Ademco 5827 Keypad

Remove battery when changing switches!

Note: older versions will work with 5700 wireless systems, new versions do not.

House ID	Dip Switch					House ID	Dip Switch
	1	2	3	4	5		1	2	3	4	5
1	dn	dn	dn	dn	UP	16	UP	dn	dn	dn	dn
2	dn	dn	dn	UP	dn	17	UP	dn	dn	dn	UP
3	dn	dn	dn	UP	UP	18	UP	dn	dn	UP	dn
4	dn	dn	UP	dn	dn	19	UP	dn	dn	UP	UP
5	dn	dn	UP	dn	UP	20	UP	dn	UP	dn	dn
6	dn	dn	UP	UP	dn	21	UP	dn	UP	dn	UP
7	dn	dn	UP	UP	UP	22	UP	dn	UP	UP	dn
8	dn	UP	dn	dn	dn	23	UP	dn	UP	UP	UP
9	dn	UP	dn	dn	UP	24	UP	UP	dn	dn	dn
10	dn	UP	dn	UP	dn	25	UP	UP	dn	dn	UP
11	dn	UP	dn	UP	UP	26	UP	UP	dn	UP	dn
12	dn	UP	UP	dn	dn	27	UP	UP	dn	UP	UP
13	dn	UP	UP	dn	UP	28	UP	UP	UP	dn	dn
14	dn	UP	UP	UP	dn	29	UP	UP	UP	dn	UP
15	dn	UP	UP	UP	UP	30	UP	UP	UP	UP	dn
						31	UP	UP	UP	UP	UP

Ademco 5827BD Keypad

Requires 5800TM Transmitter Module
If using 5128RF keypad the 5800TM module is not needed
If using 5881 or 5882 receiver the 5800TM is needed
Panel Programming	1. Enter RF System type in 22 (1 = 5700 2= 5800) 2. Enter House Code in 24 (01 – 31)
Keypad Programming	1. Press * (Yellow light starts blinking) 2. Hold 1 and 3 for 3 seconds (Red & Green Lights start blinking) 3. * 8 + Master Code + # (Enters Master Code) 4. * 1 + Master Code + # (Enables Quick Arm) 5. * 9 + House Code + # 6. * 57 + # if using 5700 Receiver * 58 + # if 5800 7. * + # exits programming

Ademco 5890 Motion

Ademco 5802 Panic

Ademco 5806 Smoke

Ademco 5807 Smoke

Ademco 5808 Smoke

Ademco 5817 Transmitter

Ademco 5819 Transmitter

Ademco 5804 Watch

Works ONLY with 5881EN Encrypted Receivers, will not work on older receivers or Lynx

Serial number on bottom sticker of watch, make sure tech writes it down in panel as a backup if lost

Operation Press Red SECURITY button then press function desired

Program

1. Hold Red SECURITY button for 8 seconds, Loop 1 programming begins

(This shows Loop 1 is disabled)

2. Press START/STOP to cycle through available commands (see list at bottom)

(This shows Loop 1 is set for AWAY Arming)

3. Press MODE to save selected command and move to next

4. Some commands support a delay from 0 to 15 seconds, cycle selections with

START/STOP then press MODE to save and move to Loop 2

(This shows Loop 1 is set for no sending delay)

5. After programming all 4 loops display will show message duration, this is time in
seconds signal will send, press START/STOP to cycle selections then MODE to save
(bad areas may need longer time to send, good areas less)

(This shows send duration of 8 seconds)

6. Press Red SECURITY button to exit programming

Available Commands\|	How it displays on watch	\|Delay available?
NONE (Disabled)	NONE	No
AWAY	AWY	Yes
STAY	STY	Yes
ON	ON	Yes
OFF (Disarm)	OFF	Yes
Panic (General)	PAN	No
Police Panic	POL	No
Medical Panic	MED	No
Fire Panic	FIR	No
Lock*	LOK	Yes
Unlock*	UNL	Yes
Light*	LIT	Yes
Door (Access)	DOR	Yes
Accessory*	ACC	Yes

*sorry don’t know what these commands do yet

Ademco 5881 Wireless Receiver

Available in Low (8 zones), Medium (16 zones) and High (up to 64 zones)