| *20 |
Master Code |
I_4_I_1_I_1_I_0_I |
(Default is 4110) |
| *21 |
Quick Arm Enable |
I_1_I |
0 = No
1 = Yes
|
| *22 |
Keyswitch Enable |
I_0_I |
0 = No
1 = Yes
|
| *23 |
Force Bypass Enable |
I_0_I |
0 = No
1 = Yes
|
| *24 |
RF House Code |
I_0_I_0_I |
00 = Disabled
01 to 31 if using 5700 Wireless sensors
90 If using 4219 Hardwire Zone Expander
|
| *27 |
Audible Exit Warning |
I_1_I |
0 = No
1 = Yes
|
| *28 |
Confirmation of Arming Ding |
I_0_I |
0 = No
1 = Yes
|
| *29 |
Fire Sounder No Timeout |
I_1_I |
0 = No
1 = Yes
|
| *30 |
Alarm Bell Timeout |
I_2_I |
1 = 4 minutes
2 = 8 minutes
3 = 12 minutes
4 = 16 minutes
|
| *31 |
Zone 1 Definition |
I_?_I |
(Smoke Detectors must use Zone 5)
0 = Zone Disabled
1 = Entry/Exit
2 = Not Used
3 = Instant/Perimeter
4 = Interior/PIR
5 = Trouble by Day
6 = 24 hr Silent (Holdup)
7 = 24 hr Audible (Police Panic)
8 = 24 hr Auxiliary (Medical)
9 = Fire without timeout (Smokes)
10 = Interior with Delay
|
| *32 |
Zone 2 Definition |
I_?_I |
| *33 |
Zone 3 Definition |
I_?_I |
| *34 |
Zone 4 Definition |
I_?_I |
| *35 |
Zone 5 Definition |
I_?_I |
| *36 |
Zone 6 Definition |
I_?_I |
| *37 |
Zone 7 Definition (Panic * & #) |
I_7_I |
| *38 |
Entry Delay
Exit Delay = Entry + 15 seconds
|
I_2_I |
1 = 20 seconds
2 = 30 seconds
3 = 45 seconds
4 = 60 seconds
5 = 90 seconds
|
| *39 |
Zone 3 Response to open |
I_0_I |
0 = 400ms
1 = 10ms
|
| *40 |
PABX Access Code |
I_ _I_ _I_ _I_ _I |
(If 9 is needed to dial add here) |
| *41 |
Primary Phone (12 digits)
End Phone with *
|
I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
# + 11 = * # + 12 = # # + 13 = 2.5 second pause
|
| *42 |
Secondary Phone |
I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I_ _I
Note: Pager only available on VERY new 4110XMP’s,
pager will not work if Account starts with 0
|
| *43 |
Subscriber Account |
I_ _I_ _I_ _I_ _I
Note: Hex A = # + 10 B = # + 11 C = # + 12 D = # + 13 E = # + 14 F = # + 15
|
| *44 |
Report Format |
I_7_I |
0 = 3/1, 4/1 Ademco L/S Standard
1 = 3/1, 4/1 Radionics Standard
2 = 4/2 Ademco L/S Standard
3 = 4/2 Radionics Standard
6 = 4/2 Ademco Express
7 = Contact ID
8 = 3/1, 4/1 Ademco L/S Expanded
9 = 3/1, 4/1 Radionics Expanded
|
| *45 |
Phone Sys Select |
I_1_I |
0 = Pulse Dialing
1 = DTMF Dialing
2 = Pulse Dialing, CS on Watts Line
3 = DTMF Dialing, CS on Watts Line
|
| *46 |
Sescoa/Radionics Select |
I_0_I |
0 = Radionics
1 = Sescoa
|
| *47 |
15 Sec Burg Dial Delay |
I_0_I |
0 = No
1 = Yes
|
| *48 |
Periodic Test Message |
I_0_I |
0 = None
1 = 24 Hours
2 = Weekly
|
| *49 |
Split/Dual Reporting |
I_0_I |
|
To Primary Phone
0 = All Reports
1 = Alarms, Restore, Cancel
2 = All Reports except Open/Close, Test
3 = Alarms, Restore, Cancel
4 = All Reports except Open/Close, Test
5 = All Reports (Dual Reporting)
The following is only available with very new
6 = All reports except Open/Close
7 = All reports
8 = All reports
9 = All reports except Open/Close
|
To Secondary Phone
Backup Only
All Other Reports
Open/Close, Test
All Reports
All Reports
All Reports
4110XMP’s, use 6 if programming Pagers
Alarms, Open/Close, Troubles
Alarms, Troubles
Alarms, Open/Close, Troubles
Alarms, Open/Close for Users 5-25, Troubles
|
|
| *50 |
Keypad Medical/Fire |
1 & * I_1_I
3 & # I_1_I
|
(Silent, sends 95)
(Audible, sends 96)
(This section may not be available on older models,
display will show EE)
|
| *51 |
Zone 1 Report Code |
I_1_I_0_I |
| *52 |
Zone 2 Report Code |
I_1_I_0_I |
| *53 |
Zone 3 Report Code |
I_1_I_0_I |
| *54 |
Zone 4 Report Code |
I_1_I_0_I |
| *55 |
Zone 5 Report Code |
I_1_I_0_I |
| *56 |
Zone 6 Report Code |
I_1_I_0_I |
| *57 |
Zone 7 Police Panic Report Code |
I_1_I_0_I |
| *58 |
Zone 8 Duress Report Code |
I_1_I_0_I |
| *59 |
Zone 9 Receiver Fail Report Code |
I_0_I_0_I |
| *60 |
Trouble Report Code |
I_1_I_0_I |
| *61 |
Bypass Report Code |
I_1_I_0_I |
| *62 |
AC Loss Report Code |
I_1_I_0_I |
| *63 |
Low Bat Report Code |
I_1_I_0_I |
| *64 |
Test Report Code |
I_0_I_0_I |
| *65 |
Open Report Code |
I_0_I |
| *66 |
Close Report Code |
I_0_I |
| *67 |
RF Xmtr Low Bat |
I_0_I_0_I |
| *68 |
Cancel Report Code |
I_1_I_0_I |
| *69 |
Group Restores Trouble/Bypass |
I_0_I |
| *70 |
Alarm Restore Code |
I_0_I |
| *71 |
Trouble Restore Code |
I_0_I_0_I |
| *72 |
Bypass Restore Code |
I_0_I_0_I |
| *73 |
AC Restore Code |
I_0_I_0_I |
| *74 |
Low Bat Rest Code |
I_0_I_0_I |
| *75 |
RF Low Bat Restore Code |
I_0_I_0_I |
|
| *76 to *79 available if 4281L (Low) Receiver |
| *76 to *83 available if 4281M (Medium) or 4281H (High) Receiver or 4219 Hardwire Zone Expander |
| *76 to *92 available if 4281H (High) Receivers |
|
| *76 |
1st Wireless Zone Definition |
I_?_I_?_I
I_1_I_0_I
|
Zone Number
Report Code
|
|
Zone defines type of sensor |
Zone 10 to 13 = Delay zone
Zone 14 to 29 = Instant/Burg
Zone 30 to 43 = Interior/PIR
Zone 44 to 45 = Interior w/Delay
Zone 46 to 47 = Instant/Burg
Zone 48 to 55 = Fire/Smoke Detector
Zone 56 to 61 = Day Zone
Zone 62 = 24 hr Audible
Zone 63 = Programmed in *92
|
| *77 |
2nd Wireless Zone |
I_?_I_?_I
I_1_I_0_I
|
Zone Number
Report Code
|
| *78 |
3rd Wireless Zone |
I_?_I_?_I
I_1_I_0_I |
Zone Number
Report Code |
| *79 |
4th Wireless Zone |
I_?_I_?_I
I_1_I_0_I |
Zone Number
Report Code |
| *80 |
5th Wireless Zone |
I_?_I_?_I
I_1_I_0_I |
Zone Number
Report Code |
| *81 |
6th Wireless Zone |
I_?_I_?_I
I_1_I_0_I |
Zone Number
Report Code |
| *82 |
7th Wireless Zone |
I_?_I_?_I
I_1_I_0_I |
Zone Number
Report Code |
| *83 |
8th Wireless Zone |
I_?_I_?_I
I_1_I_0_I |
Zone Number
Report Code |
| *84 |
9th Wireless Zone |
I_?_I_?_I
I_1_I_0_I |
Zone Number
Report Code |
| *85 |
10th Wireless Zone |
I_?_I_?_I
I_1_I_0_I |
Zone Number
Report Code |
| *86 |
11th Wireless Zone |
I_?_I_?_I
I_1_I_0_I |
Zone Number
Report Code |
| *87 |
12th Wireless Zone |
I_?_I_?_I
I_1_I_0_I |
Zone Number
Report Code |
| *88 |
13th Wireless Zone |
I_?_I_?_I
I_1_I_0_I |
Zone Number
Report Code |
| *89 |
14th Wireless Zone |
I_?_I_?_I
I_1_I_0_I |
Zone Number
Report Code |
| *90 |
15th Wireless Zone |
I_?_I_?_I
I_1_I_0_I |
Zone Number
Report Code |
| *91 |
16th Wireless Zone |
I_?_I_?_I
I_1_I_0_I |
Zone Number
Report Code |
| *92 |
Zone Response of Zone 63 |
I_0_I |
0, 6, 7, 8, 9 only |
| *93 |
Reports Per Armed Period |
I_0_I |
0 = 10 Reports
1 = Unlimited
|
| *94 |
Download Phone Number |
I_1_I_8_I_0_I_0_I_7_I_6_I_2_I_7_I_8_I_3_I_1_I_ _I |
| *95 |
Ring Count |
I_# 15_I |
0 to #15 #15 = Answer Machine |
| *96 |
Reinitialize Download (No Value needed, keypad will just beep and reset CSID and account to all F’s) |
| *97 |
Default Panel (No Value needed, keypad will beep and default panel) |
| *98 |
Exits Program Mode (Will not allow re-entry with Installer Code + 8 + 0 + 0) |
| *99 |
Exits Program Mode (Will allow re-entry with Code + 8 + 0 + 0) |
