Ademco Vista 21ip Program

Ademco Vista 21IP Programming

This is a version of the Vista-20p [ 4-Wire Smoke ] [ Device Address Table ] [ E-Secure Programming ]
AVS 2-Way Module	Note: Do this outside of Programming (V7 or highder) Installer code + [#] + 03: Enable AVS operation without panel sounds on the AVST Installer code + [#] + 04: Enable AVS operation and enable panel sounds on AVST Installer code + [#] + 05: Disable AVS operation without panel sounds on the AVST Installer code + [#] + 06: Disable AVS operation and enable panel sounds on AVST
Enter Program	4112 + 8 + 0 + 0 (Display should show 20) or Power down then back up and press * and # within 1 minute (If exiting programming you can re-enter within 1 minute by pressing * and #)
Move to Location	* + Location
View Location	# + Location (Display will read off one digit at a time)
Exit Program	98 OR 99 if needing to re-enter programming later by Code + 8 + 00
Timer Test	Installer code + # + 00= Daily Installer code + # + 01= weekly Installer code + # + 02= Monthly * 64 Test Report code I_1_I_0_I

*20

Installer Code

I_4_I_1_I_1_I_2_I

*21

Quick Arm Enable

I_1_I

0 = No 1 = Yes

*22

RF Jam Option

I_0_I

0 = None 1 = send RF Jam report

*23

Forced Bypass Enable

I_0_I

0 = No 1 = Yes

*24

RF House Code

I_0_I_0_I Part 1
I_0_I_0_I Part 2
I_0_I_0_I Common

00 = Disabled

*26

Chime by Zone

I_0_I_0_I

(Entry 1)

0 = Disabled

1 = Enabled

2 = Comm Device Trouble Sounding

4 = System Low Bat Sounding

7 Select all Entry 1 Options

(Entry 2)

0 = Disabled

1 = TF Supervision Sounding Enabled

2 = RF Low Battery Sounding Enabled

4 = RF Jam Sounding Enabled

7 Select all Entry 2 Options

*27

X-10 House Code

I_0_I

0 = A 1 = B 2 = C 3 = D 4 = E 5 = F
6 = G 7 = H 8 = I 9 = J #10 = K #11 = L
#12 = M #13 = N #14 = O #15 = P

*28

4285/4286
Voice Module Access Code

I_0_I_0_I

(Allows access to Voice module)
00 = Disabled
1st digit = 1 to 9
2nd digit = # + 11 for * or # + 12 for #

*29

[ Menu Mode for IP/GSM Enable ]

*31

Single Alarm Sounding/Zone

I_0_I

0 = No (If 0, follows swinger suppression in *93)
1 = Yes

*32

Fire Sounder Timeout

I_1_I

0 = Timeout
1 = No Timeout

*33

Alarm Bell Timeout

I_2_I

0 = None
1 = 4 minutes
2 = 8 minutes
3 = 12 minutes
4 = 16 minutes

*34

Exit Delay

I_6_I_0_I part 1
I_6_I_0_I part 2

45 – 96 = 45 – 96 Seconds
97 = 120 Seconds
NOTE: Entries less than 45 seconds will result in a 45 second delay

*35

Entry Delay #1 (Zone type 01)

I_3_I_0_I part 1
I_3_I_0_I part 2

30 – 96 = 30 – 96 Seconds
97 = 120 Seconds
98 = 180 Seconds
99 = 240 Seconds

*36

Entry Delay #2 (Zone type 02)

I_6_I_0_I part 1
I_6_I_0_I part 2

*37

Audible Exit Warning

I_N/A_I

Feature always enabled. Cannot be disabled

*38

Confirmation of Arming Ding

I_0_I part 1
I_0_I part 2

0 = No
1 = Yes
2 = RF Only

*39

Power Up in Previous State

I_0_I

0 = No 1 = Yes

*40

PABX Access Code
(Up to 6 digits)

I_ _I_ _I_ _I_ _I_ _I_ _I (If 9 is needed to dial add here)

*41

Primary Phone
(Up to 20 digits)

I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
End Phone with *
# + 11 = *# + 12 = # # + 13 = 2 second pause

*42

Secondary Phone
(Up to 20 digits)

I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
End Phone with *
# + 11 = *# + 12 = # # + 13 = 2 second pause

*43

Partition 1 Primary Account #

I_ _I_ _I_ _I_ _I (Last 4 of Account)
A = # + 10 B = # + 11 C = # + 12 D = # + 13 E = # + 14 F = # + 15

*44

Partition 1 Secondary Account #

I_ _I_ _I_ _I_ _I

*45

Partition 2 Primary Account #

I_ _I_ _I_ _I_ _I (Last 4 of Account)
A = # + 10 B = # + 11 C = # + 12 D = # + 13 E = # + 14 F = # + 15

*46

Partition 2 Secondary Account #

I_ _I_ _I_ _I_ _I

*47

Phone System Select

I_3_I

0 = Pulse Dial
1 = DTMF Dial
2 = Pulse Dial, CS on Watts Line
3 = DTMF Dial, CS on Watts Line

*48

Report Format

I_07_I Primary
I_07_I Secondary

00 = 3/1, 4/1 Ademco L/S Standard
01 = 3/1, 4/1 Radionics Standard
02 = 4/2 Ademco L/S Standard
03 = 4/2 Radionics Standard
05 = 10-digit Contact ID
06 = 4/2 Ademco Express
07 = Contact ID
08 = 3/1, 4/1 Ademco L/S Expanded
09 = 3/1, 4/1 Radionics Expanded

*49

Split/Dual Reporting

I_0_I

To Primary Phone To	Secondary Phone
0 = All Reports	Backup Only
1 = Alarms, Restore, Cancel	All Other Reports
2 = All Reports except O/C, Test	Open/Close, Test
3 = Alarms, Restore, Cancel	All Reports
4 = All Reports except O/C, Test	All Reports
5 = All Reports (Dual Reporting)	All Reports

*50

Burg Dialer Delay

I_2_II_0_I

Delay Time: 1 = 15 secs; 2 = 30 secs; 3 = 45 secs
Delay Disable: 0 = use delay set in 1st digit
1 = dial delay disabled for zones listed in zone list 6
(Use zone list 6 to enter zones that need dial delay
to be disabled; these zones ignore the setting in entry 1)

*53

Sescoa/Radionics

I_0_I

0 = No
1 = Yes

*54

Dynamic Signaling Delay

I_0_I

0 = No delay (Both signals sent)
1 = 15 seconds
2 = 30 seconds (etc)

*55

Dynamic Signaling Priority

I_0_I

0 = Primary Dialer First (Alarmnet is secondary)
1 = Long Range Radio First (Alarmnet is primary)

*56

Zone Assignments

Hardwired

Zones 01 to (2-Wire Smokes Zone 1 only, 4-Wire can be 2 to 8)

4219/4229
Hardwire Expander

Zones 09 to 16 or Zones 17 to 24

Wireless

Zones 09 to 48 (Depending on capacity of 5881 receiver)

Keyfob Zones

Zones 49 to 56

Duress

Zone 92

Fire Panic

Zone 95

Medical Panic

Zone 96

Police Panic

Zone 99

1. Keypad displays “Zone Prog?” press 1

2. “Enter Zn No.” enter which zone to program (01-56, 89-91, 95, 96, 97, 99) press *

3. Keypad will show summary zones programming, press *

4. “Zone Type?”
Enter type then *

00 = Zone Disabled/Deleted
01 = Delay Zone
02 = Secondary Delay Zone
03 = Perimeter/Instant
04 = Interior Follower/Motions
05 = Trouble by Day/Alarm by Night
06 = 24 hour Silent/Holdup
07 = 24 hour Police Panic
08 = 24 hour Aux/Medical
09 = Fire
10 = Interior Delay
12 = Monitor Zone
14 = Carbon Monoxide
16 = Fire w/Verification
20 = Arm-Stay (RF only)
21 = Arm-Away (RF only)
22 = Disarm (RF only)
23 = No Alarm Response
24 = Silent Burglary
77 = Keyswitch
81 = AAV Monitor
90 = Configurable Zone Type 1 * See section * 182
91 = Configurable Zone Type 2 * See section * 184

6. “Report Code?”
enter 10 then *

7. “Input Device?”
Enter device then *

01 = for Hardwired
02 = Auxiliary Wired (with 4219/4229 Expander)
03 = for Supervised RF (most sensors are RF)
04 = for Un-Supervised RF
05 = RF Button Type (Keyfobs/Panics etc)

8. Cursor should flash above the loop number “LP#”, Enter 1 to 4 depending on sensor

Door Switch

Loop 1 = External Sensor Connector
Loop 2 = Internal Reed Switch

Glassbreak

Loop 1

Smoke Detectors

Loop 1

Motions

Loop 1

Keyfobs

Loop 1 = Bottom Right Button (Each button counts as 1 zone)
Loop 2 = Top Right Button
Loop 3 = Top Left Button
Loop 4 = Bottom Left Button

9. “Learn Sensor Y/N?”

Press 1 and trip sensor twice (you cannot enter serial numbers)

10. “Alpha Program?”

Press 0 if not programming – [ Alpha Descriptors ]

11. “Keypad will show either new summary for zone or “Enter zone number”

12. If finished programming enter 00 at “Enter zone no” to return to normal programming

*57

[ Function Key Programming ] – (6139 or 6160 Alpha Keypad required here)

(If altering function keys A B or C delete programming for zones 95, 99 or 96)

Defaults

Function Key A Zone 95

Function Key B Zone 99

Function Key C Zone 96

Function Key D Single Button Page

1. Press Function Key to program

(A = Top to D = Bottom Function Key)

2. Display shows Function Key chosen

(* for next, # for previous menu)

3. Enter Partition of Function Key

(* for next, # for previous menu)

1 = Partition 1

2 = Partition 2

3 = Common Partition (Lobby)

4. Choose Function for this Key

(* for next, # for previous menu)

00 = A Zone
95 B = Zone
99 C = Zone
96 D = Single Button Page

01 = Single Button Page (sends 999-9999 message to Pager
02 = Display Time
03 = Arm Away
04 = Arm Stay
05 = Arm Night/Stay (any Zone in Zone List 5 *81 menu)
06 = Step Arming (Stay then Night/Stay then Away)
07 = Device A Activation (Type 66 Function in *80 menu)
08 = Communication Test
09 = Macro Key 1 (Activated by User Code + # + 66)
10 = Macro Key 2 (Activated by User Code + # + 66)
11 = Macro Key 3 (Activated by User Code + # + 66)
12 = Macro Key 4 (Activated by User Code + # + 66)

5. Enter next Function Key or 0 to exit

6. Press * or # to exit

*58

Expert Mode

Programming keys:

A – Right	B – Left	C – Copy last	D – Keyfob Template
(in field)	(in filed)	(zone config)	[ Click Here ]

1. “Set to confirm?”

0 = No, 1 = Yes

2. Summary of zone 1’s current programming. Enter 2-digit zone number and press *, 00 to quit

Zn	ZT	P	RC	HW	RT
01	03	1	10	EL	1

Zn	ZT	P	RC	IN	L
10	03	1	10	RF	1

Enter zone information and then * for next (A moves right, B moves left)

ZT = Zone Type

P = Partition

RC = Report Code

IN = Input Device Type (Zones 1-8 has HW instead and should be EL)

L = Loop number (Zones 1-8 has RT instead and should be 1)

3. If wireless goes to enter S/N if hardwired goes to the next zone

*59

Exit Error Report Code

I_1_I

SIA NOTE: Always enabled.

*60

Trouble Report Code

I_1_I_0_I

*61

Bypass Report Code

I_0_I_0_I

*62

AC Loss Report Code

I_1_I_0_I

*63

Low Bat Report Code

I_1_I_0_I

*64

Test Report Code

I_0_I_0_I

(Installer code + # + 0 + 2
outside programming to enable monthly)

*65

Open Report Code

I_0_I	I_0_I	I_0_I
Part 1	Part 2	Common

*66

Away/Stay Report

I_0_I_0_I	I_0_I_0_I	I_0_I_0_I
Partition 1	Partition 2	Common

*67

RF Xmtr Low Bat

I_0_I_0_I

*68

Cancel Report Code

I_1_I_0_I

*69

Recent Close

I_1_I

SIA NOTE: Always enabled.

*70

Alarm Restore Code

I_0_I

(Must be enabled if using smoke)

*71

Trouble Restore Code

I_0_I_0_I

*72

Bypass Restore Code

I_0_I_0_I

*73

AC Restore Code

I_0_I_0_I

*74

Low Bat Rest Code

I_0_I_0_I

*75

RF Low Bat Rest Code

I_0_I_0_I

*76

Test Restore Rpt Code

I_0_I_0_I

*77

Daylight Sav Time
Start/End Month

I_3_I_11_I

0 = Disabled
1 – 9 = January – September (1 = Jan, 2 = Feb, etc)
#10 = October, #11 = November, #12 = December

*78

Daylight Sav Time
Start/End Weekend

I_2_I_1_I

0 = Disabled
1 = First
2 = Second
3 = Third
4 = Fourth
5 = Last
6 = Next to last
7 = Third to last

*79

Output Device Mapping – [ Relay Programming ]

*80

Output Programming – [ Relay Programming ]

*81

Zone List Programming

*82

Alpha Editing (Same as in *56) – [ Alpha Descriptors ]

*84

Auto Stay Arm

I_0_I

0 = Disabled,
1 = Part 1 only,
2 = Part 2 only,
3 = both

*85

Cross Zone Timer

I_0_I

0 = 15 seconds	6 = 2 min	# + 11 = 7 min
1 = 30 seconds	7 = 3 min	# + 12 = 8 min
2 = 45 seconds	8 = 4 min	# + 13 = 10 min
3 = 60 seconds	9 = 5 min	# + 14 = 12 min
4 = 90 seconds	# + 10 = 6 min	# + 15 = 15 min
5 = 2 minutes

*86

Cancel Verify Keypad Display

I_0_I

0 = No “alarm cancelled” display
1 = Displays “alarm cancelled” when code + off is pressed

*87

Misc. Fault Delay Time

I_0_I

0 = 15 seconds	6 = 2 min	# + 11 = 7 min
1 = 30 seconds	7 = 3 min	# + 12 = 8 min
2 = 45 seconds	8 = 4 min	# + 13 = 10 min
3 = 60 seconds	9 = 5 min	# + 14 = 12 min
4 = 90 seconds	# + 10 = 6 min	# + 15 = 15 min
5 = 2 minutes

*88

Program Mode Lockout Option

I_0_I

0 =	Standard 98 lock out w re-entry by [] + [#]
1 =	Disables [*] + [#] to enter program after power up; Only Installer code and/or downloading will allow access.
2 =	Not used
3 =	Lockout local programming. Must download to re-enter programming

*89

Event Log 80% Full

I_0_I_0_I

*90

Event Logging

I_15_I

0 = None
1 = Alarm/Restore
2 = Trouble/Restore
4 = Bypass/Bypass Restore
8 = Open/Close

*91

Option Selection

I_0_I I_0_I

0 = None
Options Call Waiting Disable 4 = AAV
8 = Exit Delay Restart

*92

Phone Monitor Enable

I_0_I

(Panel MUST be properly grounded for this to work!)
0 = Not Used
1 = KP Disp
2 = KP Disp/Sounder
3 = KP Disp/Sounder/Dev 2 starts

*93

Reports per Armed Period
Per Zone

I_0_I

0 = Unlimited Reports per Armed period
1 = 1 report pair per armed period
2 = 2 report pairs per armed period

*94

Download Phone Number

I_1_I_8_I_0_I_0_I_5_I_6_I_0_I_2_I_0_I_0_I_1_I_ _I

*95

Ring Count

I_#15_I

0 to #15 #15 = Answer Machine Defeat

*96

Reinitialize Download (No Value needed, keypad will just beep and resets CSID and Account number to F’s)

*97

Default Panel (No Value needed, keypad will beep and default panel)

*98

Exits Program Mode (Will not allow re-entry with Installer Code + 8 + 0 + 0)

*99

Exits Program Mode (Will allow re-entry with Code + 8 + 0 + 0)

*160

Pager 1 Phone No.

I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
(Enter up to 20 digits. 0-9; # + 11 = ‘*’; # + 12 = ‘#’; # + 13 = 2 second pause)

*161

Pager 1 Characters

I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
(Enter the optional additional prefix characters up to 16 digits
0-9; # + 11 = ‘*’; # + 12 = ‘#’; # + 13 = 2 second pause)

*162

Pager 1 Reporting Options

_0_

Com

Select from the following options:

0	= No reports sent
1	= Open/closes all users
4	= All alarms and troubles
5	= All alarms / troubles, and o/c for all users
12	= Alarms / troubles for zones in zone list 9
13	= Alarms / troubles for zones in zone list 9, and open/closes for all users

*163

Pager 2 Phone No.

I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
(Enter up to 20 digits. 0-9; # + 11 = ‘*’; # + 12 = ‘#’; # + 13 = 2 second pause)

*164

Pager 2 Characters

I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
(Enter the optional additional prefix characters up to 16 digits
0-9; # + 11 = ‘*’; # + 12 = ‘#’; # + 13 = 2 second pause)

*165

Pager 2 Reporting Options

_0_

Com

Select from the following options:

0	= No reports sent
1	= Open/closes all users
4	= All alarms and troubles
5	= All alarms / troubles, and o/c for all users
12	= Alarms / troubles for zones in zone list 9
13	= Alarms / troubles for zones in zone list 9, and open/closes for all users

*166

Pager 3 Phone No.

I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
(Enter up to 20 digits. 0-9; # + 11 = ‘*’; # + 12 = ‘#’; # + 13 = 2 second pause)

*167

Pager 3 Characters

I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
(Enter the optional additional prefix characters up to 16 digits
0-9; # + 11 = ‘*’; # + 12 = ‘#’; # + 13 = 2 second pause)

*168

Pager 3 Reporting Options

_0_

Com

Select from the following options:

0	= No reports sent
1	= Open/closes all users
4	= All alarms and troubles
5	= All alarms / troubles, and o/c for all users
12	= Alarms / troubles for zones in zone list 9
13	= Alarms / troubles for zones in zone list 9, and open/closes for all users

*169

Pager 4 Phone No.

I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
(Enter up to 20 digits. 0-9; # + 11 = ‘*’; # + 12 = ‘#’; # + 13 = 2 second pause)

*170

Pager 4 Characters

I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
(Enter the optional additional prefix characters up to 16 digits
0-9; # + 11 = ‘*’; # + 12 = ‘#’; # + 13 = 2 second pause)

*171

Pager 4 Reporting Options

_0_

Com

Select from the following options:

0	= No reports sent
1	= Open/closes all users
4	= All alarms and troubles
5	= All alarms / troubles, and o/c for all users
12	= Alarms / troubles for zones in zone list 9
13	= Alarms / troubles for zones in zone list 9, and open/closes for all users

*172

Pager Delay Option For Alarms

I_0_I

0 = none, 1 = 1 minute, 2 = 2 minutes, 3 = 3 minutes
This delay is for ALL pagers in the system.
NOTE: Delay does not reset for new alarms occurring
while an existing pager delay is in progress.

*174

Clean Me Reporting Option
(For ESL smoke detectors)

I_0_I

0 = disable; 1 = Clean Me signal reports;
Note: If Clean Me is enabled, you must enter “3”
in field *56 programming for zone 1 response time.

*177

Device Duration 1, 2

I_0_I	I_0_I
1	2

(Used in *80 Menu mode device action 5/6)

0 = 15 seconds

6 = 2 min

# + 11 = 7 min

1 = 30 seconds

7 = 3 min

# + 12 = 8 min

2 = 45 seconds

8 = 4 min

# + 13 = 10 min

3 = 60 seconds

9 = 5 min

# + 14 = 12 min

4 = 90 seconds

# + 10 = 6 min

# + 15 = 15 min

5 = 2 minutes

*181

50/60 Hertz AC Operation

I_0_I

0 = 60 Hz; 1 = 50 Hz

*182

Configurable Zone Type 90

I_0_I	I_0_I	I_0_I	I_0_I	I_0_I	I_0_I	I_0_I	I_0_I	I_0_I	I_0_I
1	2	3	4	5	6	7	8	9	10

[ Zone Types ]

Enter the appropriate Value for each entry, 1-10, based on the links.
Each entry is the sum of the values on its selected options.
(0-9; # + 10 = 10, # = 11 = 11, # + 12 = 12, # + 13 = 13, # + 14 = 14, # + 15 = 15)

*183

Zone Type 90 Report Codes (IMPORTANT: Use Existing CID Codes, if appropriate, or define Unique codes in CID code range 750-789.)

90 ALARM ID: XXX

TROUBLE ID: XXX

Enter the desired 3 digit CID report codes for alarms and troubles occurring on zones assigned to this zone type. Enter the codes sequentially (all 6 digits). When entering digits, [#] moves cursor back, [*] moves forward. Press [*] when done to continue.

*184

Configurable Zone Type 91

I_0_I	I_0_I	I_0_I	I_0_I	I_0_I	I_0_I	I_0_I	I_0_I	I_0_I	I_0_I
1	2	3	4	5	6	7	8	9	10

[ Zone Types ]

*185

Zone Type 91 Report Codes (IMPORTANT: Use Existing CID Codes, if appropriate, or define Unique codes in CID code range 750-789.)

91 ALARM ID: XXX

TROUBLE ID: XXX

*189

AUI Device Enables

I_0_I
AUI 1

I_0_I
AUI 2

I_0_I
AUI 3

I_0_I
AUI 4

For Touch Screen style keypads

0 = Disable	AUI 1 = ECP Address 1
1 = Partition 1	AUI 2 = ECP Address 2
2 = Partition 2	AUI 3 = ECP Address 5
3 = Common	AUI 4 = ECP Address 6

*190

Keypad 2 Device Address 17

I_0_I I_0_I

1st digit Partition:

0 = Keypad disabled;
1 = Partition 1 enable;
2 = Partition 2, etc.

2nd digit Sound:

0 = no suppression
1 = suppress arm/disarm and E/E beeps
2 = suppress chime beeps only
3 = suppress arm/disarm, E/E, and chime beeps

*191

Keypad 3 Device Address 18

I_0_I I_0_I

See field *190 for entries.

*192

Keypad 3 Device Address 19

I_0_I I_0_I

See field *190 for entries.

*193

Keypad 3 Device Address 20

I_0_I I_0_I

See field *190 for entries.

*194

Keypad 3 Device Address 21

I_0_I I_0_I

See field *190 for entries.

*195

Keypad 3 Device Address 22

I_0_I I_0_I

See field *190 for entries.

*196

Keypad 3 Device Address 23

I_0_I I_0_I

See field *190 for entries.

*197

Exit Time Display Interval

I_0_I

0 = no display; 1-5 = sec between display Refresh

*198

Display Partition Number

I_0_I

For Alpha Displays Only
0 = No
1 = Yes (Partition # will display on Alpha Display)

*199

ECP Fail Display

I_0_I

0 = 3-digit display (“1” + device address)
1 = 2-digit fixed display as “91”

Programming	Program the zone for FIRE (Type 09)
	Program the zone for FIRE (Type 09)
	In *79 Menu Mode, program Output 17 for “Out Norm Low” = Yes
	In 80 Menu Mode, program as follows: Output Function – Next Available (01 if none are programmed), then press Summary Display – Press * Activated By – 2 (Zone Type), then press * Zone Type – 54 (Fire Zone Reset), then press * Output # – 17 (On-Board Trigger 1), then press * Summary Display – press * 00 to quit *80 Menu Mode
Wiring	Connect the NEGATIVE lead from the smoke detector power circuit to Output 17
	Connect the POSITIVE lead from the smoke detector power circuit to Terminal 5
	(+ Aux. Power) on the 300P-1 board or pin 3 on the 8-pin connector
	Connect the leads from the smoke setector zone circuit to any of the hardwire
	Will not work on zone 1 on panels 320p or lower
	Connect the EOL resistor across alarm terminal of the last smoke detector
(EOL Realy required in TX: Connect the EOL resistor from one alarm terminal of the last smoke detector to a violet wire on the EOL relay, as shown in Figure 1. Connect the other violet wire to the other alarm terminal. Connect the red and black wires from the EOL Relay to the [+] and [-] terminals of the smoke detector.)

Device	Uses Address	Reports As‡	Enabled By
RF Receiver	0	100	*56 Zone Programming: Enabling a wireless zone
AUI 1††	1	101	Automatic if AUI enable field *189 enabled AUI 1
AUI 2††	2	102	Automatic if AUI enable field *189 enabled AUI 2
Long Range Radio	3	103	Automatic if *29 is enabled
4286 Voice Module	4	104	Automatic if *28 has an entry
AUI 3‡‡	5	105	Automatic if AUI enable field *189 enabled AUI 3
AUI 4‡‡	6	106	Automatic if AUI enable field *189 enabled AUI 4
4219/4229			*56 Zone Programming: Enabling zone as AW type or realy assigned
Module 1	7**	107	*56 Zone Programming: Enabling zone 9-16 as AW type or realy assigned
Module 2	8	108	*56 Zone Programming: Enabling zone 17-24 as AW type or realy assigned
Module 3	9†	109	*56 Zone Programming: Enabling zone 25-32 as AW type or realy assigned
Module 4	10†	110	*56 Zone Programming: Enabling zone 33-40 as AW type or realy assigned
Module 5	11†	111	*56 Zone Programming: Enabling zone 41-48 as AW type or realy assigned
4204			*79 Output device programming: Device address prompt
Module 1	12	112	*79 Entered in device address prompt
Module 2	13	113	*79 Entered in device address prompt
Module 3	14†	114	*79 Entered in device address prompt
Module 4	15†	115	*79 Entered in device address prompt
Keypads			Data Field programming as listed below:
Keypad 1	16	n/a	Always enabled for partition 1, all sounds enabled
Keypad 2	17	n/a	*190
Keypad 3	18	n/a	*191
Keypad 4	19	n/a	*192
Keypad 5	20	n/a	*193
Keypad 6	21	n/a	*194
Keypad 7	22	n/a	*195
Keypad 8	23	n/a	*196
5800TM	28	n/a	Automatic

Enable IP/GSM	0 = Disabled 1 = Enabled
Programming/ Diagnostics select	1 = Prog 2 = Diag 3 = Quit
Internal Device Selection	Disable, IP, GSM, IP & GSM Select the desired type by pressing * to scroll and # to continue
Multi-Mode (email reporting)	Disable, 4204 sourced, 2-4204 sourced, enhanced reports
Multi-mode address	12-15= emulated 4204 relay module address, 25 auto assigned if Enhance reports is selected.
Primary City ID	01-99
Primary CS ID	01-FE (HEX)
Primary Sub ID	0001-9999
Remote Access	Y= use remove services	N= do not use remote services
Keypad address	[1,2,5,6]= emulated AUI address	17-23 emulated standard keypad address
Supervision	[IP and/or GSM]= 30 days, 24 hrs, none [IP only]= US UL 6 min or 90 sec, CN UL 3 min, 90 sec, 75 sec 1 hour
GSM Rollover	Y, N
GSM 24 hr test	Y, N
Old Alarm Time	10 mins, 15 mins, 30 mins, 1 hour, 2 hours, 4 hours, 8 hours, 12 hours, 24 hours
IP fault time	00-99
GSM Flt Time	00-99
Notify Panel of:	Neither Fault, Both IP and GSM
NIC IP Address	Enter the 4=part IP address for this device, separating each part with a space, use * as periods
Subnet Mask	Enter in subnet mask
Gateway IP Address	Enter the 4=part IP address for this device, separating each part with a space, if unused set to 0.0.0.0, use * as periods
DSN IP Address	Enter in DNS IP, use * as periods
Review	Y= will allow to look at all the settings, N=exit menu mode

Ademco Vista 21IP Programming

4-Wire Smoke

Device Address Table

E-Secure Programming

Alpha Descriptors

Function Key Programming

Expert Template Mode

Programming 4204 / 4229 Relays

Configurable Zone Types

Menu Mode for IP/GSM Enable

ESECURE 1.0
*79	Relay	Type	Address	Position No
	I_9_I	I_1_I	I_14_I	I_1_I
	I_10_I	I_1_I	I_14_I	I_2_I
	I_11_I	I_1_I	I_14_I	I_3_I
	I_12_I	I_1_I	I_14_I	I_4_I
*80	Relay	Trigger	Zone Type	Partition	Action	Output
	I_31_I	I_2_I	I_31_I	I_1_I	I_2_I	I_09_I
	I_32_I	I_2_I	I_22_I	I_1_I	I_0_I	I_09_I
	I_33_I	I_2_I	I_41_I	I_0_I	I_4_I	I_10_I
*189	I_1_I_0_I_0_I_0_I
ESECURE 2.0
*29	I_1_I
*91	I_8_I I_2_I
*189	I_5_I I_1_I I_1_I I_1_I