|
||||||||||||||||||||||||
|
||||||||||||||||||||||||
*20 Installer Code | I_6_I_3_I_2_I_1_I | |||||||||||||||||||||||
*21 Quick Arm Enable | I_1_I |
0 = No 1 = Yes |
||||||||||||||||||||||
*22 RF (Wireless) System Type | I_?_I |
0 = None 1 = 5800 wireless with 5881 receiver 4 = 5800 wireless with 5881 RF Jamming |
||||||||||||||||||||||
*23 Force Bypass Enable | I_0_I |
0 = No 1 = Yes |
||||||||||||||||||||||
*24 RF House Code | I_0_I_0_I | 00 = Disabled / 01-31 | ||||||||||||||||||||||
Used only with 5700 series wireless 5804BD keyfob and 5827BD Keypad (House Code must match sensors) |
||||||||||||||||||||||||
*25 Output Relay Module | I_0_I |
0 = None 3 = 4204 Relay Module |
||||||||||||||||||||||
*26 4284/4285 Voice Module Code (Allows access to Voice module) |
I_0_I_0_I |
00 = Disabled 1st digit = 1 to 9 2nd digit = # + 11 = * or # + 12 = # |
||||||||||||||||||||||
*27 Output to Long Range Radio | I_0_I |
0 = No 1 = Yes |
||||||||||||||||||||||
*28 Single Alarm Sound/Zone | I_0_I |
0 = No 1 = Yes |
||||||||||||||||||||||
*29 Fire Sounder Timeout | I_1_I |
0 = Yes 1 = No Fire Timeout |
||||||||||||||||||||||
*30 Alarm Bell Timeout | I_2_I |
0 = None 1 = 4 minutes 2 = 8 minutes 3 = 12 minutes 4 = 16 minutes |
||||||||||||||||||||||
*36 Exit Delay | I_6_I_0_I | 0 – 99 seconds | ||||||||||||||||||||||
*37 Entry Delay 1 | I_3_I_0_I | 0 – 99 seconds | ||||||||||||||||||||||
*38 Entry Delay 2 | I_3_I_0_I | 0 – 99 seconds | ||||||||||||||||||||||
*39 Audible Exit Warning | I_1_I |
0 = No 1 = Yes |
||||||||||||||||||||||
*40 PABX Access Code | I__I__I__I__I__I__I | (If 9 is needed to dial add here) | ||||||||||||||||||||||
*41 Primary Phone (12 digits) |
I__I__I__I__I__I__I__I__I__I__I__I__I End Phone with * # + 11 = * # + 12 = # # + 13 = 2.5 second pause |
|||||||||||||||||||||||
*42 Secondary Phone |
I__I__I__I__I__I__I__I__I__I__I__I__I Pager on this panel is location *90 |
|||||||||||||||||||||||
*43 Subscriber Account |
I__I__I__I__I Hex A = # + 10 B = # + 11 C = # + 12 D = # + 13 E = # + 14 F = # + 15 |
|||||||||||||||||||||||
*45 Phone Sys Select | I_1_I |
0 = Pulse Dial 1 = DTMF Dial 2 = Pulse Dial, CS on Watts Line 3 = DTMF Dial, CS on Watts Line |
||||||||||||||||||||||
*47 Split/Dual Reporting | I_0_I | (use 6 for pagers) | ||||||||||||||||||||||
|
||||||||||||||||||||||||
*48 15 Sec Burg Dial Delay | I_0_I |
0 = No 1 = Yes |
||||||||||||||||||||||
*49 Periodic Test Message | I_3_I |
0 = None 1 = 24 Hours 2 = Weekly 3 = Monthly |
||||||||||||||||||||||
*51 Confirmation of Arming Ding | I_0_I |
0 = No 1 = Yes 2 = Yes for RF Arming (keyfobs etc) |
||||||||||||||||||||||
*52 Zone 3 Response | I_0_I |
0 = 400 ms 1 = 10 ms |
||||||||||||||||||||||
*53 Zone 25 Response | I_0_I |
0 = 15 seconds 1 = 1 Minute 2 = 2 Minutes 3 = 3 Minutes (etc) |
||||||||||||||||||||||
Must use 6139 Alpha Keypad here | ||||||||||||||||||||||||
*56 Zone Assignments (Max 16 hardwired and/or wireless zones in addition to the 8 onboard zones) | ||||||||||||||||||||||||
Hardwire | Zones 01 to 06 | |||||||||||||||||||||||
4219/4229 Zone Expander | Zones 10 to 17 (depends on receiver capacity) | |||||||||||||||||||||||
Police Panic | Zone 07 | |||||||||||||||||||||||
Duress | Zone 08 | |||||||||||||||||||||||
Receiver Tamper/Trouble | Zone 09 | |||||||||||||||||||||||
Wireless | Zones 10 to 30 | |||||||||||||||||||||||
Fire Panic | Zone 95 | |||||||||||||||||||||||
Medical Panic | Zone 96 | |||||||||||||||||||||||
1. At “Program Tool?” press 0, if “Set to Confirm?” shows press 1 | ||||||||||||||||||||||||
2. “Enter Zn No.” enter zone to program then press * | ||||||||||||||||||||||||
3. Keypad will show summary of zones programming, press * | ||||||||||||||||||||||||
4. “Zone Type?” enter type then * |
00 = Zone Disabled/Deleted 01 = Delay Zone 02 = Do not Use 03 = Perimeter/Instant 04 = Interior Follower/Motions 05 = Trouble by Day/Alarm by Night 06 = 24 hour Silent/Holdup 07 = 24 hour Police Panic 08 = 24 hour Aux/Medical 09 = Fire 10 = Interior Delay 20 = Arm-Stay (RF only) 21 = Arm-Away (RF only) 22 = Disarm (RF only) 23 = No Alarm Response 25 = Oil Tank Monitor |
|||||||||||||||||||||||
5. “Report Code?” enter 10 then * | ||||||||||||||||||||||||
6. “Input Device?” enter device then * |
1 for Hardwired 2 Not Used 3 for Supervised RF (most sensors are RF) 4 for Un-Supervised RF 5 RF Button Type (Keyfobs/Panics etc) |
|||||||||||||||||||||||
(New versions may skip step 7 and move to step 8, learn Loop number after learning sensor) | ||||||||||||||||||||||||
7. Cursor should flash above “LP#”, Enter Loop number | ||||||||||||||||||||||||
Door Switch | – Internal switch loop 2, – external connector loop 1 |
|||||||||||||||||||||||
Glassbreak | – Loop 1 | |||||||||||||||||||||||
Smoke Detectors | – Loop 1 | |||||||||||||||||||||||
Motions | – Loop 1 | |||||||||||||||||||||||
Keyfobs |
– Bottom Right Button = Loop 1 – Top Right Button = Loop 2 (Each button counts as 1 zone) – Top Left Button = Loop 3 – Bottom Left Button = Loop 4 |
|||||||||||||||||||||||
8. at “Serial Prog?” or “Learn S/N” press 1 and either enter serial number or trip sensor twice | ||||||||||||||||||||||||
Note: | Serial numbers found on sticker on of sensor, if not, learn by tripping sensor | |||||||||||||||||||||||
9. “Alpha Program?” press 0 if not programming Alpha descriptions | ||||||||||||||||||||||||
10. ” Keypad shows new summary of programming or be back to “Enter zone number” | ||||||||||||||||||||||||
11. If finished programming zones enter 00 at “Enter zone no” to return to normal programming | ||||||||||||||||||||||||
*60 Trouble Report Code | I_1_I_0_I | |||||||||||||||||||||||
*61 Bypass Report Code | I_0_I_0_I | |||||||||||||||||||||||
*62 AC Loss Report Code | I_0_I_0_I | |||||||||||||||||||||||
*63 Low Bat Report Code | I_0_I_0_I | |||||||||||||||||||||||
*64 Test Report Code | I_1_I_0_I | |||||||||||||||||||||||
*65 Open (Disarm)/Exit Alarm | I_0_I_0_I |
1st digit = Opening Report 2nd digit = Exit Alarm |
||||||||||||||||||||||
*66 Away/Stay Report |
I_0_I Away I_0_I Stay |
|||||||||||||||||||||||
*67 RF Xmtr Low Bat | I_0_I_0_I | |||||||||||||||||||||||
*68 Cancel Report Code | I_1_I_0_I | |||||||||||||||||||||||
*69 Group Restore Tble/RF/Bypass | I_0_I | |||||||||||||||||||||||
*70 Alarm Restore Code | I_0_I | (Required if smoke on system) | ||||||||||||||||||||||
*71 Trouble Restore Code | I_0_I_0_I | |||||||||||||||||||||||
*72 Bypass Restore Code | I_0_I_0_I | |||||||||||||||||||||||
*73 AC Restore Code | I_0_I_0_I | |||||||||||||||||||||||
*74 Low Bat Rest Code | I_0_I_0_I | |||||||||||||||||||||||
*75 RF Low Bat Rest Code | I_0_I_0_I | |||||||||||||||||||||||
*80 Output Relays (Usually program only if 4204 Relay is enabled in *25) | ||||||||||||||||||||||||
*81 Output Relays (Usually program only if 4204 Relay is enabled in *25) | ||||||||||||||||||||||||
*82 Custom Alpha Editing (Do not Program) | ||||||||||||||||||||||||
*83 Sequential Mode (Alternate way of programming sensors, not used) | ||||||||||||||||||||||||
*90 Pager Custom Data |
I__I__I__I__I__I__I__I__I__I__I__I__I End Phone with * # + 11 = * # + 12 = # # + 13 = 2.5 second pause |
|||||||||||||||||||||||
*91 Option Selection | I_0_I |
0 = None 4 = AAV 2-way module enable 8 = Exit Delay Restart (4 turns off siren sounds during 2-way) |
||||||||||||||||||||||
*92 Reports per Armed Period | I_0_I |
0 = 10 per armed period 1 = Unlimited per Armed period |
||||||||||||||||||||||
*94 Download Phone Number | I_1_I_8_I_0_I_0_I_7_I_6_I_2_I_7_I_8_I_3_I_1_I__I | |||||||||||||||||||||||
*95 Ring Count | I_# 15_I | (0 to #15 #15 = Answer Machine) | ||||||||||||||||||||||
*96 Reinitialize Download (No Value needed, keypad will just beep and reset CSID and account to all F’s) | ||||||||||||||||||||||||
*97 Default Panel (No Value needed, keypad will beep and default panel) | ||||||||||||||||||||||||
Note: | (This will lock out this panel and set back to ADT defaults) | |||||||||||||||||||||||
*98 Exits Program Mode (Will not allow re-entry with Installer Code + 8 + 0 + 0) | ||||||||||||||||||||||||
*99 Exits Program Mode (Will allow re-entry with Code + 8 + 0 + 0) |