1. Home
  2. Ademco
  3. Ademco Via
  4. Ademco Via
Enter Program Master Code + 8 + 0 + 0 (Display should show 20)
or Power down then back up and press * and # within 1 minute
(If exiting programming you can re-enter within 1 minute by pressing * and #)
Move to Location * + Location
View Location # + Location (Display will read off one digit at a time)
Exit Program 1. *98 OR 2. *99 if needing to re-enter programming later by Code + 8 + 00
Test Timer *49 Periodic Test I_3_I 1=24 hrs 2= Weekly 3= Monthly
*64 Test Report Code I_1_I_0_I
*20 Master Code I_4_I_1_I_1_I_1_I
*21 Quick Arm Enable I_1_I 0 = No
1 = Yes
*22 RF System Type I_2_I 0=None
Panel treats 5700 wireless as hardwire 1=5700 wireless receiver (Old stuff)
4281L receiver adds 4 zones 2=5800 wireless receiver
4281M and 4281H add 8 zones
*23 Force Bypass Enable I_0_I 0 = No
1 = Yes
*24 RF House Code I_0_I_0_I 00 = Disabled, 01 to 31
Used only with 5700 series wireless, 5804BD keyfob and 5827BD Keypad
*25 Wired Expansion/Relay I_0_I 0 = None
1 = 4219 8-Zone Expander
2 = 4229 8-Zone Exp Relay
3 = 4204 Relay Module
*26 4284/4285 Voice Module Code I_0_I_0_I 00 = Disabled
1st digit = 1 to 9
2nd digit = # + 11 = * or # + 12 = #
*27 Output to Long Range Radio I_0_I 0 = No
1 = Yes
*28 Single Alarm Sound/Zone I_0_I 0 = No
1 = Yes
*29 Fire Sounder Timeout I_1_I 0 = Yes
1 = No Fire Timeout
*30 Alarm Bell Timeout I_2_I 0 = None
1 = 4 minutesa
2 = 8 minutes
3 = 12 minutes
4 = 16 minutes
*38 Entry Delay
Exit Delay = Entry + 15 seconds		 I_2_I 1 = 20 seconds
2 = 30 seconds
3 = 45 seconds
4 = 60 seconds
5 = 90 seconds
*39 Audible Exit Warning I_1_I 0 = No
1 = Yes
*40 PABX Access Code I_ _I_ _I_ _I_ _I (If 9 is needed to dial add here)
*41 Primary Phone (12 digits) I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
End Phone with * # + 11 = * # + 12 = # # + 13 = 2.5 second pause
*42 Secondary Phone I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
(This panel cannot do pagers)
*43 Subscriber Account I_ _I_ _I_ _I_ _I
Note: Hex A = # + 10 B = # + 11 C = # + 12 D = # + 13 E = # + 14 F = # + 15
*45 Phone System Select I_1_I 0 = Pulse Dial
1 = DTMF Dial
2 = Pulse Dial, CS on Watts Line
3 = DTMF Dial, CS on Watts Line
*46 Report Format I_7_I 0 = 3/1, 4/1 Ademco L/S Standard
1 = 3/1, 4/1 Radionics Standard
2 = 4/2 Ademco L/S Standard
3 = 4/2 Radionics Standard
6 = 4/2 Ademco Express
7 = Contact ID
8 = 3/1, 4/1 Ademco L/S Expanded
9 = 3/1, 4/1 Radionics Expanded
*47 Split/Dual Reporting (No Pagers!) I_0_I
To Primary Phone To Secondary Phone
0 = All Reports Backup only
1 = Alarms, Restore, Cancel All Other Reports
2 = All Reports except Open/Close, Test Open/Close, Test
3 = Alarms, Restore, Cancel All Reports
4 = All Reports except Open/Close, Test All Reports
5 = All Reports (Dual Reporting) All Reports
*48 15 Sec Burg Dial Delay I_0_I 0 = No
1 = Yes
*49 Periodic Test Message I_3_I 0 = None
1 = 24 Hours
2 = Weekly
3 = Monthly
*50 Sescoa/Radionics I_0_I 0 = No
1 = Yes
*51 Confirmation of Arming Ding I_0_I 0 = No
1 = Yes
2 = Yes for RF Arming)
(6139 Alpha keypad is required for programming Zones)
*56 Zone Assignments (Max 30 wireless zones in addition to the 2 onboard zones)
Hardwire Zones 05 & 06
4219/4229 Zone Expander Zones 10 to 17 (depends on receiver capacity)
Police Panic Zone 07
Duress Zone 08
Receiver Tamper/Trouble Zone 09
Wireless Zones 10 to 30
Fire Panic Zone 95
Medical Panic Zone 96
1. “Enter Zn No.” enter zone to program then press * or 00 to quit
2. Keypad will show summary of zones programming, press *
3. “Zone Type?” enter type then * 00 = Zone Disabled/Deleted
01 = Delay Zone
02 = Do not Use
03 = Perimeter/Instant
04 = Interior Follower/Motions
05 = Trouble by Day/Alarm by Night
06 = 24 hour Silent/Holdup
07 = 24 hour Police Panic
08 = 24 hour Aux/Medical
09 = Fire
10 = Interior Delay
20 = Arm-Stay (RF only)
21 = Arm-Away (RF only)
22 = Disarm (RF only)
23 = No Alarm Response
4. “Report Code?” enter 10 then *
5. “Input Device?” enter device then * 1 for Hardwired
2 for Auxiliary Wired (with 4219/4229 Expander)
3 for Supervised RF (most sensors are RF)
4 for Un-Supervised RF
5 RF Button Type (Keyfobs/Panics etc)
6. Cursor should flash above “LP#”, Enter Loop number 1 to 4 depending on sensor
Door Switch – Loop 1 = External Sensor Connector
– Loop 2 = Internal Reed Switch
Glassbreak – Loop 1
Smoke Detectors – Loop 1
Motions – Loop 1
Keyfobs – Loop 1 = Bottom Right Button (Each button counts as 1 zone)
– Loop 2 = Top Right Button
– Loop 3 = Top Left Button
– Loop 4 = Bottom Left Button
7. “Learn Sensor Y/N?” press 1 and trip sensor twice, you cannot manually enter serial number
8. “Alpha Program?” press 0 if not programming Alpha descriptions
9. ” Keypad shows new summary of programming or be back to “Enter zone number”
10. If finished programming zones enter 00 at “Enter zone no” to return to normal programming
*60 Trouble Report Code I_1_I_0_I
*61 Bypass Report Code I_0_I_0_I
*62 AC Loss Report Code I_1_I_0_I
*63 Low Bat Report Code I_1_I_0_I
*64 Test Report Code I_0_I_0_I
*65 Open (Disarm)/Exit Alarm I_0_I_0_I Opening Report
I_0_I_0_I Exit Alarm
*66 Away/Stay Close I_0_I_0_I
*67 RF Xmtr Low Bat I_0_I_0_I
*68 Cancel Report Code I_1_I_0_I
*69 Group Restores for Trouble I_0_I
RF Low Bat, Bypass
*70 Alarm Restore Code I_0_I
*71 Trouble Restore Code I_0_I_0_I
*72 Bypass Restore Code I_0_I_0_I
*73 AC Restore Code I_0_I_0_I
*74 Low Bat Rest Code I_0_I_0_I
*75 RF Low Bat Rest Code I_0_I_0_I
*80 Output Relays (Usually program only if 4204 Relay is enabled in *25)
*81 Output Relays (Usually program only if 4204 Relay is enabled in *25)
*82 Custom Alpha Editing (Leave Alone)
*83 Add/Delete 5800 RF Input IDs (Alternate way of programming sensors, not normally used)
*92 Reports per Armed Period I_0_I 0 = 10 per armed period
1 = Unlimited per Armed period
*94 Download Phone Number I_1_I_8_I_0_I_0_I_7_I_6_I_2_I_7_I_8_I_3_I_1_I_ _I
*95 Ring Count I_# 15_I 0 to #15 #15 Enables Downloading
*96 Reinitialize Download (No Value needed, keypad will just beep and reset CSID and account to all F’s)
*97 Default Panel (No Value needed, keypad will beep and default panel)
*98 Exits Program Mode (Will not allow re-entry with Installer Code + 8 + 0 + 0)
*99 Exits Program Mode (Will allow re-entry with Code + 8 + 0 + 0)